Re: [oberheim] Re: Hola
2014-05-09 by zc40@...
if it appears that the voltage rises. V 5.53, I have two built in 4051 on a series of voices only. But the U711, change it and also I have tried another drive
Messages
Browse messages
Page 15 of 51 · 2518 messages matched
Re: [oberheim] Re: Hola
2014-05-09 by zc40@...
if it appears that the voltage rises. V 5.53, I have two built in 4051 on a series of voices only. But the U711, change it and also I have tried another drive
Re: [oberheim] Re: Hola
2014-05-08 by Patrick Edwards
Pull u711 and see if the voltage goes back up. ... -- Patrick Synth Tech @ http://www.switchedonaustin.com
Re: [oberheim] Re: Hola
2014-05-08 by <zc40@...>
Hello, I have set up all the pin feeds all 4051 (I have actually cut pin 16) and have raised the whole 4053, is out of the motherboard (u710). I ve also
Re: [oberheim] Re: Hola
2014-05-07 by Patrick Edwards
One thing that I have seen happen before is a CMOS latch-up that pulls down the +5.6 voltage which effectively destroys any voice control. The CEM outputs seem
Re: [oberheim] Re: Hola
2014-05-07 by Narfman96 - Narfland Studio
I m not sure where TP12 is on the schematic. Check D703 and the two capacitors near it. This circuit generates the 5.6v. It is shown on page 12 of the
Re: Hola
2014-05-07 by <zc40@...>
Hello, now I have another matrix unit that is correct, I ve tried. or 801/3/4/9/10/11/12 and all is well ... The cpu also think it s good. I see a strange
OB-Xa ROM images
2014-05-02 by rob hukin
Hi All, Does anyone have XA rev C ROM images they could send me or post to the Files section, please? thanks, rob.
OB5 schematic diagram
2014-04-27 by <altarkus2000@...>
Hello everyone, Do you know if there is any difference in circuitry between OB32 (squared) and the double manual OB5? Thanks a lot. Regards, Alex
Re: [oberheim] WTB/WTT: Anatek Pocket Filter / Midi Solutions Event Processor
2014-04-24 by rdwfour@...
http://www.midisolutions.com/ are still in business fwiw. On 04/24/14, gilwe@hotmail.com wrote: Hi, I m looking for one of these... if you have one which you d
WTB/WTT: Anatek Pocket Filter / Midi Solutions Event Processor
2014-04-24 by <gilwe@...>
Hi, I m looking for one of these... if you have one which you d like to sell or trade please email me: gil_we(at)yahoo.com Thanks !
Re: [oberheim] Re: Hola
2014-04-22 by Narfman96 - Narfland Studio
I m guessing you injected a signal into the DAC output and got a good loud signal at the output. Good job verifying the analog half of the circuit!!! Does
Re: [oberheim] Re: Hola
2014-04-22 by <zc40@...>
Hello, take long to respond. I ve been looking, I saw how it works this part and is in good condition, For the voices, no sound. I have seen all of this is
Re: [oberheim] Oberheim matrix 1000 - missing eprom
2014-04-20 by <justinboohan@...>
Well that s good news! I ran the calibration but not since I added the new voice chips, hopefully running it again will get it up to scratch. Cheers
Re: [oberheim] Re: Hola
2014-04-20 by Narfman96 - Narfland Studio
Ok my bad. It is U2. The print must say U2A. A video would be nice. It looks like the output of the 4053 should be pin 13. The input should be pin 14. This is
Re: [oberheim] Re: Hola
2014-04-20 by <zc40@...>
otherwise, I find u24, in the area near the top left corne, the U1, U2, U3, U4. but it is true that in the scheme puts u24 can be U2. ? I get confused?
