Yahoo Groups archive
Messages
Page 110 of 307 · 15341 messages matched
2007-08-10 by Zack Widup
Hi Anant, What exactly do you want the AVR chip to do with the camera? Zack On Fri, 10 Aug 2007, anant wrote: > I have a problem it has basically 2 parts > 1)interfacing a CMOS coamera with AVR microcontroller. > 2) transmitting vedio streaming through lan cable with ethernetcont
2007-08-10 by Ralph Hilton
On Fri, 10 Aug 2007 10:08:27 -0000 you wrote: >I have a problem it has basically 2 parts >1)interfacing a CMOS coamera with AVR microcontroller. >2) transmitting vedio streaming through lan cable with ethernetcontroller > >first part is relatively easy can any one guide me about
2007-08-10 by Cat
Did you install service packs, both to windows and AVRstudio? Cat ----- Original Message ----- From: "Thomas Keller" To: Sent: Thursday, August 09, 2007 6:30 PM Subject: Re: [AVR-Chat] oops > Actually, since having to reinstall Win2K Pro due to an HDD crash, I > can. I looked in
2007-08-10 by Leon
----- Original Message ----- From: "Tim Mitchell" To: Sent: Friday, August 10, 2007 8:49 AM Subject: RE: [AVR-Chat] How to connect AVR microcontroller with USB?? > John Samperi wrote: >> At 04:05 PM 10/08/2007, you wrote: >>> Does anyone know how to connect AVR microcontroller wi
2007-08-10 by anant
I have a problem it has basically 2 parts 1)interfacing a CMOS coamera with AVR microcontroller. 2) transmitting vedio streaming through lan cable with ethernetcontroller first part is relatively easy can any one guide me about the second part also if any one has any suggestion f
2007-08-10 by Tim Mitchell
John Samperi wrote: > At 04:05 PM 10/08/2007, you wrote: >> Does anyone know how to connect AVR microcontroller with USB? Where >> can I get the simply method for this? > > If the AVR is a slave just use one the FTDI (or similar) chips. > > If a master then it gets a lot more com
2007-08-10 by Ralph Hilton
On Fri, 10 Aug 2007 13:05:05 +0700 you wrote: >Does anyone know how to connect AVR microcontroller with USB? Where can I >get the simply method for this? > > > >Regards, > > > >Mujahidin ( http://iddhien.com ) http://www.ftdichip.com/ has some easy to use modules. http://www.olim
2007-08-10 by John Samperi
At 04:05 PM 10/08/2007, you wrote: >Does anyone know how to connect AVR microcontroller with USB? Where can I >get the simply method for this? If the AVR is a slave just use one the FTDI (or similar) chips. If a master then it gets a lot more complicated and you will need either
2007-08-10 by none
Is there a setting to display line numbers in the editor in avr studio when debugging C source code. Lines numbered in succession from first line down would be handy. I can not find this setting perhaps it does not exist. Owen.
2007-08-10 by Mujahidin
Does anyone know how to connect AVR microcontroller with USB? Where can I get the simply method for this? Regards, Mujahidin ( http://iddhien.com ) [Non-text portions of this message have been removed]
2007-08-10 by Bobby
search for ATAVRDRAGON --- In AVR-Chat@yahoogroups.com, "Mujahidin" wrote: > > Does anyone know how to connect AVR microcontroller with USB? Where can I > get the simply method for this? > > > > Regards, > > > > Mujahidin ( http://iddhien.com ) > > > > [Non-text portions of this
2007-08-10 by Thomas Keller
Actually, since having to reinstall Win2K Pro due to an HDD crash, I can. I looked in the known issues area, and see nothing relevant. Also, the program was counting before (I lost the sources when my HDD crashed )-: ). I have no working floppy diskette drive, controller died, so
2007-08-09 by John Samperi
At 02:02 AM 10/08/2007, you wrote: >OOps I forgot to include the code *doh*: and that the simulator doesn't really work that well with timers. Have you looked at the known issues? oh you can't open the help file, I forgot. Regards John Samperi ************************************
2007-08-09 by Thomas Keller
OOps I forgot to include the code *doh*: ---- cut here ---- ;------------------------------------------------------------------------------ ; ; begin file intialization .include "tn25def.inc" ; include processor definition file ;---------------------------------------------------
2007-08-09 by Thomas Keller
Probably something really stupid I am doing wrong, but the following code is not working. Accroding to the simulator, timer/counter1 is not counting at all. Any ideas why not? Tom
2007-08-09 by dlc@frii.com
I await the cyberpunk concept of "black ice" to be implemented when dealing with SPAMmers. DLC > They should be given 20 years in the electric chair and then hanged. > :-) > > Zack > > On Thu, 9 Aug 2007, John Samperi wrote: > >> At 06:54 PM 9/08/2007, you wrote: >> >>> > Site is
2007-08-09 by Jim Wagner
Its back up. Jim Wagner On Thu, 9 Aug 2007 08:16:52 -0500 (CDT) Zack Widup wrote: > > They should be given 20 years in the electric chair and > then hanged. > :-) > > Zack > > On Thu, 9 Aug 2007, John Samperi wrote: > > > At 06:54 PM 9/08/2007, you wrote: > > > >> > Site is down
