Yahoo Groups archive
Messages
Page 106 of 564 · 28179 messages matched
2011-09-01 by yahoo@doepfer.de
> Hi, I want put some yellow tube modules in a G6 case that I have > here but as some of you might know they take too much power and > it's recommended not to put more than 4 of them in one 1.2amp PSU > G6 case. ( I want to put 6 of them) > > But I remember reading ( a manual may
2011-09-01 by ricardo
Hi, I want put some yellow tube modules in a G6 case that I have here but as some of you might know they take too much power and it's recommended not to put more than 4 of them in one 1.2amp PSU G6 case. ( I want to put 6 of them) But I remember reading ( a manual maybe) that it'
2011-08-31 by jonas karlsson
Thanks Jonas 31 aug 2011 kl. 11.27 skrev Ton Akveld: > Nice! > > --- In Doepfer_a100@yahoogroups.com, jonas karlsson > wrote: > > > > Hi Group > > > > Check out my new song, all sounds are made with Doepfer modules > except > > the drums that are made wite Analogue Solutions > >
2011-08-31 by Ton Akveld
Nice! --- In Doepfer_a100@yahoogroups.com, jonas karlsson wrote: > > Hi Group > > Check out my new song, all sounds are made with Doepfer modules except > the drums that are made wite Analogue Solutions > > http://www.reverbnation.com/zyntetix > > http://www.facebook.com/pages/Zy
2011-08-30 by yahoo@doepfer.de
> Hi, > > I want to build my own filter just for fun and have already red a > lot about different filter topologies and poles and stuff. But I > can't find any schematics about how to control the filter frequ > just with one mono pot -- since you actually have to change the > cut
2011-08-30 by jonas karlsson
Hi Group Check out my new song, all sounds are made with Doepfer modules except the drums that are made wite Analogue Solutions http://www.reverbnation.com/zyntetix http://www.facebook.com/pages/Zyntetix/169050709836728 Thanks Jonas
2011-08-30 by jesus
Hi, I have a new (had it less than a month) Mint-shape Harvestman Hertz Donut dual oscillator for sale. $300 plus s/h. Contact me by email at gretchenDOTlipkeATcomcastDOTnet. Thanks JDiaz
2011-08-29 by okmog
Hi, I want to build my own filter just for fun and have already red a lot about different filter topologies and poles and stuff. But I can't find any schematics about how to control the filter frequ just with one mono pot -- since you actually have to change the cut-off freq of e
2011-08-26 by Bakis Sirros
hi All, just a reminder, that the Doepfer ASR (analogue shift register) module poll is closing, in 5 days from now! so, take few seconds and vote! here is the link to it:http://launch.groups.yahoo.com/group/Doepfer_a100/surveys?id=13094690 thanks, Bakis. www. parallel - worlds -
2011-08-25 by Zoë Blade
> So far there are no plans for such a module. I will see if there is a chance > to add the required circuitry to A-190-2/3 and to offer revised versions of > these modules. Wow, thank you! If you do ever make such a revision, I'll certainly buy another A-190-3. :D Thanks, Zoe.
2011-08-25 by yahoo@doepfer.de
> > The glide function of the A-190-3 is nothing but an integrated > A-170 (upper > > section). One would need a slew limiter that is controlled by the > > legato/non-legato information (e.g. a voltage controlled switch that > > bypasses the slew limiter in case of non-legato not
2011-08-25 by yahoo@doepfer.de
> In addition to Dieter's reply: > > Some modules can 'write' to the busboard, and some can only 'read' the busboard. > I posted an (up-to-date) list last November at > http://patchpierre.blogspot.com/2010/11/busboard-access.html > > Enjoy! > > Pierre Serné / PatchPierre / http:/
2011-08-25 by Zoë Blade
> The glide function of the A-190-3 is nothing but an integrated A-170 (upper > section). One would need a slew limiter that is controlled by the > legato/non-legato information (e.g. a voltage controlled switch that > bypasses the slew limiter in case of non-legato notes). The A
2011-08-25 by yahoo@doepfer.de
> Just wondered if anyone has come across a comprehensive list of > Doepfer modules that can access the cv and gate bus on the a100 system. > > I've pieced together the A 110,111,190-1,A140 but what other > Doepfer modules. > > Thanks. Plus A-164-1, A-185-1, A-185-2, A-190-2 and
2011-08-25 by yahoo@doepfer.de
> Hi! > > So I've got an A-190-3 MIDI to CV converter, which is really > great... velocity and mod wheel sensitive too, fantastic... the > only thing I can't seem to do with it is have the glide only > apply to overlapping notes. If I set it to mininum, there's no > glide, as I'd
2011-08-25 by Florian Anwander
Hello Zoe, I don't own a 190-2 or 190-3, but as far as I know those don't have a keyed glide function. Florian
2011-08-25 by NetPierre
