Yahoo Groups archive
Messages
Page 308 of 564 · 28179 messages matched
2007-06-08 by Ross Goniakowski
they have adaptor kits at the local Walgreens or Radio Shack around here... ----- Original Message ---- From: ErnstKarel To: Doepfer_a100@yahoogroups.com Sent: Friday, June 8, 2007 8:58:29 AM Subject: [Doepfer_a100] Re: A-198 Ribbon Controller Questions That's right, type A male
2007-06-08 by ErnstKarel
That's right, type A male on both ends. They're a little hard to find but they're out there. I had to replace mine at one point and it took some looking to find a short one; sorry but I can't remember now where I finally got it from..... --- In Doepfer_a100@yahoogroups.com, "Adam
2007-06-08 by Adam-V
My ribbon controller arrived today and I'm looking forward to playing it however the cable that came with it has the wrong connector at one end. The ribbon and the module both have "USB type A Female" connectors but the cable I was supplied has a "USB type B Male" connector at on
2007-06-07 by mss_panzer
I appreciate everyone's suggestions thus far. Time to find my solder. --- In Doepfer_a100@yahoogroups.com, "Tim Stinchcombe" wrote: > > There is nothing particularly special about the design, it is simply > one of the standard state-variable configurations, albeit using the > inh
2007-06-04 by Tim Stinchcombe
There is nothing particularly special about the design, it is simply one of the standard state-variable configurations, albeit using the inherent integrator action of a (compensated) op amp - it is to be found in at least one of the filter books that I have. The only real 'novelt
2007-06-04 by gabu_004
Oh yes, sorry I sent you an email about the plan b model 10. but I don't remember if I incluede the email where you can reply me back at because I don't use my yahoo acc at all. there it is kakihara.004@gmail.com thanks again gabriel:)
2007-06-04 by Florian Anwander
Hi > I just received two new modules from MFB > http://www.mfberlin.de/Produkte/Module/module.html > They look made very well. I made some pics available here: > http://fa.utfs.org/diy/mfb/ > > I hope I can provide sound examples soon. Though I still have no sound examples, here
2007-06-04 by Matthew Davidson
two frames available 220-240v versions located in the USA US buyers who buy both get a free voltage transformer - plug in and go will ship internationally via UPS $380 USD + shipping paypal accepted
2007-06-04 by davevosh@aol.com
In a message dated 6/4/2007 12:29:03 AM Pacific Daylight Time, hardware@doepfer.de writes: As the poll results are not very convincing I think we will collect pre-orders and manufacture the module only if we collect at least 25 orders. dieter, put me down for 2 ! a useful, long o
2007-06-04 by bellenger_a
Yep, me too... I'll get one (at least) of these along with hopefully coming up A185-2 and A182... Alexandre > > > In a message dated 6/4/2007 12:29:03 AM Pacific Daylight Time, > hardware@... writes: > > As the poll results are not very convincing I think we will collect > pre-or
2007-06-04 by hardware@doepfer.de
> Wouldn't a simple diode provide sufficient protection from negative > voltages? > > /Silas In most cases a diode will be sufficient. In addition I'd recommend a serial resistor to be on the safe side. I forgot to mention another peculiarity for this modification: as the interna
2007-06-04 by David Salter
Nice find Florian and simple enough, I assume it will work just as well with +/- 12V? Cheers David David Salter Senior Consultant PSG Reuters Messaging: david.salter.reuters.com@reuters.net (t) +44 (0)20 7542 2402 | (m) 07990562402 | (f) 52699 Get the latest news at Reuters.com _
2007-06-04 by Florian Anwander
Hi, on analogue heaven maillist I received the hint, that such a module already exists in Ken Stones CGS-System: http://www.cgs.synth.net/modules/cgs60_sba.html Best regards, Florian Florian Anwander wrote: > Hi, > > I suggest a Reamping/ext-in/DI-Module (A-119-2 ?). What for is
2007-06-04 by Silas Johansen
Wouldn't a simple diode provide sufficient protection from negative voltages? /Silas On 6/4/07, hardware@doepfer.de wrote: > > > hi. > > i have the a161 hooked up to the a160, which receives the clock > > output from the a190. > > what i'd like to do (in view of recent posts i wo
2007-06-04 by hardware@doepfer.de
We designed a Polivoks filter about one year ago but we stopped the project as Shawn Cleary of Analogue Haven informed us that such a filter is under development by the Polivoks inventor Vladimir Kuzmin. It should be available soon from Analogue Haven. Best wishes Dieter Doepfer
2007-06-04 by hardware@doepfer.de
As the poll results are not very convincing I think we will collect pre-orders and manufacture the module only if we collect at least 25 orders. Our minimum production quantity is 100 and we have to reduce the risk to manufacture a shopkeeper. Best wishes Dieter Doepfer > -----Ur
2007-06-04 by hardware@doepfer.de
> Are there any future plans for making drumsynth modules? not from our side (Doepfer). There are already a lot of modules from other manufacturers available (e.g. MFB or Analogue Solutions). Best wishes Dieter Doepfer
2007-06-04 by hardware@doepfer.de
> hi. > i have the a161 hooked up to the a160, which receives the clock > output from the a190. > what i'd like to do (in view of recent posts i won't say "need" > :) ) is to have the 161 use > other divisions from the 160 than those which go into it. i don't > want to mess aroun
2007-06-03 by dingfutzer
The following gear auctions end this evening on eBay: Electra EP-550 12 Bit Delay PAiA Tubehead Kenton Pro4 Midi/CV Converter w/custom machined and wired single rackspace patch panel Sequentix P3 Sequencer - Factory built, unused and new in box Doepfer A100: A114 Ring Modulator,
2007-06-02 by ilanode
If DIY is an option: http://m.bareille.free.fr/modular1/vcf_polivoks/vcf_polivoks.htm Rgds, Ingo --- In Doepfer_a100@yahoogroups.com, "mss_panzer" wrote: > > So when might we be able to see a Polivoks VCF? Perhaps based on the A- > 124 design, with a HP/LP mix potentiometer and a
2007-06-02 by mss_panzer
So when might we be able to see a Polivoks VCF? Perhaps based on the A- 124 design, with a HP/LP mix potentiometer and a solo BP pot? Anybody have any thoughts on this?
