Yahoo Groups archive
Messages
Page 51 of 564 · 28179 messages matched
2014-09-24 by David Kellett
Yeah I'm mixing the control voltages before the uScale. And the uScale is good. I'm only scratching the surface of it so far - basically making it quantise to an F pentatonic scale at the moment. But it is great that I can add notes into that or take them out very simply on the f
2014-09-24 by David Kellett
Yeah I have a couple of the Doepfer cables. I'm thinking about a box to take the individual triggers per step out of the SQ10 so that they are straight converted to Eurorack triggers that are then available at the other side of the box. But also to have a switch for each trigger
2014-09-24 by Nicholas Keller
We were assuming an A-156 Dual Quantizer, but he is using an Intellijel uScale. In this case, either seq and S&H must be mixed pre uScale or S&H must be trimmed and patched to Scale input. I've never used a uScale, but it looks quite interesting! Nick Sent from the future > On Se
2014-09-24 by istari
Hi i use also a SQ10 with my euro rack. to trigger the sq10 from the A100 there is a spezial cable available by doepfer that changes the different gate phases. i also used the 0/1 conversion from the doepfer logic module or the trigger modifier for this ( you can also use a simpl
2014-09-24 by Florian Anwander
Hello I could imagine, that the Mixer puts a too high load on the S&H-Output. I'd try the following setup SequenceFromVolta into A-156 "Quantizer 1"-CvIn RandomVoltage into A-156 "Quantizer 2"-CvIn Quantizer 1 CvOut in A-138 In1 Quantizer 2 CvOut in A-138 In2 A-138 Out into VCO-C
2014-09-24 by David Kellett
It's a uScale Intellijel quantiser and the values are such that I'm not dropping the voltage into negative and getting low Cs. Sorry about the foot!! Hope it's not too painful. I sympathise as I had a car accident 2 1/2 years ago and still in a lot of pain. But the bright side is
2014-09-24 by Nicholas Keller
As per my last reply where I suggest monitoring the 3 outputs of you original patch..... If you have a DMM with DCV setting, you could advance each step manually and measure the outputs to verify that all three are in fact different and that the combined quantizer output is diffe
2014-09-24 by Nicholas Keller
After my last reply, I re-read your original post and the other comment. I see that he does say that the resulting sequence would be half the range of the original, and I see that you specify that your goal is a sequence that is never the same. I think your original setup was bas
2014-09-24 by David Kellett
It is each note to be affected not each bar. David www.movingisliving.co.uk Sent from my iPhone > On 24 Sep 2014, at 14:01, Nicholas Keller maq163x2@gmail.com [Doepfer_a100] wrote: > > David > > I'm still not sure I understand what you want. Do you want each bar to be transposed
2014-09-24 by Nicholas Keller
David I'm still not sure I understand what you want. Do you want each bar to be transposed by a random amount? Or do you want each individual step to be a random value within a certain range from the active SQ-10 step value (so that if S+H range = -/+3 semitones, and SQ-10 sequen
2014-09-24 by David Kellett
I will try thy when I'm home, David www.movingisliving.co.uk Sent from my iPhone > On 24 Sep 2014, at 10:05, domenicocollacciani@yahoo.it [Doepfer_a100] wrote: > > Hi Nicholas, > > > I think you should use linear VCA A-130 instead of linear mixer A-138 sending the original sequen
2014-09-24 by David Kellett
My original sequence is supplied by a Korg SQ10 - the triggers not being compatible are coming from elsewhere. I want a basic shape to the sequence with a slight and varying remove from it. David www.movingisliving.co.uk Sent from my iPhone > On 23 Sep 2014, at 15:13, Nicholas Ke
2014-09-24 by domenicocollacciani@yahoo.it
Hi Nicholas, I think you should use linear VCA A-130 instead of linear mixer A-138 sending the original sequence to In 1 and the output of the S&H to cv2 . With gain at 5 and cv2 at 0 you should get a stable basic sequence of voltages (with lower voltages, being the amp ratio 0,5
2014-09-23 by Nicholas Keller
Hello David. You are speaking my language. Let's back up a bit. You said that the S+H is being triggered in time with the original sequence. In this case, the original sequence basically becomes unnecessary as for each step in the sequence, another voltage is added. You are corre
2014-09-23 by David Kellett
