Yahoo Groups archive
Messages
Page 10 of 564 · 28179 messages matched
2017-12-30 by Jonathan
Hi everyone. After a bit more research I have answered my own question. There are 8 cores in a cat 5 cable, and Dieter has used all of them in the module. That means there is no separate earth connection. I use nylon washers so my A180-9s were not earthed, consequently when I tes
2017-12-30 by Neil Kagan
Does that mean they’ve been wired to US or Euro standard? I’m no expert but we recent had a nightmare installing cctv at work and found the reason was the installers wired some com ports with the US standard so a couple of wires are reversed. Neil Sent from my iPhone > On 30 Dec
2017-12-30 by Jacco Ville
Seems there are cross-cables also.... I’m not very familiar with CAT cables but when this module was introduced I took a small dive into this kind of connections because the provided cable is a bit short. Sent from my IPhone. > Op 30 dec. 2017 om 11:31 heeft Neil Kagan nkagan@mac
2017-12-30 by Neil Kagan
Do they use a cat5e or cat6 cable? The connector will be the same. Neil Sent from my iPhone > On 30 Dec 2017, at 09:53, Jonathan jss9h@aol.com [Doepfer_a100] wrote: > > Hi everyone. Almost Happy (Christian) New Year. I bought myself a pair of the new multicore modules as a Xmas t
2017-12-30 by Jonathan
Hi everyone. Almost Happy (Christian) New Year. I bought myself a pair of the new multicore modules as a Xmas treat (how incredibly useful in a large system Dieter - amazing that no-one has thought of it before). I have a very odd problem - The modules link perfectly with the cab
2017-12-13 by yahoo@doepfer.de
Yes, the modules A-138s, A-150 and A-151 will be available in the black vintage version early in 2018 (probably after NAMM). We manufacture also a limited edition (100 units) of the vintage version of the A-111-5 but we stopped advertising because more than three times the planne
2017-12-12 by Eric Frans
Is there a plan to release A-151 v2 in a black vintage version? I seem to recall reading this somewhere, but maybe I was dreaming. :-) - Eric
2017-12-08 by Florian Anwander
Hi Christian fine -> I'll send you an email Florian Am 07.12.2017 um 18:52 schrieb christian ienni ienni23@yahoo.com [Doepfer_a100]: > hi Florian! > > i have ONE 132-3 old version with the 3360 -- http://www.florian-anwander.de
2017-12-07 by christian ienni
hi Florian! i have ONE 132-3 old version with the 3360 (works perfectly, just the usual rack rash... btw when you say you "don't care FOR rack rash" do you mean you don't care "ABOUT" any cosmetic issues, or that you do not WANT any cosmetic issues with the mod? sorry, just tryin
2017-12-07 by Florian Anwander
Hello, I have two shimmering new A-132-3 dual VCA modules. Both are with the new coolaudio V2164D VCA, which allows amplification of the signal. Unfortunately this possibility is counterproductive in my use case. So I am looking for two A-132-3 modules with CEM3360. I offer a 1:1
2017-12-04 by Neil Kagan
Ah ok thanks Dieter. Neil Sent from my iPhone > On 4 Dec 2017, at 09:04, yahoo@doepfer.de [Doepfer_a100] wrote: > > > Hi to you all, > > > > Do you know if the QVCO adapter for the A-126 was ever sold? And > > f not would Doepfer make one off? I just got the A-126 and would > > l
2017-12-04 by yahoo@doepfer.de
> Hi to you all, > > Do you know if the QVCO adapter for the A-126 was ever sold? And > f not would Doepfer make one off? I just got the A-126 and would > like to use the A-110-4 with it. > > Regards, > > Neil As far as I remember this idea never left the prototype state. But on
2017-12-03 by Florence Michel
Hi, I know that the A-143-9 is intended to be coupled to the 126, but the A-110-4 I do not know
2017-12-02 by Neil Kagan
Hi to you all, Do you know if the QVCO adapter for the A-126 was ever sold? And f not would Doepfer make one off? I just got the A-126 and would like to use the A-110-4 with it. Regards, Neil Sent from my iPad
2017-11-15 by vclab@protonmail.com
thank you Dieter!!