2007-06-02 by Bryan E Cornell
I have a variety of modular things for sale. Would prefer to ship in the US. Analogue Systems French Connection $1800 + shipping (I would greatly prefer it if buyer could pick up in the DC area, but I realize that's probably a long-shot.) For a description see http://www.analogue
2007-06-01 by Doepfer_a100@yahoogroups.com
The following Doepfer_a100 poll is now closed. Here are the final results: POLL QUESTION: Would you want Doepfer to manufacture the A164 Manual Gate module (second version)? (www.doepfer.de/a164) CHOICES AND RESULTS - Yes!, 9 votes, 47.37% - maybe..., 6 votes, 31.58% - no., 4 vot
2007-06-01 by bruce thedekaa
Hmmm, nice to hear you talk about modular drums... I have been thinking about and looking for modular drumsynths with the sonic range and control of a pearl syncussion, but than with CV inputs. But the only drums i find aren't like that at all (with a small exception for the meta
2007-06-01 by Chris Muir
At 2:01 PM +0000 6/1/07, Stu Grimshaw wrote: >a135-2a: >... i could lose the cv-input for panning ... As someone who does a lot of dynamic panning, I would never give up CV inputs for pan. >a135-2c: >couldn't hurt to double the outputs as 6.3mm jacks (simple parallel would do), s
2007-06-01 by David Salter
Don't get me wrong guys, my module count is over a hundred (modest I know in comparison to some of the members here) and the wish list is growing all the time. :-D David Salter Senior Consultant PSG Reuters Messaging: david.salter.reuters.com@reuters.net (t) +44 (0)20 7542 2402 |
2007-06-01 by Bakis Sirros
:-D --- David Salter wrote: > Nothing like a bit of gear lust Bakis. > > I love the way we all use the expression "need" when > we mean desire :o) > > David > > David Salter > Senior Consultant > PSG > > Reuters Messaging: > david.salter.reuters.com@reuters.net > (t) +44 (0)20 75
2007-06-01 by Florian Anwander
Hi David, I think you mistunderstand. This is a "need" in fact Florian (second secretary of anonymous synth collectors) David Salter wrote: > Nothing like a bit of gear lust Bakis. > > I love the way we all use the expression "need" when we mean desire :o) > > David > > David Sal
2007-06-01 by Silas Johansen
David, From a "moduholic" perspective "need" might be the correct term ;) /Silas - who's turning into a moduholic himself... On 6/1/07, David Salter wrote: > > Nothing like a bit of gear lust Bakis. > > I love the way we all use the expression "need" when we mean desire :o) > > D
2007-06-01 by David Salter
Nothing like a bit of gear lust Bakis. I love the way we all use the expression "need" when we mean desire :o) David David Salter Senior Consultant PSG Reuters Messaging: david.salter.reuters.com@reuters.net (t) +44 (0)20 7542 2402 | (m) 07990562402 | (f) 52699 Get the latest new
2007-06-01 by Bakis Sirros
all these MFB modules seem great. i need both the drum modules, plus the sequencer module plus the triple DCO.... when i can afford them, that is... best regards, Bakis. --- hardware@doepfer.de wrote: > I use Manfreds DRUM-01 and 02 in our demo system. > Very cool and easy to use
2007-06-01 by David Salter
Thanks Dieter. Makes sense to me. I'm particularly interested in the two modules that Florian has purchased. A triple DCO is a nice to have for bass patches (among other things) and the trigger sequencer for programmed resets of envelopes, LFO's, logic inputs, Sequencers as well
2007-06-01 by Stu Grimshaw
hi. i have the a161 hooked up to the a160, which receives the clock output from the a190. what i'd like to do (in view of recent posts i won't say "need" :) ) is to have the 161 use other divisions from the 160 than those which go into it. i don't want to mess around at the 160,
2007-06-01 by hardware@doepfer.de
I use Manfreds DRUM-01 and 02 in our demo system. Very cool and easy to use for drum sounds (much easier that to patch the sounds with several A-100 modules). The DRUM-01/02 are triggered by a Schaltwerk and processed in the A-100 (mainly with BBD modules and filters - and the A-
2007-06-01 by David Salter
Florian, Very cool. I have my eyes on both of these. Really would like some feedback on sound and functionality. Best wishes David David Salter Senior Consultant PSG Reuters Messaging: david.salter.reuters.com@reuters.net (t) +44 (0)20 7542 2402 | (m) 07990562402 | (f) 52699 Get