Re: [oberheim] Re: Hola
2014-04-20 by <zc40@...>
I ve seen the diagrams, there are many things impossible to see, are sometimes difficult, I have a question, which multiplexes all signals of voices, the pin
Re: [oberheim] Re: Hola
2014-04-20 by Narfman96 - Narfland Studio
Do you have an actual audio signal through the potentiometer? If so work your way towards the output jack. U1, C4, etc. If not you can go back to U24 then the
Re: Hola
2014-04-20 by <zc40@...>
I m sending a signal from ableton a sequence, I played with Vel , but does not affect the output of the matrix, only noises that go in sync with the shot
Re: Hola
2014-04-20 by <zc40@...>
Hello Narfman. I tried regulators, 7912 & 7812. They look good, no voltage drop. The +5 & -5, also looks good. I have an oscilloscope Tetronix & genreador
Re: [oberheim] Hola
2014-04-20 by Narfman96 - Narfland Studio
Welcome to the group!!! Have you tried sending CC 07 with a value of 127 to see if the midi volume is turned down all the way? A reset may cure this also.
Hola
2014-04-20 by <zc40@...>
Hey guys great group, I like a lot. I ask. I have a 1000 matrix recently, The ignition and all good, but the preset does not have sound, some preset sounds,
Re: [oberheim] Oberheim matrix 1000 - missing eprom
2014-04-19 by Narfman96 - Narfland Studio
U802 is supposed to be missing. Did you run the calibrate procedure? On Saturday, April 19, 2014 8:21 AM, justinboohan@gmail.com
Oberheim matrix 1000 - missing eprom
2014-04-18 by <justinboohan@...>
Hi All, new to the group here, have a question about my oberheim matrix 1000. I purchased this a few years back on ebay, powered it up and had a quick listen
Re: [oberheim] Re: Matrix 1000 and SQ Midiquest 10 XL HELP
2014-03-29 by Marcelo Malmierca
Well, I gonna let some light about ObiMagiX6000 and Volt I start this enterprise Volt Crafty Devices two years ago. As a fan of synthetizers and audio, I
Re: Matrix 1000 and SQ Midiquest 10 XL HELP
2014-03-29 by <laurent.lecatelier@...>
Hi, I built a hardware controller for Marion MSR2, Tetra, the Shruthi etc ... If a french user can send me a matrix 1000 for a few days, I can try to make a
Re: [oberheim] Re: Matrix 1000 and SQ Midiquest 10 XL HELP
2014-03-29 by Daniel Forró
Years ago there was such programmer on the market, see here: http://www.matrixsynth.com/2006/10/access-matrix-1000-programmer.html Daniel Forro On 29 Mar,
Re: Matrix 1000 and SQ Midiquest 10 XL HELP
2014-03-29 by <h3pooo@...>
Where can I get the Obi MagiX6000 controller? :)
Re: Matrix 1000 and SQ Midiquest 10 XL HELP
2014-03-29 by <repeatedviewing@...>
Is that a cruel joke? A controller like that would be fantastic, spill the beans fella.
Re: [oberheim] Re: Matrix 1000 and SQ Midiquest 10 XL HELP
2014-03-28 by James Meagher
Have you looked at the KiwiTechnics patch editor? Worth the $ if you have other synths it can control. I am currently using it to control my MKS70, MKS50, K3M,
Re: Matrix 1000 and SQ Midiquest 10 XL HELP
2014-03-28 by <GOODFELLOWPAT@...>
Yes, +1 for the source of those hardware controllers. I m having a heap of fun generating random patches with MQ, but a reasonably priced dedicated controller
RE: [oberheim] Re: Matrix 1000 and SQ Midiquest 10 XL HELP
2014-03-28 by tim p
Where can you get hold of those controllers please ?! 😁 ________________________________ From: Marcelo Malmierca Sent:
Re: [oberheim] Re: Matrix 1000 and SQ Midiquest 10 XL HELP
2014-03-28 by Marcelo Malmierca
Forget software faulty editors and windows hang ups. Get a hardware editor for your Matrix ! https://www.dropbox.com/s/xlpbk4e40mopt7x/Item%20197.jpg Marcelo
Re: Matrix 1000 and SQ Midiquest 10 XL HELP
2014-03-28 by <GOODFELLOWPAT@...>
For anyone reading.... I had, and still having this same issue.. but I m making headway. I ve found it helps to store thepreset you want to edit into the
Re: [oberheim] Re: Matrix-1000 Updated V1.1.3 firmware for better sysex control.
