Yahoo Groups archive
Messages
Page 84 of 564 · 28179 messages matched
2012-08-24 by Richard Horsman
Hi It could be a problem with the jack socket below the pot instead of the pot itself. I believe that when a lead is plugged into this the knob becomes an attenuator of this signal. If the socket 'thinks' a cable is plugged in then that knob may be attenuating zero volts so not d
2012-08-24 by Florian Anwander
Hi And one other thing comes to my mind: the switching contact of the socket below the potentiometer might make no contact. Florian
2012-08-24 by Florian Anwander
Hello Am 24.08.2012 15:04, schrieb Janne Gson Berg: > Is the pot itself broken, or is there anything else I should try to pin down the problem? You might try to measure the voltage between the centerpin of the potentiometer and ground. Check, whether this voltage changes, if you
2012-08-24 by Janne Gson Berg
Hi everyone! I have got an A-155 sequencer where one of the pots on the bottom row does not work. At all. In order to try to pin down the error I have swapped the ICs from the top row to the bottom row (http://www.doepfer.de/A100_pictures/doepfer_a155.jpg, the two PCBs with the k
2012-08-23 by yahoo@doepfer.de
> On the A-138d, are both in 1's the same? Using it as an effects > loop, does it matter which I plug into with A100 signal? Are both > mix out's the same? > Thanks in advance > -Matt The input socket pair In1 and the output socket pair are "miniature multiples", i.e. nothing but
2012-08-22 by matthewsimonmelnick
On the A-138d, are both in 1's the same? Using it as an effects loop, does it matter which I plug into with A100 signal? Are both mix out's the same? Thanks in advance -Matt
2012-08-22 by achtung_999
Thanks guys! And yes, 4sound is quite ok Florian. I know both stores in Oslo. But hardly interesting for modular. Another good general store in Oslo is Riff music (close to the Opera building). I had pleasant dealings with the excellent personel there! But they are mainly a guita
2012-08-22 by Florian Anwander
Hello Ernst, Am 22.08.2012 10:10, schrieb marco_zambardi: > Have a look to escape from noise shop. They are based in sweden and > sell online too, i don't know if this avoid import taxes but I think > is the nearest shop to Norway. The official representativ of Doepfer is in loca
2012-08-22 by marco_zambardi
Hi, Have a look to escape from noise shop. They are based in sweden and sell online too, i don't know if this avoid import taxes but I think is the nearest shop to Norway. --- In Doepfer_a100@yahoogroups.com, achtung_999 wrote: > > Hello list, > > I was wondering how many people
2012-08-21 by achtung_999
Hello list, I was wondering how many people from Norway are on this list. There is a slight chance that I'll be moving to Oslo next year. Since I know of the fierce import taxes I was wondering where you guys buy your modules (Swedish shopping?). I have been coming to Oslo for ye
2012-08-15 by sebastien.ehrlich
Hello everyone ! A quick message after being back in the Group. Looking for some euro modules but especially 2x Doepfer A-100 G6 (FR/EU only please) and this list of modules : Plan B : Model 28 Model 24 Model 15 (x2) Model 13 Model 12 Model 11 Doepfer : A199 A-196 A-188-1 A-181 A
2012-08-15 by Zoë Blade
I have an A-199, and this is the little I've worked out about it so far: * It seems to be very quiet. if I plug my VCA's output directly into my breakout box, the signal's very loud. If I plug the A-199 in between them, I'll have to crank up the VCA to compensate. This isn't a pr
2012-08-15 by millerstephen@ymail.com
Hello guys, I had a question for those A-199 Spring Reverb unit owners out there. I own a guitar spring reverb unit built into a solid-state guitar amp, and have tried various other spring reverbs for guitar. I recently bought an A-199 and although I'm very happy with it, I did n
2012-08-14 by Zoë Blade
Excellent, thank you very much! It all makes sense now. :)
2012-08-14 by yahoo@doepfer.de
> Hi again! > > So I'm removing the gate and CV bus access jumpers from my > A-190-3, so I can plug its front outputs into the A-185's front > inputs instead... As the A-190-3 doesn't appear to have any > instructions yet, I'm using the A-190-2 instructions as a guide. > I found
2012-08-13 by Zoë Blade
Hi again! So I'm removing the gate and CV bus access jumpers from my A-190-3, so I can plug its front outputs into the A-185's front inputs instead... As the A-190-3 doesn't appear to have any instructions yet, I'm using the A-190-2 instructions as a guide. I found the "gate bus"
2012-08-13 by skp_pete
well well another nail in the coffin for access virus ti Thanks for your help with this, and sorry to waste your time. The culprit is my access virus ti midi output. i should just presume these days when i have strange events occur that the access is to blame!! the a-190 works fi
2012-08-12 by Zoë Blade
Thanks! My partner who's more up on electronics than me assures me that that all makes sense. :D I'll accept the answer of "lots" then! All the best, Zoë.
