Yahoo Groups archive
Messages
Page 21 of 564 · 28179 messages matched
2016-10-22 by jaccoville@yahoo.com
Hi there all, After having mail contact with Chris from Doepfer who offerd excellent service to take care of a new processor I couldn't resist also order a new A160-5 at Thomann. Once installed in my system it worked like a charm, no latency issues or whatsoever. Thank you again
2016-10-22 by doubleopards@hotmail.com
Thanks Dieter and Analog Monster . I will try this tomorrow evening (first chance I can!!)
2016-10-21 by Analog Monster
Just in case people don't realise there was a keyboard slip there, I'm sure Dieter meant to type 11.9 not 11.0. For it to have a 1% tolerance the range should be 11.9-12.1 volts.
2016-10-21 by yahoo@doepfer.de
> I've just replaced a Doepfer PSU2 with a Doepfer PSU3 in my > Doepfer case. I installed it successfully using install threads > from Muff's, and by referring to my other case which already has > a PSU3 factory installed. > > All the modules are working with the new PSU3 but whe
2016-10-19 by doubleopards@hotmail.com
I've just replaced a Doepfer PSU2 with a Doepfer PSU3 in my Doepfer case. I installed it successfully using install threads from Muff's, and by referring to my other case which already has a PSU3 factory installed. All the modules are working with the new PSU3 but when I power on
2016-10-18 by jaccoville@yahoo.com
And in the end it is a faulty microprocessor. I contacted Doepfer about this and they confirmed. Change of processor and go! Cheers Jacco
2016-10-18 by achtung_999
Ah yes! Of course, sorry Jacco I did not read your message correctly. Ernst On Mon, Oct 17, 2016 at 11:26 PM, Jacco Ville jaccoville@yahoo.com [Doepfer_a100] Doepfer_a100@yahoogroups.com > wrote: Well for me this note in the manual is about the clock input which has to be stable
2016-10-18 by Jacco Ville
Hello Florian, Thank you for your clear explaination. I like the A160-5 to use but I have to have to attention to place the CV one step ahead which isn't a big deal. Now I know why Thanks again Jacco > Op 18 okt. 2016 om 10:57 heeft Florian Anwander fanwander@mnet-online.de [Doep
2016-10-18 by Florian Anwander
Hello Jacco, just think twice: The voltage which sets the division/multiplication factor, comes slightly after the clock-tick, that should be multiplied. So the multiplying/dividing will happen for the next clock tick. Why comes the Voltage after the clocktick? Because there is a
2016-10-18 by Jacco Ville
Hello Dieter, I made the patch exactly by the book. To be sure I made it once again. What I notice is that once the CV from the A155 sends a voltage the A160-5 does shows this by increasing the leds BUT the actual ratcheting of the notes to my A140 adsr follows AFTER the CV has p
2016-10-18 by yahoo@doepfer.de
> Hello Doepfer users, > > When setting up a patch with my A160-5 clockdivider I noticed > that when I send a CV to the multiplier input for creating > ratcheting there is a latency of one sequencer step. > To be clear: I made the patch classic. > > See example in the manual. > S
2016-10-17 by Jacco Ville
Well for me this note in the manual is about the clock input which has to be stable and infact it is in this setup. Only the CV input is getting a voltage which fluctuates to get the ratcheting effect. Jacco > Op 17 okt. 2016 om 23:06 heeft achtung_999 heinrich.himmelwasser@gmail
2016-10-17 by achtung_999
This is stated in the manual. And if you think about it, it makes sense doesn't it? There are no electronics yet, that have psychic powers ;-) Ernst On Mon, Oct 17, 2016 at 9:02 PM, jaccoville@yahoo.com [Doepfer_a100] Doepfer_a100@yahoogroups.com > wrote: Hello Doepfer users, Whe
2016-10-17 by jaccoville@yahoo.com
Hello Doepfer users, When setting up a patch with my A160-5 clockdivider I noticed that when I send a CV to the multiplier input for creating ratcheting there is a latency of one sequencer step. To be clear: I made the patch classic. See example in the manual. So one A155. The po
2016-10-14 by Martin Alaçam
I think the problem is with the divider, not the osc. It did some other strange things today, although most of the time it works, I can't put my finger why it gets funny once in a while. Maybe it is the lots of multiples going out of the divider+sequencer, I don't know... Also th
2016-10-12 by Martin Alaçam
Hello, That's good news, congrats! Looks like everybody was waiting for the 4 hp osci... And it is a nice one for sure, just this one quirk. It just skips a beat irregularly, would be a nice random if i didn't have 149-2 already. The pulse-width is in the middle, if I bring it to
2016-10-12 by yahoo@doepfer.de
> Hello, > > The pulse wave of PVCO at lfo speed doesn't work well with the > A-160 clock divider on my system. It skips beats and stutters. I > tried to send the pulse through the trigger modifier module but > that did not help. A-160 works with everything else. I have the > pVC
2016-10-12 by Martin Alaçam
Hello, The pulse wave of PVCO at lfo speed doesn't work well with the A-160 clock divider on my system. It skips beats and stutters. I tried to send the pulse through the trigger modifier module but that did not help. A-160 works with everything else. I have the pVCO connected to
2016-10-11 by maltemark@gmail.com
Thanks!