Hi, I'm trying to create a randomised sequence. I have an analog sequence of volta going into a quantiser via an A138 Lin. In another channel of the 138 I have a S&H voltage. The S&H is derived from an A148 clocked by the same trigger as the sequence and with the sample being Ran
2014-09-19 by doubleopards@hotmail.com
Thanks for the update Dieter! Really looking forward to this module. Just got the A-100PB in the post yesterday and have some gaps to fill... Best, Jon
2014-09-12 by David Kellett
Very good!! Yes you are right base not bass!! My spelling is not my best characteristic!! And thanks about the VCA advice, David www.movingisliving.co.uk Sent from my iPhone > On 12 Sep 2014, at 12:04, "Florian Anwander fanwander@mnet-online.de [Doepfer_a100]" wrote: > > Hello Da
2014-09-12 by Florian Anwander
Hello David Am 12.09.2014 12:38, schrieb David Kellett davidkellettwoulf@yahoo.com [Doepfer_a100]: > I'm going to be buying a monster bass This is a monster bass: http://www.outdoorcentral.com/articles/wp-content/uploads/2009/03/20090303003.jpg I think, you want to by a monster b
2014-09-12 by David Kellett
I'm going to be buying a monster bass in the next few weeks and some modules to add to my Basic System Two. I will have enough modules to have 3 or 4 independent voices if I want to. I'm looking at what would be best at the end of the voice - a VCA controlled by an envelope. I th
2014-09-07 by David Kellett
Yeah I know!! But this was a forced upgrade - flood, fall and computer death all involved so had to have a new set up. There is hope that Apple / Motu will sort it out and then all will be fine with Midi again. But until then I'm really enjoying the simplicity of volts/octave and
2014-09-05 by Scott Rogers
This wont be helpful at all but just FYI: That's a big fear I have when I upgrade! But after upgrading to Windows 7 my Midisport 8x8 is still working perfectly and I've heard it will work with Win 8 as well. Whew!! Scott www.scottfromcanada.com At 10:10 AM 9/5/2014, you wrote: I'
2014-09-05 by David Kellett
I've been having a bad experience with MIDI recently. My old Midisport 8x8's worked fine - but a new computer and there are no drivers for them with latest Mac. So I looked around and found the NOTU Midi Express 128 - all the info says they work with latest Mac. But they don't!!
2014-09-05 by Florian Anwander
Hello David Am 23.08.2014 12:38, schrieb David Kellett davidkellettwoulf@yahoo.com [Doepfer_a100]: > And speaking of the SH101 - it's my only v/ octave synth (others are > Korg MS series and hertz/volts). What keyboards do people find > useful? What I'd like is is simple keyboard
2014-09-01 by yahoo@doepfer.de
> Is the A-190-5 still under development? I'm currently using a > Vermona Quad Midi Interface and the version of the proposed > A-190-5 looks like it would give me the same functions in > considerably less space. I'm currently maxed out in that department. The A-190-5 is still un
2014-08-26 by Zoë Blade
> There just happens to be a full set on eBay right mpw but they want £1000GB! Thank you! A few months of waiting and not seeing any, then as soon as I post this message, there's one!
2014-08-26 by JS Home
There just happens to be a full set on eBay right mpw but they want £1000GB! Jonathan Shapero Sent from my iPhone > On 25 Aug 2014, at 17:05, "Zoë Blade zoe@bytenoise.co.uk [Doepfer_a100]" wrote: > > Hi! > > I know this is a bit of a long shot, but does anybody (preferably in Eur
2014-08-26 by david.salter@thomsonreuters.com
Welcome :) * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * David Salter Senior Consultant Solutions Services EMEA North Thomson Reuters O +44 (0)20 7542 2402X 52402 M 07990562402 david.salter@thomsonreuters.com thomsonreuters.com From: Doepfer_a100@y
2014-08-26 by Zoë Blade
Thank you! Perfect timing. :)
2014-08-26 by david.salter@thomsonreuters.com
Hi Zoe, A complete vocoder system is on ebay at present Not mine BTW http://www.ebay.co.uk/itm/Doepfer-Analogue-Analog-Vocoder-Complete-OOP-RARE-/231315990688?pt=UK_Musical_Instruments_Pro_Audio_Synthesisers_CV&hash=item35db81e8a0 David · · · · · · · · · · · · · · · · · · · · · ·
2014-08-25 by Zoë Blade
Hi! I know this is a bit of a long shot, but does anybody (preferably in Europe) have any of the more obscure vocoder modules that they'd like to part with, or even a complete set? Thanks, Zoë.
2014-08-24 by lunar_asylum@yahoo.com
Is the A-190-5 still under development? I'm currently using a Vermona Quad Midi Interface and the version of the proposed A-190-5 looks like it would give me the same functions in considerably less space. I'm currently maxed out in that department.