2007-06-01 by Florian Anwander
Hi, I just received two new modules from MFB http://www.mfberlin.de/Produkte/Module/module.html They look made very well. I made some pics available here: http://fa.utfs.org/diy/mfb/ I hope I can provide sound examples soon. Florian
2007-06-01 by Stu Grimshaw
good day all, dieter, the new modules are super. a135-2a: as someone who drags his stuff out of cars and onto stages, and so doesn't have a monster case, i place a lot of value on space in the rack. personally, i could lose the cv- input for panning and build myself the mute (any
2007-06-01 by Michael Wagner
On 5/30/07, Florian Anwander wrote: > Your module in general works as it can and should do. Topic 2 might be > a question of trimming (I cannot judge from here). Thanks a lot for your informative reply, Florian. These issues didn't bother me very much, but I still wanted to know
2007-06-01 by Stu Grimshaw
just wanted to add my vote for florian's module (don't remember much about impedances). my main problems are all associated with ins and outs, unspectacular problems, but ones that i have in nearly every setup. if the following were available, i'd be wishlessly happy: preamp with
2007-06-01 by Silas Johansen
Hi Florian, Hmm... but if I remember my Ohms law correctly that would mean that the impedance would be determined entirely by the level of the signal and the resistance of the input in the stomp box. Hence, using a VCA to change the signal level would also change the impedance. O
2007-06-01 by Florian Anwander
Hi Silas > Does a VCA output have an impedance? Of course :-). Each signal output has an impedance. It does not matter, whether the signal is generated electromechanical by a microphone or electronical by a synth module. The impedance can be seen as the AC equivalent to a DC resi
2007-06-01 by Silas Johansen
Hi Florian, Does a VCA output have an impedance? I would expect it to have a level and to expect an impedance within a certain range of the input that it connects to, whereas impedance is a term that I mostly see in reference to inputs and (sometimes) passive outputs (e.g. dynami
2007-06-01 by Florian Anwander
Hi Silas > You can use a VCA to attenuate the signal to line level, How do you change the impedance of an A-100 output with an VCA? Are you aware of of the difference between impedance and signal level? Florian
2007-06-01 by Silas Johansen
You can use a VCA to attenuate the signal to line level, and the existing 119 ext. input to beef it back up to modular levels again. But yes, I can also see how this sort of module could be handy, and you could probably even fit two of them on an 8HP panel if you just needed out
2007-06-01 by austrohungaro2006
Hi, I'm new to the list. I have some modules in a Doepfer portable suitcase (Analogue Systems, Doepfers and Cwejmans). 2 oscillators synced, receiving CV from my A190 MIDI to CV module. I use my system live as bass synth. Some weeks ago my system did that strange thing: suddenly
2007-06-01 by David Salter
That's a great idea Florian. I use various stomp boxes with my system and it's a pain getting level's right for a clean signal. I'll take a couple of those for sure. Either that or provide send and returns within a CV mixer with a switch for changing impedance? Rgds david David S
2007-06-01 by Florian Anwander
Hi, I suggest a Reamping/ext-in/DI-Module (A-119-2 ?). What for is it? If you send a line signal from the A-100 to an external guitar stomp box effect the line level of the signal will cause the guitar effect to distort. Also the output signal of the effect will have wrong impeda
2007-06-01 by synth_ollie
if someone has a a-198 ribbon contr. to part with Im interested.... cheers, OLLIE
2007-06-01 by Bakis Sirros
great! --- hardware@doepfer.de wrote: > OK. Production will start a.s.a.p. > > Thank you > Dieter Doepfer > > > -----Ursprungliche Nachricht----- > > Von: Doepfer_a100@yahoogroups.com > [mailto:Doepfer_a100@yahoogroups.com] > > Gesendet: Freitag, 1. Juni 2007 03:29 > > An: Doepfe
2007-06-01 by hardware@doepfer.de
Great. So I'm waiting for the results of the new poll which of the four version is your favourite. Thank you Dieter Doepfer > The following Doepfer_a100 poll is now closed. Here are the > final results: > > > POLL QUESTION: Would you want Doepfer to manufacture the A185-2 > Preci