Re: BC Manager midi channel issue
2009-01-01 by k5kip_1999
Did you change the channel first before trying the preset? I have found that if I send a preset, for the bcr to settle I have to switch the preset to something
Messages
Browse messages
Page 74 of 110 · 5497 messages matched
RE: [bc2000] Re: BC Manager midi channel issue
2008-12-31 by smokeystovernyc
Mark, Yes, I am referring to the individual channels assigned to buttons and encoders. In BC Manager, I have, for example, all of the cc s in preset 3 set to
Re: BC Manager moved from Yahoo group's file section
2008-12-31 by Mark van den Berg
... Well spotted, Stewart! In my original reply I assumed that it was due to some locking problem because I had been logged in to the Website Builder for
Re: BC Manager midi channel issue
2008-12-31 by Mark van den Berg
... matter what midi channel I have set, it always ends up being channel 16 after transferring to the BCR. I know that I can change the channel manually with
BC Manager midi channel issue
2008-12-31 by joel stover
BC2000 Community: I have a strange bug that I can t figure out. Any help would be much appreciated. I have a BCR2000 with the latest firmware and drivers
Re: BCR2k + REAPER mackie emulation.
2008-12-30 by hooeygoo
Hi Kip- This works very nicely for me so far. I haven t spent a lot of time with it yet, but so far so good. Thanks much for posting it! -Susan
Re: BCR2k + REAPER mackie emulation.
2008-12-30 by k5kip_1999
Also - there is a beta control surface plugin that expands some of the mackie emulation controls. http://forum.cockos.com/showthread.php?t=25455&highlight=mcu
BCR2k + REAPER mackie emulation.
2008-12-29 by k5kip_1999
This file is located here and at my presets page. It is not a full mackie implementation. There are no vpots only pans. No built in premaped plugin control. No
New file uploaded to bc2000
2008-12-29 by bc2000@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the bc2000 group. File :
Re: Absolute vs. Relative modes? reaper fader jumps.
2008-12-29 by k5kip_1999
I am working on a Reaper specific Mackie preset... Look for it either later today or tomorrow. Also, someone has made a plugin for reaper that may help extend
Re: Absolute vs. Relative modes? reaper fader jumps.
2008-12-29 by hooeygoo
Hi guys- Thank you both for that good info and for the Live preset suggestion. So far that looks promising, Kip. I ll have to digest your post further, Mark,
Re: BC Manager moved from Yahoo group's file section
2008-12-28 by Stewart Tansley
If the message people are seeing is Warning - This copy of Website Builder is licensed for another domain , I think the problem is simply as follows. When you
Re: Absolute vs. Relative modes? reaper fader jumps.
2008-12-28 by k5kip_1999
Always restart reaper when you try a new preset on bcr2k. ... expected, so ... DAW, it ... none of
Re: Absolute vs. Relative modes?
2008-12-28 by k5kip_1999
You can try the Live preset in Reaper for basic controls. Faders, mutes, ch. selects, solos, arms, transports, jog and pans, I think are all that
Cubase 4 And BCF2000
2008-12-28 by raidmarji
Hi All I bought a new BCF2000 and Cubase 4 and wondering what to install, a large number of files, and drivers for BCF2000 and Firmware. I m lost. Any Short
Re: [bc2000] Re: BC Manager moved from Yahoo group's file section
2008-12-27 by steve
sounds like the program website builder is licenced to a user AND a domain? Therell be some php script in there checking the url
Re: BC Manager moved from Yahoo group's file section
2008-12-27 by Mark van den Berg
... Hm, as I ve explained earlier this week I m a novice at maintaining websites, but it might have been because I was logged in to the Website Builder
Re: Absolute vs. Relative modes?
2008-12-27 by Mark van den Berg
... Concerning Relative : I m unsure whether it can do what you want, since this depends on the receiving device s capabilities. In any case there s some
Re: [bc2000] BC Manager moved from Yahoo group's file section
2008-12-27 by Tony Cappellini
Every time i clock on that domain, a message pops up in my Firefox. See attached screenshot .
BC Manager moved from Yahoo group's file section
2008-12-27 by Mark van den Berg
Hi everyone, I ve moved BC Manager and BC MIDI Implementation.pdf from the Yahoo group s file section to http://mntn-utils.110mb.com. The Yahoo group s file
Absolute vs. Relative modes?
2008-12-26 by hooeygoo
Hi- When I power up the BCR all rotary settings are at 0, as expected, so the first time I use one to control, say, a volume fader in my DAW, it jumps to 0,
Re: BC Manager - editing Param value?
2008-12-26 by hooeygoo
... Hi Mark- The drunk baboon layout was what kind of clued me in that it was my resolution, since I figured you would have noticed that (unless you were
Re: [bc2000] Re: Midi learn over usb
2008-12-25 by steve
Genius !I tried midevice and it helped me understand the proper setup... Realised I had a tool that did this aready - xlutop chainer I can map controllers on
Re: BC Manager - editing Param value?
2008-12-25 by Mark van den Berg
... I ve done some further research; all in all I ve found the following 3 more or less separate problems (the first 2 we ve already discussed): 1. the knobs
Re: Broken encoder
2008-12-24 by rpcfender
Hi James perhaps you have already tried this but, before launching into stripping the thing down, can I suggest that you swap the software parameters of an
RE: [bc2000] Broken encoder
2008-12-24 by James Glover
I can t find anything relating to cleaning or replacing BCR2000 encoders. Is it worth me opening the unit up and seeing if i can see whats wrong with the
RE: [bc2000] Broken encoder
2008-12-24 by James Glover
Ok, thanks, that is encouraging. I didn t realise that cleaning it could fix it, I had assumed something more fatal had happened. I haven t been using it very
Re: [bc2000] Broken encoder
2008-12-24 by Bob S.
