Yahoo Groups archive
Messages
Page 66 of 564 · 28179 messages matched
2013-08-16 by Kim Johnsson
Hi! Got some spare fuses now, and I'm set for the next adventure, but I have another question: in my G6, there is no cable going to the +5V connector in the middle of the bus board. Does that mean that the 5V adapter doesn't have a source for its 5 volts, or is it supposed to be
2013-08-16 by Jason Hollis
Had this same problem. Added some new-to-me used modules of dubious quality and zap, down goes the rig. T'was the fuses, replaced both and added another PSU (tiptop uZeus with a beefy 6a regulated PSU) and now everything's happy. On Thu, Aug 15, 2013 at 9:28 PM, Kim Johnsson wrot
2013-08-16 by Kim Johnsson
Hi guys! Yeah, I thought it sounded like a fuse problem, but I couldn't find it yesterday when I was panicking. But just now when I checked, the fuse of the G6 is blown. Have to leave for work now, but I trust the G3 problem is the same. That would sure be a relief. Stocking up o
2013-08-15 by Nicholas Keller
If a ribbon was "off by one", -12V would short to ground. That would certainly be a problem. But it seems like if it happened in two rack cases, the problem is at the module end of the ribbon. Check that right away to rule it out. What module is it? Is it new? Have you used it be
2013-08-15 by Richard Horsman
Probably just the fuse. In my experience Doepfer cases seem to somehow get used to working at a particular power level. Change enough modules and "fzzzt". If there wasn't a cabling problem then my bet's on the fuse. [Non-text portions of this message have been removed]
2013-08-15 by Kim Johnsson
Hello! It looks like I've gone and fried my G6. Today I installed some new modules and a 5V adapter (yay!) and suddenly the G6 just didn't light up anymore. I couldn't find any fault in my cabling, but the fact is that the G6 is dead. No leds light up. I have a G3 as well, and I
2013-08-15 by aletropdj
check the fuse and the transformer (output).
2013-08-15 by crummotius
Hello, I just purchased a used Doepfer A-190 Midi/CV module and I'm having some problems with it. Hoping for a DIY solution. Connected it to my TipTop uzeus flying bus board. Super triple checked polarity of the module as well as the five other modules in my case. uzeus is proper
2013-08-15 by aletropdj
It was my first thought, but the fuse its ok, and its not inside the transformer. I have the A-100 DIY Kit #1 and the problem its on the transformer. I can hear the transformer working but its not giving me output power.... I check with the multimeter (AC mode).... thanks --- In
2013-08-15 by NetPierre
It might just be a fuse... Info at http://patchpierre.blogspot.nl/2012/06/locating-a-100-fuse.html Good luck! Pierre Serné / PatchPierre / NetPierre --- In Doepfer_a100@yahoogroups.com, "aletropdj" wrote: > > Hi all. > > After a long time without using my A100, yesterday I found
2013-08-15 by aletropdj
Hi all. After a long time without using my A100, yesterday I found that my transformer its not working. Any idea? thanks in advance
2013-08-12 by shoskins99
Thank you very much for the clarification Dieter. I'll hold at the current configuration and not add any more cases to the base units. All the best, Stu --- In Doepfer_a100@yahoogroups.com, wrote: > > > Hi Everyone, > > > > So I am very very fortunate to have a monster base A-100
2013-08-12 by Zoë Blade
> As I understand it, (and I'm by no means expert on the Doepfer module). > > The Doepfer wavetable is really small, maybe 128 samples(??). > > So by editing you would create a single cycle of your waveform that > fits exactly that number of sample. > > Then the module will play
2013-08-12 by andy butler
anoop.sahal wrote: > Hi Andy! > > I do think you have an answer to my predicament. You seem to have > explained what I am hearing, it does sound like a glitch caused by > mismatching of sample rates and wave form frequency. > > That number of samples error would easily be audible
2013-08-12 by yahoo@doepfer.de
> Hi Everyone, > > So I am very very fortunate to have a monster base A-100 case > (A-100PMB), on top of that is a 12U Monster case (A-100PMS12) and > on top of that is a 9U (A-100PMS9). It's quite stable and I have > some of the rear metal brackets ordered to bolt them together.