In addition to Dieter's reply: Some modules can 'write' to the busboard, and some can only 'read' the busboard. I posted an (up-to-date) list last November at http://patchpierre.blogspot.com/2010/11/busboard-access.html Enjoy! Pierre Serné / PatchPierre / http://PatchPierre.blogs
2011-08-25 by Ton Akveld
Dear Dieter, Thank you for your reply. I'll feed the A-145's signal to the oscilloscoop and see if I can detect the change between with or without trigger. Rest assured I study the manuals as good as I can before posting questions to the group. Warm regards, Ton --- In Doepfer_a1
2011-08-24 by Zoe Blade
Hi! So I've got an A-190-3 MIDI to CV converter, which is really great... velocity and mod wheel sensitive too, fantastic... the only thing I can't seem to do with it is have the glide only apply to overlapping notes. If I set it to mininum, there's no glide, as I'd expect, and o
2011-08-24 by James Husted
Typically you use a A-100BC cable ( http://www.analoguehaven.com/doepfer/a100bc/ ) to connect the two busses together. This also connects the left and right sides of each bus together. You can also connect the two bus boards with a standard 16-pin power cable. Just connect it bet
2011-08-24 by Raul
Just wondered if anyone has come across a comprehensive list of Doepfer modules that can access the cv and gate bus on the a100 system. I've pieced together the A 110,111,190-1,A140 but what other Doepfer modules. Thanks.
2011-08-24 by Raul
Great. This is exactly what I needed. Thanks. -Raul --- In Doepfer_a100@yahoogroups.com, James Husted wrote: > > Typically you use a A-100BC cable ( http://www.analoguehaven.com/doepfer/a100bc/ ) to connect the two busses together. This also connects the left and right sides of e
2011-08-24 by yahoo@doepfer.de
> Hi group, > > As I seem to understand, I can safely use the GATE OUTPUT of the > A-190 MCVS as the INPUT for the Reset Trigger of the A-145 LFO. > I connected the two, but I get no result whatsoever. > Can anyone advice? > > Thanks in advance, > > Ton Each positive edge of the
2011-08-24 by Ton Akveld
Hi Jakob, Thanks for the 'thought', I appreciate it. 1. I think you're right on not obtaining the desired result. 2. As I am in the process of 'building' a A-100 system and financial restrictions prohibit me from buying more than one module a month, I didn't get to purchasing a A
2011-08-24 by jakobsweb
Hi Ton, try connecting A-145 reset in with A-160/161 clock outputs for better rythmical results or the output of a A-140 envelope. Not sure if the gate signal itself - even though you may technicly connect - offers the results you are looking for ... just a thought. yours Jakob -
2011-08-24 by Zoë Blade
> Is this true for the second row in a standard mini system. Or do I have to make a connection. I have no oscillators plugged into the second row but just would like to know my options for the future. As far as I understand, each row's bus is separate by default, but it's super-c
2011-08-23 by Raul
Hello group. I have had a Doepfer mini system with the lower 3u occupied with the mini system and upper row with mixed other modules. I hadn't been using the system with much midi before but noticed the cv transmits via the bus to the a110 VCOS in the lower row and the ADSR in th
2011-08-23 by Ton Akveld
Hi group, As I seem to understand, I can safely use the GATE OUTPUT of the A-190 MCVS as the INPUT for the Reset Trigger of the A-145 LFO. I connected the two, but I get no result whatsoever. Can anyone advice? Thanks in advance, Ton --- In Doepfer_a100@yahoogroups.com, "Ton Akve
2011-08-22 by Zoë Blade
In other words, go for it. ;)
2011-08-22 by zaum
Yes, by patching modules in with the patch cord into the main CV or gate jack on the front of the module causes you to you disconnect the module from listening to the bus. Not all the modules that could in theory follow the signals on the bus actually do. It's mostly your more ba
2011-08-22 by Ton Akveld
It seems so :-) Everybody: ThanX! --- In Doepfer_a100@yahoogroups.com, Zoë Blade wrote: > > In other words, go for it. ;) >
2011-08-22 by yahoo@doepfer.de
> -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com > [mailto:Doepfer_a100@yahoogroups.com]Im Auftrag von Florian Anwander > Gesendet: Sonntag, 21. August 2011 21:32 > An: Doepfer_a100@yahoogroups.com > Betreff: Re: [Doepfer_a100] Another newbie question - use
2011-08-22 by yahoo@doepfer.de
> Hello Zoë, > > > If I understand correctly, it's fine to override the bus by > plugging something into the *front* of a module to give it > another gate or CV signal to pay attention to. > basically you are right, but some early modules (don't ask me which > ones) did not use t
2011-08-22 by yahoo@doepfer.de
> hi dieter, > are there any plans to make these with straight connectors at > each end? i'd welcome another colour being available, and happen > to like orange. :) > > regards, > ian c. Sorry - there are no plans for such cables. The main problem is the stock-keeping of too many