2014-08-24 by David Kellett
I will. I think that the chips I've found on eBay are ok. It looks as though the 2nd and 3rd four digit numbers are probably date / batch numbers. I'm waiting to hear back from the seller of those before I order anything. And I'll see if Doepfer can tell me anymore tomorrow. Davi
2014-08-24 by David Kellett
I have taken the filter module and the envelope module out - checked the wiring and plugged them back in - no difference in performance. Even tried different power sockets on the rail in the system to make sure there wasn't a dodgy one. No luck :-) David www.movingisliving.co.uk
2014-08-24 by fleur.de.florence01@gmail.com
It is a pleasure , let us know about the status of your filter :-)
2014-08-24 by Nicholas Keller
I didn't know you had purchased this BS2 second hand and from eBay. Have you made sure the modules are all plugged in to the power bus? Some circuits can pass audio without being powered. And companies that sell electronics on eBay are not necessarily aware of how they work and w
2014-08-24 by David Kellett
Thanks for the help. I shall see if I can get the chip I need. David www.movingisliving.co.uk Sent from my iPhone > On 24 Aug 2014, at 13:25, "fleur.de.florence01@gmail.com [Doepfer_a100]" wrote: > > yes that is all you need to do, for cons I have no idea of the strength he neede
2014-08-24 by fleur.de.florence01@gmail.com
yes that is all you need to do, for cons I have no idea of the strength he needed, but when the introduction of the new chip well check it is properly nested so that it did not loose connections
2014-08-24 by David Kellett
So you lever the chip out of its base and slot the new one in? I thought that was probably it but it have no idea how much force needs to be applied. I'm still trying to find if the CEM 3379 that I have found is compatible. David www.movingisliving.co.uk Sent from my iPhone > On
2014-08-24 by David Kellett
I've found a few CEM3379's on eBay but they do not have the same numbers after the 3379 part as the one in the A106-6 - would they be compatible? David www.movingisliving.co.uk Sent from my iPhone > On 24 Aug 2014, at 12:13, "David Kellett davidkellettwoulf@yahoo.com [Doepfer_a10
2014-08-24 by David Kellett
Where would I get a CEM 3379 (I'm in the UK) - and is it really easy to replace? I've never soldered anything in my life!! David www.movingisliving.co.uk Sent from my iPhone > On 24 Aug 2014, at 11:59, "fleur.de.florence01@gmail.com [Doepfer_a100]" wrote: > > Hi David, I think yo
2014-08-24 by fleur.de.florence01@gmail.com
Hi David, I think you 're good to change the CEM 3379 so really nothing happens when you turn the Q and Freq buttons
2014-08-24 by David Kellett
I would patch the bender cv by adding it to the main cv for pitch - to both OSC or to one using synch to make some interesting harmonics. Or patch it to filter etc. just seemed more useful if bit hard wired to the keyboards cv all the time. David www.movingisliving.co.uk Sent fro
2014-08-24 by David Kellett
Yep I was going in from the front panel. And wiggling didn't seem to help in afraid. It could then still be a dodgy socket - I had bit thought that that could short the system buss too. David www.movingisliving.co.uk Sent from my iPhone > On 23 Aug 2014, at 12:37, "Nicholas Kelle
2014-08-24 by David Kellett
As I wrote before I recently purchase my A-100 Basic System 2 from eBay. I'm taking a Sawtooth out to the A106-6 audio in. Only from the 4L can I get any sound and this is with Lev at about 8.5 and above. Even then the Frq and Q make no change to the sound and it seems to me that
2014-08-23 by Nicholas Keller
I'm also a bit curious how you plan to patch a lone bender CV..... One of two VCOs, filter cutoff? I too have an SH-101 as well as several MIDI/CV convertors, but I most often use a Doepfer joystick for "performing" CV sweeps rather than set up a midi signal. Doepfer does make a
2014-08-23 by Nicholas Keller
Are you using the front panel gate input of the A-140 as opposed to the system bus? Try wiggling the plug going into the socket. Sometimes when my A-100 modules aren't responding, it is just a poor connection at the socket. If trying to use the system bus, it could still be the s
2014-08-23 by David Kellett
Hi, I'm wondering if there are any other A100 users in my area? I bought my A100 Basic System 2 from eBay. One of the a140's is not working. The seller has ordered a new one for me - but I'm wondering if the not working one can be fixed. It is not triggering so hard to tell how b
2014-08-15 by yahoo@doepfer.de
The A-155 uses only CMOS standard circuits of the 4000 series (CD4011, CD4024, CD4051, CD4053) and standard operational amplifiers (TL0xx series). Best wishes Dieter Doepfer > -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com [mailto:Doepfer_a100@yahoogroups.c
2014-08-14 by mark@markfrancombe.com
Wow, it was a long time since last message and I still haven't gotten the 155 fixed.Im sure it is old, I bought it along time ago, and then it was second hand!Regarding sending it to Doepfer to be fixed. Im in Norway, which strictly is not in the EU. However I did send an item to
2014-07-30 by Unknown
" Content-Transfer-Encoding: quoted-printable Mime-Version: 1.0 (1.0) X-Originating-IP: 98.138.91.172 X-eGroups-Msg-Info: 1:12:0:0:0 Subject: A-147 VCLFO source of interferences X-Yahoo-Group-Post: member; u=480629020; y=wu3pWvdKOXHDcZmhwdXm47_h4as1Wxp0omSBGUKdKg1YUoKRNjgByXiV X-