2007-08-09 by Robert Adsett
At 11:48 AM 8/9/2007 +0200, Manne Tallmarken wrote: >Do you have and url to BlueLine A 565 ? http://www.bluelineinc.com/vc/VWvisuelfiche/AD0A0C482E6A16BD85256EA60080013E?opendocument&niv=3&LG=EN&cle=B1C6E3EE5BA9744A85256EA6007FD583&cle2=39AEECBB65D376EB85256EA6007FD657&GR=BLEN An
2007-08-09 by Zack Widup
They should be given 20 years in the electric chair and then hanged. :-) Zack On Thu, 9 Aug 2007, John Samperi wrote: > At 06:54 PM 9/08/2007, you wrote: > >> > Site is down due to maintenance, sorry for the inconvenience. >> > >> > - The Sysadmin team >> >> Was there any warning
2007-08-09 by Manne Tallmarken
Do you have and url to BlueLine A 565 ? Thanks Manne > Manne Tallmarken Wrote >>I need a project logger for my projects. Last night I was up and searched > for bad >solderings, I swapped random components and did other crazy things >>that did not solve the actual problem. This ha
2007-08-09 by John Samperi
At 06:54 PM 9/08/2007, you wrote: > > Site is down due to maintenance, sorry for the inconvenience. > > > > - The Sysadmin team > >Was there any warning of this, or when it's likely to return? There have been a few attacks to the site in the past few weeks. Yesterday there was a
2007-08-09 by Mark Nowell
> Site is down due to maintenance, sorry for the inconvenience. > > - The Sysadmin team Was there any warning of this, or when it's likely to return? Mark
2007-08-08 by subscriptions@aeolusdevelopment.com
Manne Tallmarken Wrote >I need a project logger for my projects. Last night I was up and searched for bad >solderings, I swapped random components and did other crazy things >that did not solve the actual problem. This happens too often, so it's really time to >keep up logs of al
2007-08-08 by Manne Tallmarken
I need a project logger for my projects. Last night I was up and searched for bad solderings, I swapped random components and did other crazy things that did not solve the actual problem. This happens too often, so it's really time to keep up logs of all projects. Which project l
2007-08-02 by David VanHorn
> >If I could Test (save) and Disable Interrupts with an indivisible > >instruction, run the process then return the original Global > >Interrupt state I would feel a bit safer... > > No REALLY sure what you are trying to do but here we go.... > There are no INVISIBLE instruction
2007-08-02 by John Samperi
At 04:49 PM 2/08/2007, you wrote: >If I could Test (save) and Disable Interrupts with an indivisible >instruction, run the process then return the original Global >Interrupt state I would feel a bit safer... No REALLY sure what you are trying to do but here we go.... There are no
2007-08-02 by thormj_altea
--- In AVR-Chat@yahoogroups.com, Zack Widup wrote: > > > This is all very fascinating. I have had it in my mind to some day build > something like this just for fun: > > http://www.westmountainradio.com/Whattmeter.htm > > I figure I can put something together for far less than th
2007-08-02 by thormj_altea
Low-side sensing is usually a better way (cheaper, higher performance, etc) unless the device you're monitoring insists on being connected to ground. Analog Devices also makes a couple of good parts (and has a good sampling program): AD628 - Good for 100V CM AD629 - Good for 270V
2007-08-02 by Mark
Hi Guys, I am a relative newcomer to the ATmega128 and have a question about semaphore (and general flag) management. I have been looking for an ATmega128 instruction that allows a flag to be tested then set in a single instruction while not allowing interrupts during it's execut
2007-08-01 by Zack Widup
This is all very fascinating. I have had it in my mind to some day build something like this just for fun: http://www.westmountainradio.com/Whattmeter.htm I figure I can put something together for far less than the cost of this unit, without the need for all the bells and whistle
2007-08-01 by mago Umandam
Hi Ned, Thanks a lot... Actually, i saw that IC on the net when i was searching for a solution.. But im having difficulty to find the IC. I am in singapore and i buy components from farnell only. Farnell singapore doesnt have LT6102. I dunno any electronics store here. Since a lo
2007-08-01 by maria mastik
Hi well one approach is to use one power supply for your OpAmp and ADC. this powersupply should be isolated from the 70V voltage and from other digital circuits you have. well now the ADC will generate the correct value but the 0V and 5V of the ADC output is based on its own GND
2007-08-01 by Ned Konz
magzky02 wrote: > Hello all, > > I am going to measure the current (0-500mA) on a system. i will be > using a current sense resistor, and an op-amp then i use ADC to > measure the opm-amp output. But my problem is that the the line is > high voltage (70 V). I am thinking to isola
2007-08-01 by dilipsilga
--- In AVR-Chat@yahoogroups.com, "eko_saja" wrote: > > --- In AVR-Chat@yahoogroups.com, Ali Ghadirzadeh > wrote: > > > > Hi: > > I have a problem with my compiler. > > I use bascom to compile my programs but recently I can't send the > program to the chip. > > the error is: > > "
