Yahoo Groups archive
Messages
Page 22 of 564 · 28179 messages matched
2016-09-19 by sj230962@gmail.com
Thanks Dieter...I'll need to check what the ERM Midiclock is sending when it is running, since this seems to light up the reset LED and is perhaps interfering with the reset message that the box sends to the A190-4. However, when the clock isn't running and I try to send a reset
2016-09-19 by yahoo@doepfer.de
> Hi - I'm using the A190-4 as my midi interface, with master > clock provided by an ERM Midiclock unit. > > > When I hit start, the clock starts but the Reset light activates > on the A190-4. When I reset from the ERM nothing happens. When I > stop the ERM the clock stops (obvio
2016-09-19 by yahoo@doepfer.de
> Hello list, > My A106 SEM filter has malfunctioned, possibly due to a bad power > cable. One of the chips is damaged and needs replacement: it has > 14 pins. Is this chip easily replaced? > Thanks! Royce Hello, you may try to repair the module by replacing the integrated circui
2016-09-19 by yahoo@doepfer.de
> So today i was lucky enough to write in on an order for both > A-111-2, A-111-3 modules and the A-184-2 [ yeeeej :)] Following > question comes to mind regarding the latest discussion abouth new > vco module thru-zero capablities and the mentioning of the JH3 > dual cem 3340 vc
2016-09-19 by Florian Anwander
DIN-Sync and MIDI are two completely "different pairs of shoes". DIN-Sync is a quasi analogue parallel format, MIDI-Clock is a digital serial format. The only thing they have in common is that they use a round five pin connector. But even flying saucers and stone age wheels have
2016-09-19 by sj230962@gmail.com
Doh - I may have solved my problem. I'm sending MIDI and not DIN Sync 24.....excerpt from Schneidersladen website ..... Special feature in DIN Sync24 mode: press the encoder while powreing up and choose between a DIN Sync signal with 24ppq or an alternative Eurorack-compatible an
2016-09-19 by sj230962@gmail.com
Hi - I'm using the A190-4 as my midi interface, with master clock provided by an ERM Midiclock unit. When I hit start, the clock starts but the Reset light activates on the A190-4. When I reset from the ERM nothing happens. When I stop the ERM the clock stops (obviously) and the
2016-09-18 by Anthony
I use bitsbox.co.uk cheap and reliable. Sent from Mail for Windows 10
2016-09-17 by kevinfglover@yahoo.com
I don't have one of these or can seem to find a schematic. However, a magnified view of a image of the A106 SEM seems to show the 14 pin chip being a TL084CN. A very common,inexpensive, Quad Op-Amp. With the ICs being socketed, (danke Dieter) there should be no problem replacing
2016-09-17 by rrooyyccee@yahoo.com
Hello list, My A106 SEM filter has malfunctioned, possibly due to a bad power cable. One of the chips is damaged and needs replacement: it has 14 pins. Is this chip easily replaced? Thanks! Royce
2016-09-16 by ninonine@xs4all.nl
So today i was lucky enough to write in on an order for both A-111-2, A-111-3 modules and the A-184-2 [ yeeeej :)] Following question comes to mind regarding the latest discussion abouth new vco module thru-zero capablities and the mentioning of the JH3 dual cem 3340 vco module.
2016-09-14 by Neil Kagan
Ah I see thanks Dieter; it took a few reads but I think I understand! Regards, Neil Sent from my iPhone > On 12 Sep 2016, at 13:42, yahoo@doepfer.de [Doepfer_a100] wrote: > > The drop to zero is not the important thing (except for LFO applications > where the modulation can stop
2016-09-12 by yahoo@doepfer.de
I took two A-101-2 from our stock and cannot reproduce any distortion. Looking at the circuit distortion is implausible because only vactrols and operational amplifiers are working. I'd like to know if anybody else in this group a similar distortion problem with the A-101-2. The
2016-09-12 by yahoo@doepfer.de
The drop to zero is not the important thing (except for LFO applications where the modulation can stop and continue again when the linear control is turned up again). But the linear frequency bias/offset is important because the linear FM is different when the bias/offset gets lo
2016-09-08 by Neil Kagan
Thanks Dieter, Can I ask what the application of a manual drop to zero is? Neil Sent from my iPhone > On 8 Sep 2016, at 18:56, yahoo@doepfer.de [Doepfer_a100] wrote: > > The A-111-2 has no thru-zero feature but only a manual control and a CV > input for linear frequency adjustmen
2016-09-08 by yahoo@doepfer.de
The A-111-2 has no thru-zero feature but only a manual control and a CV input for linear frequency adjustment/modulation. With all controls at minimum the oscillation nearly stops (typ. 1Hz in VCO mode). But we are working on a thru zero version of the A-111-2 (probably named A-1
2016-09-08 by Neil Kagan
Hi people, Does anyone know if the new VCO has thru zero capability? It looks like it from the LF control being able to go to 0 but there isn't specify mention. Neil Sent from my iPhone
2016-09-08 by yahoo@doepfer.de