2013-08-11 by Florian Anwander
Hello though Zoe explained the center of topic bravely. One hint to a very clearifying video I saw recently: http://www.youtube.com/watch?v=cIQ9IXSUzuM It explains a lot of things very clear, what is needed and what not (especially, why you don'tneed a 100kHz sampler). Florian
2013-08-11 by Zoë Blade
You don't need a sample rate as high as 100kHz. OK, so A4 is 440Hz. You could sample that at 112,640Hz to get 256 samples per oscillator cycle, sure. But you could instead record an A1 (which plays at 55Hz) at 14,080Hz to achieve the exact same result. This is one reason why most
2013-08-11 by andy butler
anoop.sahal wrote: > Well, the sample rate was 24Khz for a 1Khz wave form. > > Still sounded like a buzz. > > I am missing something. If frequency was absolutely spot on 1KHz that would have been exactly 24 samples for one cycle. That should have been ok, provided that the Akai c
2013-08-11 by Zoë Blade
Hi again Anoop! Yes, that's it exactly! Sorry, I hope I wasn't too patronising earlier, I never know how much the person I'm talking to already knows... in this case, quite a lot by the sounds of things! On an interesting and related note, you know how a wheel spinning really fas
2013-08-11 by anoop.sahal
Hi Andy! I do think you have an answer to my predicament. You seem to have explained what I am hearing, it does sound like a glitch caused by mismatching of sample rates and wave form frequency. That number of samples error would easily be audible. I've been dissapointed for 25 y
2013-08-11 by Zoë Blade
Hiya! OK, so when you sample something, you're basically storing a very blocky picture of it. The higher the sample rate, the smoother the picture, the lower the rate, the blockier the picture. As a separate thing entirely, bear in mind that any given waveform can be said to be m
2013-08-11 by anoop.sahal
Zoe! You are a genius, it falls into place, sample rate at least twice the maximum harmonic!!! Not merely twice the fundamental!! No wonder it sounded rubbish. I never got the inference of the reference to the component harmonics, I feel a right plonker! Thanks Zoe. Means that my
2013-08-11 by Zoë Blade
Hi! If you're sampling something 12,000 times a second, and that thing is moving up and down 6,000 times a second, then you're going to get a sample of it being up, then a sample of it being down, and so on. You'll have to sample it playing at a much lower frequency than 6kHz. Ho
2013-08-11 by anoop.sahal
Thanks Zoe, as always your explainations are succint but I am not very bright so I am afraid I do need more detail. The akai sample rate is 24 Khz bandwidth 12 KHz. I have read the sample rate should be at least twice the fequency of the wave form that is to be sampled. Well, the
2013-08-11 by anoop.sahal
I would welcome your help to understand wavetable synths. I thought I had them sorted in my mind but now I am not sure I have a 12 bit Akai S900 , max bandwidth 12Khz. I sampled a 6Khz triangle wave and truncated it to one cycle and looped it, It sounded like a square wave buzz.
2013-08-10 by achtung_999
Checked the photo, impressive rig man! Grtz, Ernst On Sat, Aug 10, 2013 at 12:26 AM, shoskins99 wrote: > ** > > > Added a photo in the album. > > > --- In Doepfer_a100@yahoogroups.com, "shoskins99" wrote: > > > > Peter and James - Thanks guys for the replies, agree the modules ar
2013-08-09 by James Husted
If you are reaching that height you might as well go rack mounted and get some good rack towers to put things in. It makes it a lot harder to steal too. My rig is 4 A-100P6 boxes stacked 2x2 and that is about as tall as I would want to do - go wider and get a rolling chair. -Jame
2013-08-09 by shoskins99
Added a photo in the album. --- In Doepfer_a100@yahoogroups.com, "shoskins99" wrote: > > Peter and James - Thanks guys for the replies, agree the modules aren't too bad on their own but they add up LOL - 12U case packed feels like about 40-45lbs so that plus 2 x 9U would be say a
2013-08-09 by shoskins99
Peter and James - Thanks guys for the replies, agree the modules aren't too bad on their own but they add up LOL - 12U case packed feels like about 40-45lbs so that plus 2 x 9U would be say another 50-60lbs so the base is carrying approx. 100lbs - so I guess that will hold? eekk
2013-08-09 by Peter Sedin
modules don't carry much weight.. would not worry about that! size is the main issue here.. just get a ladder when it gets to high :) 2013/8/9 shoskins99 > ** > > > Hi Everyone, > > So I am very very fortunate to have a monster base A-100 case (A-100PMB), > on top of that is a 12
2013-08-09 by shoskins99
Hi Everyone, So I am very very fortunate to have a monster base A-100 case (A-100PMB), on top of that is a 12U Monster case (A-100PMS12) and on top of that is a 9U (A-100PMS9). It's quite stable and I have some of the rear metal brackets ordered to bolt them together. My question
2013-08-03 by woof_dave
Thanks Dieter - will do. Dave. --- In Doepfer_a100@yahoogroups.com, wrote: > > > I'm getting some odd behaviour out of the arp in my Dark Energy Mk1. > > > > All modes and controller messages to control the arp give the > > expected behaviour, apart from the "Overwrite" mode. Whe
2013-08-03 by Bakis Sirros