2017-11-15 by Jacco Ville
Hi John, I’ve got a few cases with PSU2 and PSU3. PSU3 is a switched supply and noiseless. You could change them, it’s easy. Best regards, Jacco Ville Sent from my IPhone. > Op 15 nov. 2017 om 11:35 heeft John Hollis john@hollis.co.uk [Doepfer_a100] het volgende geschreven: > > H
2017-11-15 by John Hollis
Hi Jacco, I can see the toroidal. These cases were purchased in 2014 so I guess these must be PSU2s. Is the PSU3 a switched mode PSU then? Is it super quiet? Thanks John > On 15 Nov 2017, at 10:01, Jacco Ville jaccoville@yahoo.com [Doepfer_a100] wrote: > > Hello there, > > Sorry
2017-11-15 by John Hollis
Hi Dieter, Thanks for the super quick response! It’s 50Hz hum. It’s not loud, probably within spec, but the other gear in the studio is quiet so it’s just noticeable. We are in Jersey in the Channel Islands. We’re not in the EU, already. It will have come from Thomann but in 2014
2017-11-15 by Jacco Ville
Hello there, Sorry to interrupt..... John, you’re talking about a toroidal. When you’re talking about the PSU2 you’re right but the PSU3 doesn’t have that. Best regards Jacco Ville Holland Sent from my IPhone.
2017-11-15 by yahoo@doepfer.de
> One of my P9 cases has a noisy PSU3. The other four PSU3s are > silent so it’s not normal. Are replacement PSU3s available? Or > even just the toroidal? (I’m an electronics engineer so easy to > replace it myself.) > > Thanks > John Hollis Hello, both PSU are available as spare
2017-11-15 by John Hollis
One of my P9 cases has a noisy PSU3. The other four PSU3s are silent so it’s not normal. Are replacement PSU3s available? Or even just the toroidal? (I’m an electronics engineer so easy to replace it myself.) Thanks John Hollis
2017-11-15 by yahoo@doepfer.de
> any chance to have them in Vintage editions? maybe, but I don't want to promise anything. Until end of this year these vintage version are planned: A-111-5V (limited edition of 100 modules as we discovered 100 CEM3394) A-150V A-151V ("V" means vintage) Best wishes Dieter Doepfe
2017-11-15 by yahoo@doepfer.de
As the A-135-4C envelope follower was designed about one year after the A-138p the first pcb version of the A-138p does not have an internal connector for the A-135-4C. Only the second version of the A-138p (manufactured from about June 2017) is equipped with the additional conne
2017-11-15 by vclab@protonmail.com
any chance to have them in Vintage editions?
2017-11-15 by vclab@protonmail.com
wooh! i have an A-138p Vintage Edition! can all vintage editions accept A-135-4C ?? or i should research before ordering the later? got confused with this one
2017-11-10 by jacco ville
Hope to get the A173 set quick Sent from my IPad
2017-11-10 by Bakis Sirros
http://www.doepfer.de/home_e.htm Bakis Sirros - Parallel Worlds | [Doepfer_a100] group owner | www. parallel - worlds - music. com | www. facebook. com/ parallelworldsmusic | www. DiN. org. uk Virus-free. www.avg.com
2017-11-07 by Scott Rogers
Ok, great. Still good news. I will do the tests I described earlier and report back. Thanks again! Scott -----Original Message----- From: Doepfer_a100@yahoogroups.com [mailto:Doepfer_a100@yahoogroups.com] Sent: Tuesday, November 7, 2017 11:29 AM To: Doepfer_a100@yahoogroups.com S
2017-11-07 by yahoo@doepfer.de
I also tried a simple patch (all modules in the same case/same supply): permanent high gate / LFO rectangle -> A-140 gate in A-140 out -> A-132-3 CV in A-110-1 sawtooth out -> A-132-3 audio in A-132-3 out -> scope There is no diference in the loudness peak between the permanent g
2017-11-07 by Scott Rogers
Yes, that is possible but I also used the analog meter. And since the problem is obvious in the waveform of the recorded audio, and to my ears, it\u2019s obvious that the problem is definitely occurring. The voltages may not be exactly correct on the meter but that doesn\u2019t c
2017-11-07 by yahoo@doepfer.de
I took a look at your video: you cannot measure the peak voltage of an ADSR with a digital multimeter ! For this e.g. an oscilloscope is required. With the digital multimeter an average value over a period of time is measured (depending upon the measurement cycle of the meter in
2017-11-07 by Scott Rogers
Thanks for doing this. That's good news... in a way. Now the question is, why is this happening? I think I will have to empty one of the cases and build a very simple synthesizer with minimal parts and see what happens. Thanks again! Scott -----Original Message----- From: Doepfer
2017-11-07 by yahoo@doepfer.de
It should read "I could NOT detect any difference ...". Sorry. Dieter > -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com [mailto:Doepfer_a100@yahoogroups.com] > Gesendet: Dienstag, 7. November 2017 16:26 > An: Doepfer_a100@yahoogroups.com > Betreff: AW: [Doep
2017-11-07 by yahoo@doepfer.de