I'll have a look at the module when I'm back from the Modular Days in Linz/Austria next week. Best wishes Dieter Doepfer > -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com [mailto:Doepfer_a100@yahoogroups.com] > Gesendet: Mittwoch, 7. September 2016 22:59 > A
2016-09-07 by vytis.puronas@yahoo.com
Hi All, I have an 18U system consisting 100% of Doepfer modules. My system is housed across two P9 suitcases. I am a huge fan of the system, but I am at a point of trying to improve the sound as much as possible. I own 3 x A-101-2 low pass gates. This issue is present in all thre
2016-09-05 by yahoo@doepfer.de
Hello Florian, thank you for your help. On our website the procedure is described on the FAQ page (> A-100 > My A-100 system does no longer work). I'll add your more detailed description concerning the subsequent installation of the modules. Take care ! Dieter > -----Ursprünglich
2016-09-05 by Florian Anwander
You have to check this step by step, module by module: 1.) switch off the system, remove all modules, switch on again, and check whether on all busboards the +12 and -12 LEDs are lit. 2.) switch off the system, mount one module and connect it to the busboard, switch on again, and
2016-09-04 by frzrscott@gmail.com
Hi, Hope someone can help here. I've just bought an LC9 case and am experiencing trouble setting it up. All my modules are mounted correctly with the red stripes matching the -12v... however, most of my modules are unresponsive when switched on, i'm only getting a few lit LEDS on
2016-08-26 by Ian Campbell
hi all, i'm one half of synthcurious, and we put on synth meetings and electronic music events in coventry, uk. we have a meeting coming up on saturday the 17th september, where there will be plenty of doepfer on show. we also have a very interesting gig lined up to finish the da
2016-08-23 by karelvanbezooijen@yahoo.com
You're welcome. Sometimes I wish that misspelling my name is the worst thing that could happen to me! ;-) Karel.
2016-08-22 by Nicholas Keller
KarEl, Sorry for misspelling your name, I was tired, it autocorrected, and I didn't notice. Thank you for linking to the other thread but I have yet to even check the transpose input. I will keep this added resistor mod in mind when I do. Nick On Sunday, August 21, 2016, Nicholas
2016-08-22 by Nicholas Keller
Thanks Karl, I'll check this out tomorrow On Sunday, August 21, 2016, karelvanbezooijen@yahoo.com [Doepfer_a100] Doepfer_a100@yahoogroups.com > wrote: Here is my thread about this module from about a year and a half ago: https://groups.yahoo.com/neo/groups/Doepfer_a100/conversati
2016-08-22 by karelvanbezooijen@yahoo.com
Here is my thread about this module from about a year and a half ago: https://groups.yahoo.com/neo/groups/Doepfer_a100/conversations/messages/26234 maybe it's useful but I must admit I didn't get it right as it should be. And I still haven't bought a second one ;-). Best regards,
2016-08-21 by Nicholas Keller
I believed I was making progress, but noticed something while probing to troubleshoot the faulty upper unit. When I connect the A-176 to the A-156, there is a voltage drop. Disconnected, the A-176 output measures 05.00V, but when I connect to the CV1 or CV2 Input of either of the
2016-08-21 by Nicholas Keller
Jacco, Thanks for your response. Only after writing that message did I actively search for the calibration document on the Doepfer page. I followed its instructions of using the Quint setting on the A-156 and the sweepable output from the A-176, removing the A-150 from the signal
2016-08-21 by Jacco Ville
The A-155's Row 1 Pre Out was monitored using the DCV setting on hand-held DMM. Step 1 was held to output the maximum value, fully CW. With range set to 1V, I adjusted P9 until 1.000V on DMM. However, switching to 2V and 4V, the scale was still not wide enough. I chose to tune 4V
2016-08-21 by Nicholas Keller
Dieter and Jacco, I inspected my three A-156 modules and A-155 this morning. The A-155's Row 1 Pre Out was monitored using the DCV setting on hand-held DMM. Step 1 was held to output the maximum value, fully CW. With range set to 1V, I adjusted P9 until 1.000V on DMM. However, sw
2016-08-19 by Jacco Ville
..... Please take note that my approach of regulating is not the only way and so is my explaination ;-) Hope you got the idea Verstuurd vanaf mijn iPhone SE Lunatik > Op 19 aug. 2016 om 18:22 heeft Jacco Ville jaccoville@yahoo.com [Doepfer_a100] het volgende geschreven: > > I not
2016-08-19 by Jacco Ville
I noticed some different behaviour of my A156's when testing my setup. With a tuner on an A110 tuning from the A155 from C to C (seq knob fully ccw and cw) some came to C or B and when switching between 1V 2V and 4V it was not consistent. So.... Time to make voltages visible. Yes
2016-08-19 by Nicholas Keller
I hadn't thought to check the 156 for adjustment. I've been struggling with tuning for some time now and almost always have a 156 in the patch. Thanks for bringing this to my attention. I'll check the scale of my 155 while I'm at it! On Thursday, August 18, 2016, Jacco Ville jacc