2012-08-12 by Zoë Blade
Hi! I gather that if you're sending the same CV signal to more than two VCOs, you need an A-185 to boost the signal... does anyone know how many VCOs you can accurately tune together once you've installed the A-185? Thanks, Zoë.
2012-08-12 by synovatron
Hi Zoë, The A-185 has an output impedance that is effectively zero Ohms so it can drive very many VCOs without affecting scale accuracy. Depending on what you are driving your VCOs from already there may not be a need to use a buffered mult (i.e. A-185) for just a few VCOs if the
2012-08-09 by mark
Cheers, hadn't thought of that either... --- In Doepfer_a100@yahoogroups.com, "Mike and Delonna Hyland" wrote: > > Mark, just thought Iâd suggest another obvious possibility â" if you are using a MIDI or other controller, make sure the pitch wheel is set exactly in center (or
2012-08-09 by PAUL BURTON
That's great news. I'm in the USA. So I'd be dealing with Analogue Haven. (Shawn has always been a great representative by the way) Thanks again! Paul ________________________________ From: "yahoo@doepfer.de" To: Doepfer_a100@yahoogroups.com Sent: Wednesday, August 8, 2012 11:21
2012-08-09 by Sean Ellis
Awesome stuff! To: Doepfer_a100@yahoogroups.com From: os@collective.co.uk Date: Wed, 8 Aug 2012 20:43:14 +0100 Subject: [Doepfer_a100] some gig videos with a largely Doepfer system are here: http://vimeo.com/album/2034691 Enjoy! cheers, os. -- os@collective.co.uk http://twitter.c
2012-08-09 by skp_pete
thanks for the thoughts guys i'll have a play with note off velocity i've been in contact with Matthias and i have a few things to try for trouble shooting
2012-08-08 by Os
are here: http://vimeo.com/album/2034691 Enjoy! cheers, os. -- os@collective.co.uk http://twitter.com/expertsleepers http://www.darkroomtheband.net/ http://www.expert-sleepers.co.uk/
2012-08-08 by yahoo@doepfer.de
> Thanks for the the reply Dieter, but I am not referring to front > panels of the modules themselves, > > but the black Stickers on the top and bottom edge of the portable case like below: > > A-100 ANALOG MODULAR SYSTEM DOEPFER > > Thanks again! > Paul You can get these for fre
2012-08-08 by Florian Anwander
Am 08.08.2012 16:33, schrieb yahoo@doepfer.de: > But another idea came to my mind: maybe note off messages with embedded > velocity values are sent. That is what I meant. To my knowledge Ableton does send noteOff with noteOff-velocity. Florian -- http://fa.utfs.org/
2012-08-08 by PAUL BURTON
Thanks for the the reply Dieter, but I am not referring to front panels of the modules themselves, but the black Stickers on the top and bottom edge of the portable case like below: A-100 ANALOG MODULAR SYSTEM DOEPFER To: Doepfer_a100@yahoogroups.com Sent: Wednesday, August 8, 20
2012-08-08 by yahoo@doepfer.de
> Hello > > one thing comes to my mind: What is the note length of the notes? > > I could imagine that the interface can get difficulties with minimal > note lengthes. > > Florian I don't think that this could be a problem because the velocity value is an integral part of the 3 b
2012-08-08 by Florian Anwander
Hello one thing comes to my mind: What is the note length of the notes? I could imagine that the interface can get difficulties with minimal note lengthes. Florian Am 08.08.2012 14:35, schrieb skp_pete: > > > --- In Doepfer_a100@yahoogroups.com, wrote: >> >>> hello, i've got a we
2012-08-08 by Mike and Delonna Hyland
Mark, just thought I’d suggest another obvious possibility – if you are using a MIDI or other controller, make sure the pitch wheel is set exactly in center (or whatever is “0”). I’ve had mine get a little off before and wonder why I wasn’t in tune. Mike PS Dieter, I really love
2012-08-08 by skp_pete
--- In Doepfer_a100@yahoogroups.com, wrote: > > > hello, i've got a weird issue concerning the a-190 when used > > with the velocity out from CV2. i've had the module for over 2 > > years and its been fine up until now > > > > i'm using the velocity to control the volume on my vc
2012-08-08 by yahoo@doepfer.de
> Hi All, > > Please don't slay me if this has been covered before, but does > anyone know if I can purchase a new set of front panel decals for > an A-100 case? I don't do Eurorack...just Doepfer since the late > 90's and I want to show some pride when playing live. Vanity I > k
2012-08-07 by InLovingJest
Hi All, Please don't slay me if this has been covered before, but does anyone know if I can purchase a new set of front panel decals for an A-100 case? I don't do Eurorack...just Doepfer since the late 90's and I want to show some pride when playing live. Vanity I know, but I lov
