Yahoo Groups archive
Messages
Page 212 of 564 · 28179 messages matched
2008-12-21 by RMC
Hello Two questions really: 1) I've read the PDF manual for this module but I haven't understood it properly. Can I use the A-152 as an analogue shift register with a shift length of more than three stages i.e. upto 8 stages? I understand the T&H or S&H aspects and the 1-8 mux bu
2008-12-21 by Monroe Eskew
Is it possible to build a passive circuit that will round off the edges of a gate signal? I'm not worried about much control over the slope, I just want to smooth it off a bit, and hopefully not have to supply extra power in order to do this.
2008-12-21 by dingfutzer
FS/FT: Doepfer A112 Sampler/Wavetable - $179, A163 VC Divider - $79, A171 VC Slew - $69, MFB Dual AHDSR - $135, Plan B Model 12 Vactrol VCF - $185, Encore Frequency Shifter factory converted & calibrated to Euro rack & voltage standard - $389. 12 Space 12" deep ATA Rack Case - AB
2008-12-21 by Guy Drieghe D.
I'm quite sure they do. The forum and polls are mutually inclusive. :-) _g > yes, but i hope the voting members are reading these group posts > too.... :-) > > Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist
2008-12-21 by Ken
--- In Doepfer_a100@yahoogroups.com, Bakis Sirros wrote: > > phey... all done! > > now vote, please. > > thanks, > Bakis. > > > Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist > [Doepfer_a100] group owner > www. parallel - worlds - music. com > www. myspace. com/ p
2008-12-21 by Ken
Wow.. a lot of polls. I was not involved in many of the discussions but I would like a reasonably priced wavetable osc. The OSC to CV USB converter sounds great. I hate when I'm using max and on the computer I have smooth floating point resolution then I have to squeeze everythin
2008-12-21 by Bakis Sirros
yes, but i hope the voting members are reading these group posts too.... :-) Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist [Doepfer_a100] group owner www. parallel - worlds - music. com www. myspace. com/ parallelworldsmusic www. myspace. com/ interconnectedmusic
2008-12-21 by Guy Drieghe D.
> ok, all fine. > all these are covered by the current poll. ok? > Yes, Bakis. Only wasn't clear about the Z-value, desktop thing and range controls [in the poll]... _g
2008-12-21 by Bakis Sirros
ok, all fine. all these are covered by the current poll. ok? Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist [Doepfer_a100] group owner www. parallel - worlds - music. com www. myspace. com/ parallelworldsmusic www. myspace. com/ interconnectedmusic www. myspace. c
2008-12-21 by Guy Drieghe D.
Yes, exactly. Z = pressure. It is obvious that this module should be a desktop unit, akin to the Kaos pads indeed. Add a joystick and manual gate for additional ehm, joy. XYZ should have range pots, possibly with precise settings (rotary switch?). _guy > i guess Z would be for pr
2008-12-21 by Bakis Sirros
btw, i just noticed that the sh-101 sequencer poll is already created and Open, from September 2008. so, no need for a new one. Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist [Doepfer_a100] group owner www. parallel - worlds - music. com www. myspace. com/ paralle
2008-12-21 by Bakis Sirros
i guess Z would be for pressure... i just made the poll, i did not suggested the specific module idea. so, to the member who suggested the xyz pad module, if you reading this, elaborate please. Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist [Doepfer_a100] group ow
2008-12-21 by Bakis Sirros
ok, maybe i forgot it. Florian, can you remind me the features you want on this, so i can make this poll too? thanks, best regards, Bakis. Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist [Doepfer_a100] group owner www. parallel - worlds - music. com www. myspace. c
2008-12-21 by Doepfer_a100@yahoogroups.com
The following Doepfer_a100 poll is now closed. Here are the final results: POLL QUESTION: Would you like Doepfer to release the module described below? I suggested the module idea to Dieter Doepfer and he suggested I make a poll to see what the community thinks. This poll might r
2008-12-21 by Gdaluz
And the sh101 style sequencer? Thanks Guilherme www.myspace.com/guilhermedaluz -----Mensagem original----- De: Doepfer_a100@yahoogroups.com em nome de Bakis Sirros Enviada: sáb 20-12-2008 22:04 Para: Doepfer_a100 group Assunto: [Doepfer_a100] 15 new polls! phey... all done! now v
2008-12-21 by york luethje
yeah, same here. I must have missed the preceding discussion. y ________________________________ From: Richard Scott To: Doepfer_a100@yahoogroups.com Sent: Saturday, December 20, 2008 9:08:33 PM Subject: [Doepfer_a100] xyz controller poll gotta say i need more info on this before
2008-12-21 by p. hendricks
On 12/20/08 6:08 PM, "Richard Scott" wrote: > gotta say i need more info on this before voting... as a kaoss pad user the > idea of VC output is nice but the idea of a vertically mounted eurorack module > is awful - is this the concept or is it envisaged more like a desktop unit?