2016-08-18 by Jacco Ville
....And I certainly will do that. Learning learning.... Funny thing, I am more collecting and adjusting my Doepfer setup (or Dieter room as my wife is calling it) then making sounds. But I think it is the best way to know the working of every part of this system. Cheers Jacco Vil
2016-08-18 by yahoo@doepfer.de
> .... By the way ;-) > > I found out the attenuator function of P1 and P2 > Very handy to set the threshold of the quantizer behaviour. > I noticed that with critical voltages from my A155's with a knob > fully cw the voltage of 0.970V in 1V modus was not enough to get > a full
2016-08-18 by Jacco Ville
.... By the way ;-) I found out the attenuator function of P1 and P2 Very handy to set the threshold of the quantizer behaviour. I noticed that with critical voltages from my A155's with a knob fully cw the voltage of 0.970V in 1V modus was not enough to get a full scale from C t
2016-08-18 by Jacco Ville
Hello Dieter, Thank you for your reply. Everything is clear. I managed to get two of my A156's within nice specs (read: same behaviour) I have two others to check but now I know how to adjust them really fine. Thank you again. Jacco Verstuurd vanaf mijn iPhone SE Lunatik Op 18 au
2016-08-18 by yahoo@doepfer.de
> Hello Dieter, > > > I have an issue with the A156. > > Besides the small notes on your website about tuning the A156 is > there a more specific thing to measure? > Between the steps of 0.0833333 V there is a small window of quantizing. > When the voltage goes up and down there
2016-08-18 by yahoo@doepfer.de
> Dear all @Doepfer, > > is a Vintage Version for this definitely versatile LPG in the pipeline? > > THX for a short reply. > > Best from Cologne > Wolfram So far there are no plans. But I agree that it would make sense. I'll have to look at our production plans when the next bat
2016-08-17 by jaccoville@yahoo.com
Hello Dieter, I have an issue with the A156. Besides the small notes on your website about tuning the A156 is there a more specific thing to measure? Between the steps of 0.0833333 V there is a small window of quantizing. When the voltage goes up and down there it switches differ
2016-08-09 by Jacco Ville
Hello Dieter, I got the message, time for work ;-) Best regards Jacco Ville Verstuurd vanaf mijn iPhone SE Lunatik Op 9 aug. 2016 om 18:24 heeft yahoo@doepfer.de [Doepfer_a100] het volgende geschreven: >> Hello Jacco >> >>> Am 09.08.2016 um 15:17 schrieb jaccoville@yahoo.com [Doe
2016-08-09 by Jacco Ville
Hi Florian, I don't need 1000mA but more like 400mA or so. Maybe this value can be reached with just another adapter and without modification. Any advice will be welkome. Thank you for your kind reply. Jacco Verstuurd vanaf mijn iPhone SE Lunatik > Op 9 aug. 2016 om 15:39 heeft F
2016-08-09 by yahoo@doepfer.de
> Hello Jacco > > Am 09.08.2016 um 15:17 schrieb jaccoville@yahoo.com [Doepfer_a100]: > > I recently bought the A-100MC case incl adapter. > > With a maximum of 200mA ,which is a bit lean, I think I can't > use it for a few modules to my wish. > > Like the A190-4, A190-8 and....?
2016-08-09 by Florian Anwander
Hello Jacco Am 09.08.2016 um 15:17 schrieb jaccoville@yahoo.com [Doepfer_a100]: > I recently bought the A-100MC case incl adapter. > With a maximum of 200mA ,which is a bit lean, I think I can't use it for a few modules to my wish. > Like the A190-4, A190-8 and....? > Is it possi
2016-08-09 by jaccoville@yahoo.com
Hello there, I recently bought the A-100MC case incl adapter. With a maximum of 200mA ,which is a bit lean, I think I can't use it for a few modules to my wish. Like the A190-4, A190-8 and....? Is it possible to use an other adapter with more power and if so, what is the maximum
2016-08-01 by kevinfglover@yahoo.com
Ignore my previous message. I figured out the problem (loose nut behind the wheel) It turns out that in my excitement of my new toys, I... uh... kinda didn't finish soldering the connectors on the bus strip. DOH! Product works fine. I'm blaming the pain meds.
2016-08-01 by kevinfglover@yahoo.com
Just got a new Doepfer a-143-9. Plugged it in to the rack and had no function from it at all. Power cable is correct. Other modules are working fine. Any suggestions on troubleshooting aside from sending it back?
2016-07-30 by Jacco Ville
Solved! Just a small breath at P6 and....perfect. Nice weekend....where ever you are Jacco Ville Verstuurd vanaf mijn iPhone SE Lunatik > Op 28 jul. 2016 om 16:18 heeft jaccoville@yahoo.com [Doepfer_a100] het volgende geschreven: > > Hi there everyone, > > While assembling and te
2016-07-28 by jaccoville@yahoo.com
Hi there everyone, While assembling and testing my (all Doepfer!) drone station I noticed that one of the vco's tuning pots on front didn't match center postion when tuned to C and rangeknob at zero. All my other A110's do match quite well but this one sits around 7 on the front