Encoders, a commonly used component in many synths, can be cleaned and/or replaced. One does not need to replace a whole unit or synth due to one erratic
Broken encoder
2008-12-24 by James Glover
My top left encoder is acting very strangely, and I am assuming it is a hardware fault. Rather than smoothly controlling the parameter it is assigned too, such
Re: [bc2000] Re: Midi learn over usb
2008-12-24 by steve
Without the bcr handy Im not sure but it sounds like Ive been doing it all backwards I understood the manual had instructions along the lines of (i) put the
Re: [bc2000] Re: Midi learn over usb
2008-12-23 by John Bryden
I find this is an annoying flaw in assigning controllers to Ableton Live knobs and sliders. Movements in Ableton and saved positions should output on the
Re: [bc2000] Re: Midi learn over usb
2008-12-23 by Robert Krueger
I m primarly a user of Ableton Live. Any VST capabable plugin parameter can be midi learned. It s as simple as turning on Midi Learn in Ableton, selecting the
Re: Midi learn over usb
2008-12-23 by ivaasura
... If your VSTs do not provide MIDI learn, this could be a solution for you: http://www.midevice.com/News.aspx
Re: Midi learn over usb
2008-12-23 by steve
I suspect not Robert. Can i assume all the vsts i have are incapable of doing so or is some setup required 1st in the host - cubase ? ... -- Sent from Gmail
Re: Midi learn over usb
2008-12-23 by rpcfender
Hi Steve ... I m a little confused here. Normally with VST software you set up the BCR/BCF to output a CC (continious controller) Midi message and
Re: [bc2000] Midi learn over usb
2008-12-22 by Robert Krueger
Is the vsti rotary knob you re talking about sending midi CC out routed to your BCR?
Midi learn over usb
2008-12-22 by steve
Hi. I cannot for the life of me get the bcr to learn a vsti rotary knob. What should the bc .syx setting look like in the preset to acomplish this please?
Re: [bc2000] BCF 2000 review in Linux Journal
2008-12-22 by Raphael Campos
Print a PDF from the page! :-) 2008/12/21 Jeff B
Re: BC Manager - editing Param value?
2008-12-22 by hooeygoo
Hi Mark- I have noticed the problem with the fixed-width columns also -- there s no way to drag them out to see the full text. I can t say I ve seen too many
Re: [bc2000] BCF 2000 review in Linux Journal
2008-12-21 by Tony Cappellini
Sorry about that,my browser must have had my login info memorised.
Re: [bc2000] BCF 2000 review in Linux Journal
2008-12-21 by Jeff B
It s not available to non-subscribers. The pages says: The article you are trying to access requires you to be a registered Linux Journal print or digital
RE: [bc2000] Re: Sound interuptions / disturbances (artefacts) with Ableton Live when using the BCR2000
2008-12-21 by James Glover
Kip and All, The problem with mapping controls is that I would have to plan a set in advance (I think, unless I misunderstand this concept). I want to be able
BCF 2000 review in Linux Journal
2008-12-21 by Tony Cappellini
I was surprised to see a review in the Jan 2009 issue of Linux Journal, since the BCF has been out for so long now. It s not a full review, but more of an
Re: Sound interuptions / disturbances (artefacts) with Ableton Live when using the BCR2000
2008-12-21 by k5kip_1999
James you never have to use the mackie thing. You could map those controls using the controller map function in Live. If you the set you will use is pretty
Re: BC Manager - editing Param value?
2008-12-21 by Mark van den Berg
... This is REALLY weird, Susan! ... You re right: the problem is indeed your 115% DPI setting. I ve tested this setting myself and found the same problem.
RE: [bc2000] Sound interuptions / disturbances (artefacts) with Ableton Live when using the BCR2000
2008-12-21 by James Glover
Sorry, that last question was supposed to have a different title - obviously it relates specifically to the mackie mode preset for the BCR2k To:
RE: [bc2000] Sound interuptions / disturbances (artefacts) with Ableton Live when using the BCR2000
2008-12-21 by James Glover
Is there anyway that a button could be swapped to operate the on/off button of effects? I wonder whether you could possibly make a 3rd preset where, say, the
RE: [bc2000] Sound interuptions / disturbances (artefacts) with Ableton Live when using the BCR2000
2008-12-21 by James Glover
One other question, also relating so sound problems. When I run Ableton Live 6 on another machine with Vista, it has terrible problems playing tracks. Any tune
RE: [bc2000] Sound interuptions / disturbances (artefacts) with Ableton Live when using the BCR2000
2008-12-21 by James Glover
Raphael, Great! Thanks that is exactly what the problem was. Is it also worth increasing the driver error compensation? James. To: bc2000@yahoogroups.comFrom:
Re: [bc2000] Sound interuptions / disturbances (artefacts) with Ableton Live when using the BCR2000
2008-12-21 by Raphael Campos
Hello James! I imagine this is a problem with Ableton rather than the BCF. This is normal when the level of latency is not the most ideal for your audio card.