2008-12-21 by Richard Scott
gotta say i need more info on this before voting... as a kaoss pad user the idea of VC output is nice but the idea of a vertically mounted eurorack module is awful - is this the concept or is it envisaged more like a desktop unit? and what is the z? pressure sensitivity? more nfo
2008-12-20 by Bakis Sirros
phey... all done! now vote, please. thanks, Bakis. Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist [Doepfer_a100] group owner www. parallel - worlds - music. com www. myspace. com/ parallelworldsmusic www. myspace. com/ interconnectedmusic www. myspace. com/ memory
2008-12-20 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to release a 3-way Crossover / Frequency Splitter module? (features: -input, -two pots for manual crossover frequency control and two inputs for cv control, -three outputs for lo
2008-12-20 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to release a Basic triangle to sine wave shaper module? (It could have Triangle In, Original Triangle Out and the best possible Sine Out that can be achieved. two of them could f
2008-12-20 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you be interested Doepfer to create an: a) improved tri-to-sine converter for A-111-1 (about Euro 15 additional charges) b) temperature compensated exponential generator for the A-143-9 (about Eu
2008-12-20 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to release a VC Arpeggiator module? [Main features: Midi in, (quantized) CV out, VC Gate out (length, clock division), VC input for octave range (1-4 octaves or so ...), VC of re
2008-12-20 by Alex Pearson
I am happy to see my idea in a poll! On Sat, Dec 20, 2008 at 4:26 PM, wrote: > > Enter your vote today! A new poll has been created for the > Doepfer_a100 group: > > Would you like Doepfer to release a VC-Wavetable module with: > smoothly moving animation, melodic waveforms, quan
2008-12-20 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to release a Window Comparator Module? (for info see here: www.ecelab.com/circuit-window-comp.htm ) o yes! o maybe... o no. To vote, please visit the following web page: http://g
2008-12-20 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to release the Tendency Mask Generator Module? [at Sonology institute, is a device which you feed an upper limit and a lower limit as cv inputs (in a doepfer system it could be a
2008-12-20 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to release an Envelope module with 4 levels and 4 rates controls? (Like a DX-7 or the Roland samplers.) o yes! o maybe... o no. To vote, please visit the following web page: http
2008-12-20 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to release a Stereo Parametric EQ module? (A Dual/Stereo Parametric Equaliser, 2 audio inputs, 2 audio outputs +/- 15dB Gain CV controlled, +/- 5V, Q/bandwidth CV controlled, Cen
2008-12-20 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to release a BASE VC-sampler/wavetable module? [with signal A/D-in (on the frontplate), signal D/A-out (on the frontplate), switch for ac/dc coupling, internal ribboncable connec
2008-12-20 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to release an audio Compressor/limiter module? (It is very easy to blow out your speakers when playing with high-Q filters and such. A compressor/ limiter module would be very ni
2008-12-20 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to manufacture a USD to CV/Gate module that will be receiving computer data (in OSC format, or otherwise) and will be translating it, via a fast high resolution D to A converter,
2008-12-20 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to manufacture a USB mouse to CV interface module? (CV out for X and Y and Wheel, with range controls, and two or three buttons. User supplies the mouse or any other USB controll
2008-12-20 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to release a Preamp module? ( Something to drop down the modular to standard line levels. For interfacing your modular with other gear. 1/8" to 1/4", balanced, and XLR. With a ni
2008-12-20 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to release a VC-Wavetable module with: smoothly moving animation, melodic waveforms, quantization capabilities, the ability to run in both AC and DC ? o yes! o maybe... o no. To
2008-12-20 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to release a XY-Z trackpad controller module? (Comparable to Kaos pads or the Voyager's touchpad. Only with dedicated VC and trig/gate outs, and range knobs.) o yes! o maybe... o