2012-08-07 by mark
Thanks to all three replies, I shall get my volt meter out before I start adjusting anything Thanks Mark --- In Doepfer_a100@yahoogroups.com, wrote: > > > I've had my Dark Time for the last year or so and I've just > > checked it with a chromatic tuner. It's playing all notes > >
2012-08-06 by Zoë Blade
Incidentally, for anyone who's tone deaf or tone hard of hearing, you can use a voltmeter to check the voltages coming out of the sequencer. The semitones should all be 0.08(3) volts apart from each other. I described this in more detail over at http://bytenoise.co.uk/CV%252Fgate
2012-08-06 by Florian Anwander
Though Dieter already answered, I jump in here: Am 02.08.2012 23:41, schrieb mark: > It's playing all notes slightly flat. Any idea how to adjust it ? if all(!) notes are playing the same flat, then the overall tuning of the synth has to be adjusted, not the scaling, which Dieter
2012-08-06 by yahoo@doepfer.de
> I've had my Dark Time for the last year or so and I've just > checked it with a chromatic tuner. It's playing all notes > slightly flat. Any idea how to adjust it ? > > Or do I just retune any oscillators it's controlling ? > > Mark There are two trimming potentiometers labelle
2012-08-06 by edward tomlin
Thankyou for the response and explaination. Regards Ed On 6 August 2012 10:47, wrote: > ** > > > > i've noticed this on my a-132-4 > > i'm using mine as 4 separate vca's > > a negative voltage will no doubt close it more, but why the > > design i wonder > > The A-132-4 VCAs have
2012-08-06 by yahoo@doepfer.de
> hello, i've got a weird issue concerning the a-190 when used > with the velocity out from CV2. i've had the module for over 2 > years and its been fine up until now > > i'm using the velocity to control the volume on my vca's . > > i'm essentially getting spikes in volume on so
2012-08-06 by yahoo@doepfer.de
> i've noticed this on my a-132-4 > i'm using mine as 4 separate vca's > a negative voltage will no doubt close it more, but why the > design i wonder The A-132-4 VCAs have an exponential control scale. The A-132-4 information on our website says "The control scale for each VCA i
2012-08-05 by skp_pete
--- In Doepfer_a100@yahoogroups.com, "masterofthelefthand" wrote: > > Hello everyone > > i have started to notice that sound comes through my a132-3 vca even when the gain control is at zero. It is a low volume but quite annoying. Any ideas? > > > Cheers > > ed > i've noticed thi
2012-08-05 by skp_pete
hello, i've got a weird issue concerning the a-190 when used with the velocity out from CV2. i've had the module for over 2 years and its been fine up until now i'm using the velocity to control the volume on my vca's . i'm essentially getting spikes in volume on some notes, or s
2012-08-04 by masterofthelefthand
Hello everyone i have started to notice that sound comes through my a132-3 vca even when the gain control is at zero. It is a low volume but quite annoying. Any ideas? Cheers ed
2012-08-04 by Zoë Blade
Ah, Ceephax... http://afxaventurs.tumblr.com/post/19210758109
2012-08-04 by Bakis Sirros
member deleted! Bakis ________________________________ From: ienni23 To: Doepfer_a100@yahoogroups.com Sent: Saturday, August 4, 2012 3:02 AM Subject: [Doepfer_a100] SPAM! :-( SPAM SPAM SPAM SPAM SPAM SPAM SPAM SPAM LOVELY SPAAAM, WONDERFUL SPAM!!!! seriously, wtf? this kind of cr
2012-08-04 by Bakis Sirros
:-) Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist [Doepfer_a100] group owner www. parallel - worlds - music. com www. facebook. com/ pages/Parallel-Worlds/192093934136476 www. myspace. com/ interconnectedmusic www. myspace. com/ memorygeist www. DiN. org. uk www.
2012-08-04 by christian ienni
i hadn't seen it, but your mention of it sent me to youtube...... holy fucking shitspackle on a stick!!! that is one of the funniest things i've seen in a while! "Obligatory Pigeon"!!?!?!! and the willfully cheesy "video toaster" greenscreen aesthetic... he has a seriously wonder
2012-08-04 by Giorgio
but can we all at least agree that the new ceephax video is fucking great right!!!1111???//// On Aug 4, 2012, at 12:16 AM, christian ienni wrote: > yes, you're right, i overreacted. :-) > > i was already in a bad mood (for other reasons), and when i saw it i was just surprised to
2012-08-04 by christian ienni
yes, you're right, i overreacted. :-) i was already in a bad mood (for other reasons), and when i saw it i was just surprised to see such a thing in this group, which is really more like an extended family for all us modular obsessives and fans of Dieter's work. apologies for the