2016-10-10 by Zoë Blade
> I'd replace A-114, A-148 and A-170 by the new A-184-1 !! I'd completely missed this, and it's exactly what I thought Doepfer should do, combine otherwise-redundant modules to save space. I guess I might just be selling my A-114, A-148 and A-170 now, and getting this instead...
2016-10-10 by yahoo@doepfer.de
Hello Michael, it's difficult to recommend a certain module configuration as it depends a lot from the ideas of the user. Here are my comments. I'd replace A-114, A-148 and A-170 by the new A-184-1 The A-120 is nearly the same as the 24dB output of the A-108, i.e. I would omit th
2016-10-10 by Jacco Ville
Hello Michael, Nice list. It's very personal which modules will fit in your setup so I can't advice you in this. One thing I would do is to use a second A154 for your to get the two A155s both the extra controls. Good luck Jacco Ville Verstuurd vanaf mijn iPhone SE Lunatik > Op 9
2016-10-09 by michaelhesse10@yahoo.de
Hello I´am new in this group. Michael from Germany 50 years old. I want buy an A-100 System ( 4 rows each 168 TE / HP ) Below a list of modules. I would be appreciate if you can give me some suggestions (opinion , help ) to complete the system. ( Have 78 TE / HP free space ) some
2016-10-03 by Florian Anwander
Hello Jacco, of course a Jomox bassdrum does not need this (I own a Xbase09 ;-) ...). My thought was more generally about how to handle bassdrum sounds. Florian On 02.10.16 23:07 , Jacco Ville jaccoville@yahoo.com [Doepfer_a100] wrote: Hi Florian, That's a complete different appr
2016-10-02 by Jacco Ville
Hi Florian, That's a complete different approach than I had in mind although it's a brainshaker ;-) What I had in mind was a filter not only to shape the sound but also to muffle it without to alter the mix level. The "thin" sound you refer to is not a common thing with a Jomox m
2016-10-02 by Florian Anwander
Hello Jacco Just one hint: the best bassdrum-exciter is a resonating high(!)pass-filter. If you have an existing (thin) bassdrum sound, then send it through a highpass filter. Set the resonance to nearly selfoscillation, and then tune the cutoff frequency down. Example: if your o
2016-10-02 by jaccoville@yahoo.com
Hello groupmembers, I would like to "build" a dedicated case for bassdrum, kick ..... Etc My wishlist at the moment is a Jomox modbase09 with a Doepfer Lowpass filter which I want to place in a Doepfer MC100 "small case". Which Doepfer filter would be the best choice in this setu
2016-09-27 by Jacco Ville
.... Got it! Cheers Verstuurd vanaf mijn iPhone SE Lunatik > Op 27 sep. 2016 om 13:13 heeft jaccoville@yahoo.com [Doepfer_a100] het volgende geschreven: > > Hello there everyone, > > > > Just bought an used Dark Energy 1 but when cleaning and checking the jumpers I forgot to pay
2016-09-27 by yahoo@doepfer.de
I'll send you the drawing directly to your email address. I have to point out that the PSU has to be installed and wired by a qualified person only who is familiar with the electrical safety rules ! Otherwise there is danger to life. Best wishes Dieter Doepfer > -----Ursprünglich
2016-09-27 by thebadproducer@yahoo.co.uk
Hello Group! Does anyone have - or know where I can find - a mounting template for the PSU3? I'd like to mount one into a case and I need to drill holes for the stand-offs. Hope there is one! Cheers Charlie
2016-09-27 by jaccoville@yahoo.com
Hello there everyone, Just bought an used Dark Energy 1 but when cleaning and checking the jumpers I forgot to pay attention to the ribbon cable positions. Could anybody please show the right connections? Have a nice day Jacco Ville
2016-09-26 by ventrality@gmail.com
vielen dank Dieter!