2008-12-20 by Oscar Narro
Hi I'm a new member. I found this group through the radiohead one. I'm pretty interested in modular synths but I honestly don't know what they do. I hope to learn a lot from this
2008-12-19 by yahoo@doepfer.de
> as far as I understand the description it is simply a dedicated constant > voltage which represents the velocity value of the last note-on. Same as > possible with CV2 out of the A190. > > Florian That's correct. Dieter Doepfer
2008-12-19 by Thomas Garrison
Hello, I have a few more modules for sale. All of the modules work perfectly and are in excellent / mint condition besides the slight circle left from mounting them. They each come with rack screws and ribbon cable. I'm located in Seattle, WA but will ship worldwide. Shipping wil
2008-12-18 by Florian Anwander
Hi Monroe > On the A100CGK, what is the shape of the velocity output? Is it a > gate whose level depends on how hard a key is pressed? Or does it > actually output something like an attack phase of an envelope? If it > does an attack phase, then what comes next, sustain, or drop
2008-12-18 by Monroe Eskew
On the A100CGK, what is the shape of the velocity output? Is it a gate whose level depends on how hard a key is pressed? Or does it actually output something like an attack phase of an envelope? If it does an attack phase, then what comes next, sustain, or drop to zero? Thanks, M
2008-12-18 by Laurie Biddulph
Hi, Another option is hat I am shortly to release a 4-way busboard with power delay circuitry based on the Ken Stones CGS63. The power on circuitry provides a delayed-on for the 4 IDC power sockets and helps reduce switch-on loading on he power supply as well as ensure a cleaner
2008-12-18 by Doug
Hi Dieter, yay! Thanks, Doug --- In Doepfer_a100@yahoogroups.com, wrote: > > > Hi folks using the A-152 with a cv input immediately gives rise to the > > need for a trigger on address selection. I'm thinking a socket for > > this could fit at the bottom of the dig outs section. H
2008-12-18 by gabu_004
Thanks allll!!! I should be able to make out something with those suggestions :D cheerzzzz g. --- In Doepfer_a100@yahoogroups.com, "Laurie Biddulph" wrote: > > Just fit another board in the rack. Just make sure you get its power from > the same point the existing board gets it's
2008-12-18 by Guy Drieghe D.
Thanks, Dieter ! If only to prove my point that I'm an idiot... I have several A-111's [with decent sines!], and of course it never occurred to me to use them as a perfectly valid and simple 3340 testbed. Doh ! cheers, _guy (back in kindergarten now) > > Hi folks, > > > > Amazing
2008-12-18 by yahoo@doepfer.de
> Hi folks, > > Amazing what one can learn about sine waves after a month of being off- > line... ;-) > > Not sure if this is the right place to ask, but I recently re-acquired > my old hi-end modular DIY synth, and want to try to either resurrect > it, or sample it for valuable
2008-12-18 by Guy Drieghe D.
Hi folks, Amazing what one can learn about sine waves after a month of being off- line... ;-) Not sure if this is the right place to ask, but I recently re-acquired my old hi-end modular DIY synth, and want to try to either resurrect it, or sample it for valuable spare parts. The
2008-12-18 by achtung_999
Ah well, whichever version it will be.. they all have some application for me anyway. greetings, Ernst On Thu, Dec 18, 2008 at 10:06 AM, wrote: > > Hi Dieter > > > > > That's an interesting option and would not take more than a few hours > to > > > develop (noting but a slimmed A
2008-12-18 by yahoo@doepfer.de
> Hi folks using the A-152 with a cv input immediately gives rise to the > need for a trigger on address selection. I'm thinking a socket for > this could fit at the bottom of the dig outs section. Has anyone done > this? > > Another thought is a difference or differentiator modu
2008-12-18 by yahoo@doepfer.de
> Hi Dieter > > > That's an interesting option and would not take more than a few hours to > > develop (noting but a slimmed A-143-1). > nope. Its not only an AD envelope like in the 143! It is on one hand an > AD (not gate orientated, but triggered only by a positive edge), and
2008-12-18 by Don Kim
You could use a low pass gate, I think that's sort of what you want. On Wed, Dec 17, 2008 at 9:27 PM, Monroe Eskew wrote: > VCA with built-in slew? To remove the "pop" sound of a gate without > the need of an external envelope or slew limiter. > >