Hello, I took an A-140 and cannot confirm this behaviour. That's what I did: - wait about 10 seconds - permanent high signal to the gate input - measuring the ADSR output (especially the peak voltage) with oscilloscope -> peak is about +8.4V - replacing the permanent gate signal
2017-11-07 by Florian Anwander
Hello Scott, Am 07.11.2017 um 14:53 schrieb 'Scott Rogers' scott@scottfromcanada.com [Doepfer_a100]: > Can you provide examples of instruments that work that way? I know of none. > > In the 39 years I have been playing synthesizers I have not seen a single > example of this befor
2017-11-07 by Scott Rogers
Yes, definitely a gate. I was just using “trigger” because I’m concerned about the peak of the attack part of the envelope, not the sustain portion. Although, you can see in the waveforms shown in the video that the sustain level also changes. But all information could be helpful
2017-11-07 by Scott Rogers
Can you provide examples of instruments that work that way? I know of none. In the 39 years I have been playing synthesizers I have not seen a single example of this before now. I have synthesizers made as early as 1973 (Korg 700, Roland SH-1000, Polymoog, Arp Axxe-1975), Late 70
2017-11-07 by Florian Anwander
Hello First of all: we speak of gates, not of triggers! A trigger marks a timestamp of an event. A gate marks the duration and state between the two events(=triggers): key-press and key-release. Am 07.11.2017 um 13:35 schrieb 'Scott Rogers' scott@scottfromcanada.com [Doepfer_a100
2017-11-07 by Ville Oikarinen
> I have not tried an LFO because it would be difficult to trigger the first time. And I haven’t tried a sequencer lately either. I have an SQ-1 I can try. Maybe if you first make the LFO as slow as possible and then slowly increase the speed until you get a trigger, that trigger
2017-11-07 by Scott Rogers
Interesting question, I’ll check it. But that leads to another question: Does the peak output of an envelope depend on the voltage of the trigger? I would think that as long as the trigger is above a certain threshold the envelope will fire in exactly the same way every time. If
2017-11-07 by Florian Anwander
Am 07.11.2017 um 09:45 schrieb Florian Anwander: using) ill add up Uups, this should read "will add up"... -- http://www.florian-anwander.de
2017-11-07 by Florian Anwander
Hello, I'd say this is normal depending on the setting of the envelope and on the setting of the MIDI-interfaces retrigger parameter. All analogue envelopes without full reset (in fact all the ones that you are using) ill add up a bit if the time settings are not zero. Before the
2017-11-07 by acgenerator@att.net
1) I'd check the behavior with another trigger source that leaves the MIDI module out of it as Ville suggested. It'll help isolate the problem source. 2) one theory is that with a single note, the voltage actually starts at 0v but with many notes voltage hasn't quite dispersed wh
2017-11-07 by Ville Oikarinen
> Is this a known issue? Are there combination of modules that can cause this to happen? Could it be the power supplies? I have moved the modules around and found the behavior is the same regardless of how many modules (or which ones) are in a case. Just a simple idea: are you tr
2017-11-07 by Scott Rogers
Hi Folks Sorry to post this again but my whole modular synth is unusable until I fix this problem so I still need help. The problem: All of my envelope generators do the same thing - When I play a note they peak at a certain voltage, lets say 5 volts. But when I play a second not
2017-10-30 by del@cix.co.uk
Jsmes That’s great. From your description I now see that I should have the jumpers installed differently in order to achieve what I’m after. Most helpful - thank you.
2017-10-29 by james.husted@mac.com
I took another look at one of the modules I didn’t have in the case and I may have a more detailed description of what’s going on. There is a three pin header for each section. They are marked with “(GATE)” and “]”, and “(CV)” and “]”. The side with the word on it is connected to
2017-10-29 by del@cix.co.uk
Thanks so much James - very helpful. I’d read that section of the manual but Figure 1 doesn’t actually show the PCB and the jumper positions; it’s a schematic illustrating the routing of the CV and Gate signals to the bus. And since I couldn’t remember whether I’d changed the jum
2017-10-29 by james.husted@mac.com
From the manual: 6. Appendix Module A-185 has two internal jumpers on its circuit board, which are factory-set to send external CV and gate signals to the system bus (see fig. 1). By re-aligning these jumpers, you can convert the A-185 so that it doesn’t take gate and CV signals
2017-10-29 by Neil Kagan
Check the product webpage? Sent from my iPhone > On 29 Oct 2017, at 19:19, del@cix.co.uk [Doepfer_a100] wrote: > > Hi All > > A quick newbie question, if you don’t mind. I’d be grateful if someone could post the CV and Gate jumper settings for the A-185-1 Bus module. I acquired o