Yahoo Groups archive
Messages
Page 62 of 564 · 28179 messages matched
2013-11-07 by Zoë Blade
You only need to add an A-185-1 in one row of the second case, then use a little wire from Doepfer inside the case to connect the two bus boards. (This is assuming you want to send the same CV and gate signals to both rows of the second case.)
2013-11-07 by karelvanbezooijen@yahoo.com
Thanks guys for all your reactions! At this moment all three A111 are in the top row. Best is probably to put one in the bottom row. Then add an A185-1 in both rows and connect them to the A190 in the other cabinet. I think I'll just buy a few and try them out, see and hear what
2013-11-07 by Nicholas Keller
James is right. It's not terribly difficult to do, and in a few rare cases the pins are not connected by a trace. I've done it with a drill as he mentioned, a Dremel tool actually with a 3/32" or 1/8" drill bit. I just drilled through the trace, but not necessarily all the way th
2013-11-07 by James Husted
The conversion of modules takes a little DIY skills but is typically not that hard to do. All the jacks that Doepfer uses are normalizing jacks. You look at the Gate or CV input jack and see if the normalizing leg of the tip connection on that jack is connected to anything. Often
2013-11-06 by Zoë Blade
Ah, fair enough. Are plans for such mods available anywhere online? I could do with giving my A-142 bus-based gate in... (At least, I'm assuming it doesn't have it. The Molex connector my partner hooked up doesn't currently support CV/gate either, heh... And I thought my synth wa
2013-11-06 by James Husted
Oh I'm not disappointed in Doepfer modules! I have very many of them. I'm disappointed that hardly any of them use the CV/Gate bus. From the Doepfer website: some modules can pick-up the CV signal (e.g. A-110 , A-111-1 , A-111-5 , A-143-4 ) from the bus depending on the jumper se
2013-11-06 by Zoë Blade
I connect my G3 bus to my G6 bus by way of a Molex connector that my partner rigged up, but don't tell Dieter Doepfer. ;) > There are VERY few modules that connect to this bus which is very disappointing. Seriously, "disappointing" is the last word I'd use to describe any Doepfer
2013-11-06 by James Husted
I have a A-185 in each of my cases (four of them) and the internal buses are linked so both rows get fed. I don't have any modules talking to the bus directly because you never want to have two sources using the bus at the same time. I plug the A-190 into the A-185's input when I
2013-11-06 by Zoë Blade
Brilliant! If the signals come out of the 190 into both the bus and the front at the same time, and you only have two oscillators in that first case, then yes, you'll only need an 185 in the second case, the first is already fine. Excellent! ^.^
2013-11-06 by Scott Rogers
Just to answer the question: yes, if you plug cables into the cv/gate outputs on the front of the 190 it still sends those signals to the buss. So, right now I have my envelope generators on the same buss as the 190 and they get the gate signal through the buss. But I also take t
2013-11-06 by Zoë Blade
Hiya! I'll have a go at answering this too. Someone please correct me if I'm wrong. When you use the front pitch and gate outputs on the A-190, does it still send the signals to the bus as well, or are they mutually exclusive? If it still sends to both, then yes, what you suggest
2013-11-06 by Nicholas Keller
Just using a multiple isn't quite the same as the A-185 is buffered. Nick > On Nov 6, 2013, at 1:26 AM, "squidb0i" wrote: > > If I understand the docs correctly, you need a 185-1 in each case to bridge between communication lines on the power bus bar for each case. > > Obviously,
2013-11-06 by Nicholas Keller
I don't have an A-185, but I think you are correct. The A-190 should provide CV/Gate to Case 1 (only the modules in the same 3U row as the A-190, unless you have the extra cable to connect your bus boards). The sockets on the A-190 can send the signals to the other case's A-185,
2013-11-06 by squidb0i
If I understand the docs correctly, you need a 185-1 in each case to bridge between communication lines on the power bus bar for each case. Obviously, one can also simply mult the control voltage as needed normally, with patch cables, and run to each oscillator, for the same effe
2013-11-06 by karelvanbezooijen@yahoo.com
Please tell me if I'm right or wrong. I have a few cases with modules: Case 1: standard basic system 2 with 2 x VCO 110 and A-190 Case 2: another case with 3 x VCO 111 plus A-141 VCADSR. In order to control Case 2 with the same gate and CV from the A-190 I only need an A-185-1 in
2013-11-04 by Zoë Blade
> All this talk about the A-132-3 got me thinking about it, but when I looked at the web site price list I found there is no link to the product page. Is it still available? It looks like it *was* only available while stocks last, then Doepfer redesigned it to no longer use a rar
2013-11-04 by Scott Rogers