2014-03-27 by F.Manduca
Also interested, if it is the very last one firmware.I live in Tuscany, Italy, ZIP Code 51100. Would it be possible? Thanks a lot in advance.
Re: Faulty Matrix 6r (or faulty user) ?
2014-03-27 by <GOODFELLOWPAT@...>
Hey Guys, Yea, I did some further researching directly after I posted this message... and yep, I figured out the Outputs. The presets it came with from the
Re: Faulty Matrix 6r (or faulty user) ?
2014-03-27 by <wesknick@...>
It s sounds like it s functioning correctly. Welcome the Matrix 6. If you read the manual further you ll learn that output from the right output is only
Re: [oberheim] Faulty Matrix 6r (or faulty user) ?
2014-03-27 by Jon Carroll
No, it sends mono out. if you split it, the second tone comes out the right, iirc. ... From: To: Sent:
Faulty Matrix 6r (or faulty user) ?
2014-03-26 by <GOODFELLOWPAT@...>
Hey Group, So I ve just acquired a Matrix 6r. I ve set it up (in Ableton) and it would appear to be only Outputting audio on the Left channel. I ve already set
Re: Matrix-1000 Updated V1.1.3 firmware for better sysex control.
2014-03-25 by <synthparts@...>
Hi, I can provide you with the ROM. Where are you located? Doug synthparts.com
Re: [oberheim] Re: Oberheim OB-Sx EPROM Data
2014-03-25 by John Leimseider
There are several versions of the OBSX ROMs. Some of them use the switch on the back with 2 banks of sounds, some don t... I can read and write 2708s f
Re: Oberheim OB-Sx EPROM Data
2014-03-25 by <synthparts@...>
Hi, the OB-SX used old triple-supply 2708s so I can t read them but I have a spare set of working ROMs I can provide you with... Doug synthparts.com
Re: Matrix-1000 Updated V1.1.3 firmware for better sysex control.
2014-03-22 by <jakobole@...>
Hello everybody I m expecting a Matrix 1000 to land on my dorstep soon. Is it still possible to get hold of a 1.13 ROM? Cheers and TIA
R: Re: [oberheim] Matrix-6 display replacement questions/issues
2014-03-21 by ste.mari@libero.it
I sure need two units for my M6 e M6rMartin from Italy ... Da: daveogarf@yahoo.com Data: 19/03/2014 21.32 A:
Oberheim OB-Sx EPROM Data
2014-03-20 by Patrick Edwards
Anybody have a working OB-Sx and an eprom burner who is willing to copy and send the data to me? My Sx freezes with the first four patch LEDs lit when it is
Re: [oberheim] Matrix-6 display replacement questions/issues
2014-03-20 by Daniel Forró
Hi, Bob, thanks for your effort, here is my answer. ... No problem. And yes, non backlit or EL backlit display shouldn t be used... ... Not at all. ... For me
Re: [oberheim] Matrix-6 display replacement questions/issues
2014-03-19 by Dave Garfield
Hi, Bob & other M-6/-6R owners! BOB! That all sounds great. Just for information s sake, here are my responses to your questions: 1.) A more expensive OLED
Re: [oberheim] Matrix-6 display replacement questions/issues
2014-03-19 by Bob Grieb
Hi Dave and anyone else who has an interest in this, I am willing to design a little interface from the Matrix display signals to some other type of
RE: [oberheim] tim
2014-03-17 by tim p
Sorry for the spam. This hotmail account of mine has now been recovered from the mailbot that hacked it. ________________________________ From:
tim
2014-03-17 by tim
http://ozbilekhosting.com/rp/xwvaevjd.czpuz