2011-08-21 by Florian Anwander
Hello Zoë, > If I understand correctly, it's fine to override the bus by plugging something into the *front* of a module to give it another gate or CV signal to pay attention to. basically you are right, but some early modules (don't ask me which ones) did not use the switching f
2011-08-21 by Ian
--- In Doepfer_a100@yahoogroups.com, "alexandre_bellenger" wrote: > > Hello, > > I just discovered the existence of the orange cable with one angled side. > > Maybe I am coming really late on that topic, sorry. > > How do you use it? Do you find it interesting? > > best, > > Alex
2011-08-21 by Ton Akveld
Thank you, Zoe. I hope someone else can confirm this, else I just plug in the cable and hope for the best :-) Kind regards, Ton --- In Doepfer_a100@yahoogroups.com, Zoë Blade wrote: > > The wording of this confused me for a while too... If I understand correctly, it's fine to ove
2011-08-21 by Josef
Hi, the track Vivaldi_Concerto_Mandolino_RV425 on youtube: http://www.youtube.com/watch?v=I3zHc_aUbvU Enjoy! Josef
2011-08-20 by Zoë Blade
The wording of this confused me for a while too... If I understand correctly, it's fine to override the bus by plugging something into the *front* of a module to give it another gate or CV signal to pay attention to. What you *mustn't* do is feed two different signals into the bu
2011-08-20 by Ton Akveld
Hi group, The manual of the A-190 MCVS states: The gate output % and CV1 output & are automatically connected to the system bus of the A-100, so don't use patch cables to connect these, unless you have cut the links, or wish to connect to a module whose system bus isn't connected
2011-08-19 by Bakis Sirros
thank you Chris for the detailed info! Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist www. parallel - worlds - music. com www. facebook. com/ pages/Parallel-Worlds/192093934136476 www. DiN. org. uk www. vu-us. com --- On Fri, 8/19/11, cbm wrote: From: cbm Subject:
2011-08-19 by cbm
--- In Doepfer_a100@yahoogroups.com, wrote: > At least the gate/trigger converter should be included too (give me input :-) The Buchla pulse is like a combined gate and trigger. The trig level is +10v, and the gate level is 5v. Multiple triggers can be imposed upon a sustaining g
2011-08-18 by NetPierre
Dear Bakis In the first place I would like to say I appreciate all the things you do for this Doepfer A-100 Group. ... and please don't take this message too personal, but i do have a (minor) complaint; Is it really necessary to post all of your 8 personal links every time? Espec
2011-08-17 by James Husted
This seems like a good module for Eardrill's Buchla "ModuleModule" format ( http://www.eardrill.com/modules/ModuleModule/ ) . Something that would go on the Buchla and not in the Doepfer. Doepfer could of course make it and it would be a good foot in the door into the Buchla worl
2011-08-17 by Bakis Sirros
ok, a new poll for this module has been created. it will remain open for 1 month. please, take few seconds and vote! best regards, Bakis. Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist [Doepfer_a100] group owner www. parallel - worlds - music. com www. facebook. c
2011-08-17 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you want Doepfer to produce a 1volt/oct to 1.2volts/oct (Buchla standard) converter module? [in detail: that would transform a standard 1volt/oct cv/gate signal (coming from any midi to cv interf
2011-08-17 by Bakis Sirros
exactly! Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist [Doepfer_a100] group owner www. parallel - worlds - music. com www. facebook. com/ pages/Parallel-Worlds/192093934136476 www. myspace. com/ parallelworldsmusic www. myspace. com/ interconnectedmusic www. mysp
2011-08-17 by Bakis Sirros
great, will create a poll for this, soon. and, yes, a simple gate to buchla type gate+trigger converter, should be included in the same module too. for the Buchla type Trigger+gate signal, i know that it consists of: timing pulses that are +5V (signals with sustain) and +10V (tra
2011-08-17 by York Luethje
It's agonizingly boring to "design" a DC amplifier with 1.20 amplification factor + internets _____ Von: Doepfer_a100@yahoogroups.com [mailto:Doepfer_a100@yahoogroups.com] Im Auftrag von yahoo@doepfer.de Gesendet: Mittwoch, 17. August 2011 09:05 An: Doepfer_a100@yahoogroups.com B
2011-08-17 by Florian Anwander
Hi Dieter > It's agonizingly boring to "design" a DC amplifier with 1.20 amplification factor. :-))) > At least the gate/trigger converter should be included too (give me input :-) I think a two channel converter would be ok: 8 sockets, * 1V/Oct In1 * Buchla-CV Out1 * Gate In1 *