All this talk about the A-132-3 got me thinking about it, but when I looked at the web site price list I found there is no link to the product page. Is it still available? Scott At 03:08 PM 11/4/2013, you wrote: > Indeed, I had totally overlooked the A132-3 which seems an excelle
2013-11-04 by Zoë Blade
> Indeed, I had totally overlooked the A132-3 which seems an excellent alternative to adding a separate A130 and A131. I swear by the A-132-3, for what it's worth. It lets you add velocity sensitivity if you use its two parts in serial. And if you don't need velocity sensitivity,
2013-11-04 by nicholas.buckley@ntlworld.com
Hi Florian, Thank you very much for your extremely clear explanation - I'll certainly be including one or more dedicated VCAs now! Indeed, I had totally overlooked the A132-3 which seems an excellent alternative to adding a separate A130 and A131. Best wishes, Nick ---In Doepfer_
2013-11-03 by Florian Anwander
Hello Nick The A-101-2 contains a exponentiator circuit, but an opto coupler does not have an exact response curve. That means: the A-101-2 will be "something similar as exponential". But there is another reason why you should have a OTA based VCA: Opto couplers are slow. You nev
2013-11-02 by nicholas.buckley@ntlworld.com
Hi everyone, I'm preplanning my first A-100 purchases and I expect the A101-2 to be included. When this module is operating in VCA mode, is the response Linear ( as in A-130 ) or exponential ( as in A-131 ) ? The reason for asking is that, unless I'm much mistaken, I could consid
2013-10-30 by syndromeda@telenet.be
For sale from Belgium: Doepfer A-113 Subharmonic Generator - 180 euro. Not used, only tested, and does not what I thought it should do (creating harmonics as for instance a Kawai K5000S), so I have to RTFM before I buy....;-) I also have the needed 5 Volt power supply (A-100AD5)
2013-10-28 by Pieter Volger
Hiya, For sale from Germany worldwide: Doepfer A-155 (used only a few times) 215,- Euro Doepfer A-143-2, 145,- Euro both modules are fully functional and have only the usual screwhole markings. plus shipping! Please contact me off list!!
2013-10-26 by maq163x2@gmail.com
http://niroke.blogspot.com/2013/10/input-to-comparator-mod-for-doepfer-119.html In this blog post, I show and describe how to do the mods. The mod adds a socket through which the Env Out or Env.Follower Out is routed, so that an external signal (LFO, Sequencer, Min/Max, Random, e
2013-10-24 by yahoo@doepfer.de
> what s the correct fuse for the 1200mA i just upgraded from 650mA? > sold it but the guys says i dosent work, last thing i did before > ship it to him was to check if it worked, and it did.. soooo... > the new 1200mA box i bought for it last month, i really dont want > this to
2013-10-24 by Peter Sedin
what s the correct fuse for the 1200mA i just upgraded from 650mA? sold it but the guys says i dosent work, last thing i did before ship it to him was to check if it worked, and it did.. soooo... the new 1200mA box i bought for it last month, i really dont want this to be broken
2013-10-23 by Rupert Lally
Hi, I've just bought myself the Doepfer a-100 basis system mini, plus a few additional modules in a P6 case and I have a couple of (probably obvious) questions. Firstly, when I trigger the modular via the A190 midi cv interface, there is a click that precedes any envelope sent ou
2013-10-21 by sweetsynthchuck@yahoo.com
Thank You Mr Doepfer, I have just sent a email now. ---In Doepfer_a100@yahoogroups.com, wrote: > Hi does any one know the samplerate and bitrate specs of this device? > i checked the site but the specs are not published. > > Thanks Please contact Christian Assall ( software@... )
2013-10-21 by yahoo@doepfer.de
> Just became aware of the new case announcement. > > Looks very useful! I appreciate that the front section is nice and deep. > > I would like to know though how long a power cable is required for the > modules in the front, given that the bus board is at the back. > > > cheers,
2013-10-21 by achtung_999
Dear Loren, Why not start a new topic in the list for that announcement. Now it is obscured in another thread. grtz Ernst On Mon, Oct 21, 2013 at 10:31 AM, yahoo@doepfer.de > wrote: > Hi does any one know the samplerate and bitrate specs of this device? > i checked the site but t
2013-10-21 by Os
Just became aware of the new case announcement. Looks very useful! I appreciate that the front section is nice and deep. I would like to know though how long a power cable is required for the modules in the front, given that the bus board is at the back. cheers, os. http://www.do
2013-10-21 by yahoo@doepfer.de
> Hi does any one know the samplerate and bitrate specs of this device? > i checked the site but the specs are not published. > > Thanks Please contact Christian Assall (software@doepfer.de). He programmed the firmware of the A-189-1 and knows such details. Best wishes Dieter Doe
2013-10-21 by Loren Nerell