for sale in fine condition: Doepfer G6 with psu2 (1200mA's) 230volts european voltage, with schucko plug, for 240 euros total, including shipping and pp fees! for sale in EU only, of course. please contact me off-list. thanks, :) Bakis. [Non-text portions of this message have bee
2013-08-02 by nilsquak
Thanks, Dieter! A jumper would be a great solution. Best Nils --- In Doepfer_a100@yahoogroups.com, wrote: > > > Hi guys just wondering. Does the new version of the A-135 > > feature normalisations for the individual VCAs? For example, will > > a VCA be removed from the mix out, i
2013-08-01 by yahoo@doepfer.de
> Hi guys just wondering. Does the new version of the A-135 > feature normalisations for the individual VCAs? For example, will > a VCA be removed from the mix out, if the dedicated out of the > VCA is used like in the Intellijel HexVCA or the Linnix? > > Thanks > > Nils The firs
2013-08-01 by nilsquak
Hi guys just wondering. Does the new version of the A-135 feature normalisations for the individual VCAs? For example, will a VCA be removed from the mix out, if the dedicated out of the VCA is used like in the Intellijel HexVCA or the Linnix? Thanks Nils music here: nqmusic.band
2013-07-31 by Bakis Sirros
hi all, for sale in fine condition, with ribbon cable and screws: euro version module: Flight Of Harmony Plague Bearer (rev 2.3), price is 63 euros total, including registered shipping and pp fees. paypal payment. please, contact me OFF-list. thanks, :-) Bakis. [Non-text portions
2013-07-31 by cosmosuave
Upon communicating with Chris at Doepfer we were able to fix the issue by updating to firmware version darktime_V1.10_fw_c_120229.zip from the most recent beta I was using... bri. --- In Doepfer_a100@yahoogroups.com, "cosmosuave" wrote: > > Will do thanks... > > --- In Doepfer_a1
2013-07-30 by cosmosuave
Will do thanks... --- In Doepfer_a100@yahoogroups.com, wrote: > > > I have noticed or maybe I am dreaming that when I turn the the > > pulse width pot clock wise the pulse width is short thus > > shortening the gate time on the DE... When it is fully counter > > clockwise the gat
2013-07-30 by yahoo@doepfer.de
> I have noticed or maybe I am dreaming that when I turn the the > pulse width pot clock wise the pulse width is short thus > shortening the gate time on the DE... When it is fully counter > clockwise the gate length is long... I am quite sure it should be > the other way around.
2013-07-29 by christian ienni
hi everyone! added a couple recent tracks in the "new" section of my site http://ienni.net - lots of a100 but also lots of everything else. "spontaneous ambience" is just that - a bit of off-the-cuff ambient randomness. "paralysis of choice" is just a first ragged effort at somet
2013-07-29 by mcetilia
Perfect, thanks so much! Cheers, Mark --- In Doepfer_a100@yahoogroups.com, wrote: > > > Hi all, > > Wondering if anyone here has done this mod? > > > > I'm not sure whether I should be: > > a) leaving the capacitor in place & soldering the legs together, > > b) removing the capac
2013-07-29 by david.salter@thomsonreuters.com
If it pulse width should it not be a square at mid point and narrow either side? -------------------------- Sent using BlackBerry David Salter Thomson Reuters 02075422402 07990562402 From: cosmosuave [mailto:race_slick@yahoo.com] Sent: Monday, July 29, 2013 02:51 PM GMT Standard
2013-07-29 by Nicholas Keller
Yes, As D. Doepfer pointed out, the info is on their website. It's quite simple. I did the same to mine, only the other way around (UK to US). Nick On Jul 29, 2013, at 4:21 AM, wrote: > > Hi Group! > > > > This will be my first contribution after having lurked on the > > list for
2013-07-29 by analogmonster@ymail.com
Not a problem. It took me a long while to realise, I ended up buying 2 DIY psu kits when I was building my original case and not using one of the psus. I guess the extra rails were useful though. Good luck
2013-07-29 by glitzerstrahlmusic
Fantastic! Thank you all so much! This looks like a pretty straight forward operation, but I will make sure to consult with a friend who is a certified electrician. Henrik http://glitzerstrahl.com --- In Doepfer_a100@yahoogroups.com, Nicholas Keller wrote: > > Yes, > > As D. Doep
2013-07-29 by Zoë Blade
I can't believe I didn't actually check first... -.- http://www.thomann.de/gb/doepfer_a_100_bus.htm Wonderful, thank you!
2013-07-29 by achtung_999
Hey there, I wonder if anyone that already owns the new Doepfer unit has a nice video that shows some basic stuff. I keep searching the web with little luck. And most people using the Bananalogue or original Serge have mostly videos out where the workings of the module aren't qui
2013-07-29 by analogmonster@ymail.com
Yes it is, eg Thomann 29 euro On 29 Jul 2013, at 13:45, Zoë Blade wrote: > Hi! > > I managed to buy an old G3 case that's a bit of a fixer-upper... (It looks and smells like it might have been sitting in a shed for a good few years...) > > Our plan (my more-electronics-inclined p
2013-07-29 by cosmosuave
I have noticed or maybe I am dreaming that when I turn the the pulse width pot clock wise the pulse width is short thus shortening the gate time on the DE... When it is fully counter clockwise the gate length is long... I am quite sure it should be the other way around... I even