2007-07-31 by Bob Paddock
On Monday 30 July 2007 01:21, magzky02 wrote: > I am going to measure the current (0-500mA) on a system. i will be > using a current sense resistor, and an op-amp then i use ADC to > measure the opm-amp output. But my problem is that the the line is > high voltage (70 V). "Semina
2007-07-31 by Cat C
Did you install "giveio"? Cat ----Original Message Follows---- From: Ali Ghadirzadeh Reply-To: AVR-Chat@yahoogroups.com To: AVR-Chat@yahoogroups.com Subject: Re: [AVR-Chat] stk 200 / 300 Date: Tue, 31 Jul 2007 10:02:04 -0700 (PDT) No I don't use buffer for stk200/300 I just use t
2007-07-31 by Ali Ghadirzadeh
No I don't use buffer for stk200/300 I just use the simplest circuit for it. sck ====> pin6 of lpt mosi ===> pin7 of lpt and ... I am having this problem even when I open bascom.also I face to that problem when I choose stk from programmer type menu. I have used this programmer f
2007-07-31 by eko_saja
--- In AVR-Chat@yahoogroups.com, Ali Ghadirzadeh wrote: > > Hi: > I have a problem with my compiler. > I use bascom to compile my programs but recently I can't send the program to the chip. > the error is: > "Stk 200 or Stk 300 not found, try again? Y or N" > How can I fix this p
2007-07-30 by Ali Ghadirzadeh
Hi: I have a problem with my compiler. I use bascom to compile my programs but recently I can't send the program to the chip. the error is: "Stk 200 or Stk 300 not found, try again? Y or N" How can I fix this problem? thanks a lot A.Gh --------------------------------- Park yours
2007-07-30 by subscriptions@aeolusdevelopment.com
mago Umandam Wrote >This is DC. The system is high voltage (70 V) low current (0-500mA)... > > regards, > mago > >Alex Shepherd wrote: > > A idea on how to >> measure current on high voltage systems is highly appreciated? > >Is it DC or AC and what sort of wave form? > >If it's A
2007-07-30 by Roy E. Burrage
Even with a differential amp, John, he'd have to worry about the measured system voltage. It's that common mode voltage dealy...especially when the source exceeds the amp's power supply. To be sure, he could use some clamping circuitry, but with the system differential it might j
2007-07-30 by johnmuchow
> A idea on how to > measure current on high voltage systems is highly appreciated? I agree with Roy, an isolation amplifier is perfect for this situation (Analog Devices AD202, Texas Inst. ISO124, or similar). But, since the voltage is only 70VDC and not the hundreds of volts is
2007-07-30 by Roy E. Burrage
If it's DC, Mago, make sure your low voltage and system voltages are referenced to the same low (DC return) potentials. Then stick your current sense resistor in the low line. Another option, with some additional spiff, would be to use an opto-isolator in its linear region to iso
2007-07-30 by mago Umandam
This is DC. The system is high voltage (70 V) low current (0-500mA)... regards, mago Alex Shepherd wrote: > A idea on how to > measure current on high voltage systems is highly appreciated? Is it DC or AC and what sort of wave form? If it's AC then maybe use a Current Transformer
2007-07-30 by Alex Shepherd
> A idea on how to > measure current on high voltage systems is highly appreciated? Is it DC or AC and what sort of wave form? If it's AC then maybe use a Current Transformer or one of those isolated Hall Effect current sensors and use your AtoD to measure the low-voltage side. A
2007-07-30 by magzky02
Hello all, I am going to measure the current (0-500mA) on a system. i will be using a current sense resistor, and an op-amp then i use ADC to measure the opm-amp output. But my problem is that the the line is high voltage (70 V). I am thinking to isolate the ground of the the lin
2007-07-24 by Tom Becker
> ... there will be a number of components that I can't shut off and I don't want to run into the situation where the battery is bled dry. If you can't allow a depleted battery (like LiIon and LiPos) you _must_ remove the load. There exist LDO regulators that provide integrated p
2007-07-24 by Cat
Disable all interrupts and put it to sleep? Cat ----- Original Message ----- From: "Reza Naima" To: Sent: Tuesday, July 24, 2007 4:06 AM Subject: [AVR-Chat] [ot] Li-Poly regulation > So I'm looking at deploying a device with a Li-Poly battery on board. > The voltage of a fully ch
2007-07-24 by Reza Naima
So I'm looking at deploying a device with a Li-Poly battery on board. The voltage of a fully charged battery should be 4.2V, and will drop over time. My application calls for a 3.3V source, and I was looking at using a LDO voltage regulator which has a *fault line to indicate whe
2007-07-24 by Zapper77DK
Hi Reza, Try looking at e.g. Seiko Instruments homepage (http://www.sii-ic.com/en/param_chrt.jsp?subcatID=5). There are a lot of semiconductor makers on the marked, which makes Li-Ion protection chips. Once lower discharge voltage is surpassed, the chip shuts the battery down (vi