My apologies if this request is off base but I have an odd request for of all my friends here on Doepfer list. I recently had the great pleasure of composing the music to a video on the art of Trang Le. Her painting 111,978 is an incredible and important work on the Iraq war. The
2013-10-21 by sweetsynthchuck@yahoo.com
Hi does any one know the samplerate and bitrate specs of this device? i checked the site but the specs are not published. Thanks
2013-10-20 by fytz_72@yahoo.fr
hi every body for sale Analogue Solutions SY02 : 80 euros Doepfer A130 : 30 euros I can send photos I live in France pay pal accepted with 3% fees sending price for the buyer Please contact me off liste GEORGES
2013-10-02 by Scott Rogers
Yes. He said one of the modules took a long time. He had also mentioned to me earlier that things would be delayed in the summer because people were on vacation etc. Also something about a 2 week shut down. So I expected it to be a bit longer, although this was only my second ord
2013-10-02 by yahoo@doepfer.de
yahoo@doepfer.de or hardware@doepfer.de Best wishes Dieter Doepfer > -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com > [mailto:Doepfer_a100@yahoogroups.com]Im Auftrag von Phil a > Gesendet: Mittwoch, 2. Oktober 2013 12:19 > An: doepfer_a100 > Betreff: Re: AW
2013-10-02 by Phil a
Thanks for your understanding. To which email address should I send it off-list then ? Regards, Phil On Wed, Oct 2, 2013 at 9:04 AM, yahoo@doepfer.de > wrote: > I'm in France but I'm talking from experience, that's how long it > will take unfortunately. > Thanks for the reference
2013-10-02 by yahoo@doepfer.de
> I'm in France but I'm talking from experience, that's how long it > will take unfortunately. > Thanks for the reference of the switch I will see if I can find it. > In case anyone on the list have one for spare and would be > willing to ship one to me I would be very thankful.
2013-10-02 by yahoo@doepfer.de
> Consider yourself lucky! I'm in Toronto and it just took 2 and a > half months to get 6 modules! I just ordered 2 more and I doubt > I'll see them before November. But luckily I have learned > patience in my old age. > > Also I have to say I'm glad to see that Doepfer is so bus
2013-10-01 by Scott Rogers
Consider yourself lucky! I'm in Toronto and it just took 2 and a half months to get 6 modules! I just ordered 2 more and I doubt I'll see them before November. But luckily I have learned patience in my old age. Also I have to say I'm glad to see that Doepfer is so busy. 15 years
2013-10-01 by Phil a
I'm in France but I'm talking from experience, that's how long it will take unfortunately. Thanks for the reference of the switch I will see if I can find it. In case anyone on the list have one for spare and would be willing to ship one to me I would be very thankful. I would pa
2013-10-01 by yahoo@doepfer.de
> Regarding the switch, so sad for such tiny orders there is no > shop online. It will take at least 2 weeks for my local > representative to get a shipment from your offices and probably 1 > additional week for the switch to arrive here... > > Regards, > Phil It depends upon you
2013-10-01 by Phil a
Thanks for your reply. Regarding the switch, so sad for such tiny orders there is no shop online. It will take at least 2 weeks for my local representative to get a shipment from your offices and probably 1 additional week for the switch to arrive here... Regards, Phil On Tue, Oc
2013-10-01 by yahoo@doepfer.de
> Hi, > > I heard from Arturia that the Minibrute has a 12V gate output, so > it seems that this is enough for the ARP. > I tried the DT on some eurorack envelopes and it worked properly. > So I guess this is a slight incompatibility issue with the ARP gate. > Since the MiniBrute
2013-10-01 by Phil a
Hi, I heard from Arturia that the Minibrute has a 12V gate output, so it seems that this is enough for the ARP. I tried the DT on some eurorack envelopes and it worked properly. So I guess this is a slight incompatibility issue with the ARP gate. Since the MiniBrute delivers 12V
2013-10-01 by Zoë Blade
Hi Dimitri! Welcome, and thank you!
2013-10-01 by wildtek.concept@gmail.com
Hello everyone, Just joined the group since I'm the Q-ONTROL template creator and wanted to thanks those who requested for it. I've never been very sure if it was useful for someone else then me and it was recently proved that yes it is :-) I was working with it no later than yes
2013-10-01 by Zoë Blade
Hiya! > when you mount the tank inside the case I recommend to wrap the tank in two layers of aluminum foil. This eliminates all interferences. At least from my experience ;) Thanks for the tip! I haven't noticed any interference, but that may just be my hearing not being all tha
2013-10-01 by macrodx@yahoo.com
Hi Zoe, when you mount the tank inside the case I recommend to wrap the tank in two layers of aluminum foil. This eliminates all interferences. At least from my experience ;) ---In doepfer_a100@yahoogroups.com, wrote: Hi! In case this is any help to anyone, here's one way (probab