2016-09-26 by Florian Anwander
Am 26.09.2016 um 10:31 schrieb yahoo@doepfer.de [Doepfer_a100]: > The pcb has not changed. Just the serial resistor at the audio input(R15) > has been reduced from 22k to 10k to increase the input sensitivity. R15 is > located behind the audio input level control below C1/10u. >
2016-09-26 by yahoo@doepfer.de
From the distance it's impossible to find out what's wrong. But the A-111 cannot be damaged by a "wrong" CV coming from the bus access module. It will withstand any CV in the range -12V...+12V and the bus access module cannot generate a voltage beyond these values. If you cannot
2016-09-26 by yahoo@doepfer.de
The pcb has not changed. Just the serial resistor at the audio input(R15) has been reduced from 22k to 10k to increase the input sensitivity. R15 is located behind the audio input level control below C1/10u. Version 2 of the A-120 with the transistor arrays has been equipped from
2016-09-26 by yahoo@doepfer.de
Please look at the FAQ page mentioned in my last email. Here you find some links to suppliers (Reichelt, Mouser, Newark). Best wishes Dieter Doepfer > -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com [mailto:Doepfer_a100@yahoogroups.com] > Gesendet: Sonntag,
2016-09-26 by ventrality@gmail.com
hi friends Yesterday my dear A111 stopped to work..., perhaps (i m not totally sure) it was damaged by a wrong voltaje supplied by my doepfer bus-Access module, which had a intermitent failure due to a defective bus ribbon cable..( i know i don t need to use the cv input because
2016-09-25 by christian ienni
haa!!! Cheetah ms6 and Kawai SX240... getting flashbacks to reading Keyboard magazine in the '80s! ;-) but seriously (and relevant) - that is exactly what happened with my Regelwerk! it started going weird, figured it was the battery, opened it up, and lo and behold one of the ba
2016-09-25 by Analog Monster
I say almost identical. I've just noticed it's got 3 pins not 2. Reichelt actually has the 3 pin in stock. If you have anything else a bit old it might be worth checking. Actually these batteries are notoriously an old synth destroyer. Cheetah ms6 (an oberheim matrix 6 clone) and
2016-09-25 by Analog Monster
Did you try going to the FAQ link suggested earlier? It has an image of the type of battery needed, along with a few working links like reichelt. I have also found something that is almost identical on eBay by looking for 3.6 ni-cd > > 3 x NI-CD Button Rechargeable Back Up Batter
2016-09-25 by christian ienni
and apologies again! (it's late here ^_^ ) - just saw your other message - yes it's whatever the current version of the Z3A65 is. i was able to find a replacement here in the us, but as i said that was some years back. maybe Dieter knows where to find some? From: "christian ienni
2016-09-25 by christian ienni
that's not it. i am sorry i can't remember or find the exact part number, but it's shorter, with a 3-pin mount. go ahead and open up your Regelwerk and take a look, there should be a part number on the battery you can match. wish i could be more help! :-) From: "endif.org@gmail.c
2016-09-25 by endif.org@gmail.com
I just read the second reply, with the 3.6v detail. Would this one suffice? TLH-5902/P Tadiran Batteries | Battery Products | DigiKey TLH-5902/P Tadiran Batteries | Battery Products | DigiKey Order Tadiran Batteries TLH-5902/P (439-1031-ND) at DigiKey. Check stock and pricing, vi
2016-09-25 by endif.org@gmail.com
Thanks so much for the quick reply! I'm having trouble sourcing a replacement Z3A65 battery I've removed from the main board of my Regelwerk. What are the specs I should be looking for in a replacement?
2016-09-23 by Martin Fay
Am I right in thinking that at some point the A-120 was revised to allow a higher drive level? If so is there a revision/date on the PCB which could be used to identify this? Martin Sent from my iPhone
2016-09-22 by christian ienni
some years back i had the same exact thing start happening with my (also blue) Regelwerk, and Dieter is right: it was the battery! opened the unit, desoldered the old one, installed a brand new one (standard 3.6v type) and it's been going gangbusters since! From: "yahoo@doepfer.d
2016-09-22 by yahoo@doepfer.de
Hello, the ser.no. tells me that the unit has been manufactured in 1999. If the battery has never been changed I'm quite sure that it is defective and has to be replaced. Details on the FAQ page of our website: www.doepfer.com > English > FAQ > General > Lifespan of rechargeable
2016-09-22 by endif.org@gmail.com
I have a Regelwerk that does not boot fully. - PSU = 9v DC, correct polarity (- out, + in, same iconography) 1a (500ma required) - Nothing plugged in but the PSU, so no chance of loops or external influence. - Boots as far as displaying the OS Screen: "Regelwerk V.171 Doepfer (c)
2016-09-19 by yahoo@doepfer.de
> Thanks Dieter...I'll need to check what the ERM Midiclock is > sending when it is running, since this seems to light up the > reset LED and is perhaps interfering with the reset message that > the box sends to the A190-4. Midi has no realitime "RESET" message available, only st
2016-09-19 by sj230962@gmail.com
Hi Florian, yeah..my error in trying to fix the issue with non-logical thinking :-) I've got a few Roland MC-202s and have had older gear that needs DIN sync (hence my Kenton Midi-DIN Sync converter box that lives happily in my rig). I do know the difference ;-) I just hoped the