Yahoo Groups archive
Messages
Page 23 of 564 · 28179 messages matched
2016-07-28 by Jacco Ville
Goodmorning Dieter, Thank you, it's something I can work with. Best regards, Jacco Ville Verstuurd vanaf mijn iPhone SE Lunatik > Op 28 jul. 2016 om 09:16 heeft yahoo@doepfer.de [Doepfer_a100] het volgende geschreven: > > The instructions for the adjustment of the frequency offse
2016-07-28 by yahoo@doepfer.de
The instructions for the adjustment of the frequency offset is: about 32Hz in VCO mode with all manual frequency controls at the front panel in center position (no external CVs via sockets or bus). Best wishes Dieter Doepfer > -----Ursprungliche Nachricht----- > Von: Doepfer_a100
2016-07-27 by Jacco Ville
-----all A-143-4 should have a similar frequency range. Maybe the frequency offsets were not adjusted as prescribed----- Hello Dieter, What is that prescription? I mean, are these offset pots some kind of course regulation? Do I have to use a frequencycounter? Best regards Jacco
2016-07-27 by Jacco Ville
Hello Dieter, I double checked the jumpers and though I didn't measure I felt the piggybag heater was warm. I contacted my supplier in Holland and he suggested to send it in. Honestly....thank you very much for your reply but I don't want to "experiment" with a brand new module b
2016-07-27 by Jacco Ville
Hello Florian, My other two A143-4's are also without the CVBus jumper , don't use the bussystem at all, and they work fine. Comparison went 1:1. Jacco Verstuurd vanaf mijn iPhone SE Lunatik > Op 27 jul. 2016 om 09:27 heeft Florian Anwander fanwander@mnet-online.de [Doepfer_a100]
2016-07-27 by yahoo@doepfer.de
Hello Jacco, all A-143-4 should have a similar frequency range. Maybe the frequency offsets were not adjusted as prescribed. There are four trimming potentiometers on the A-143-4 pc board which are labelled "OFFSET 1" ... "OFFSET 4". These are used to define the frequency offsets
2016-07-27 by Florian Anwander
On 26.07.16 23:11 , jaccoville@yahoo.com [Doepfer_a100] wrote: > except for the busCV jumper which I took out. If there is an exception, then this is not a comparison. Have them both setup really the same, then you may find significant results.
2016-07-26 by jaccoville@yahoo.com
Hello Dieter, While building my new drone station I discovered something odd. With all new bought modules there is one which doesn't work properly, an A143-4. Now I already own two of them so I compared them with the same (factory) settings, al jumpers in place except for the bus
2016-07-22 by David Kellett
Good news!! A PMS12 or two is always good. I'm very happy with mine. David www.movingisliving.co.uk Sent from my iPhone > On 22 Jul 2016, at 13:31, vclab@protonmail.com [Doepfer_a100] wrote: > > i had something in mind from a contact via official site about new "joiners" that are
2016-07-22 by yahoo@doepfer.de
> -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com [mailto:Doepfer_a100@yahoogroups.com] > Gesendet: Freitag, 22. Juli 2016 14:31 > An: Doepfer_a100@yahoogroups.com > Betreff: Re: AW: [Doepfer_a100] Re: Help about A-100 Monster Case > Verbinders From our our
2016-07-22 by vclab@protonmail.com
i had something in mind from a contact via official site about new "joiners" that are more strong and proper? i may be wrong, just going around my mind and cant find this email, not 100% sure. anyway will order those 2 codes!! (and an extra pms12 ) thanks to everybody!!
2016-07-21 by yahoo@doepfer.de
> thanks very much David, thats great!! > i needed to short this out because im moving often and cant stand > removing modules each time to screw/unscrew the cases!! thats fantastic! > > what about the stability of the "roof" case?? > it is a bit scary when looking at some pictur
2016-07-21 by karelvanbezooijen@yahoo.com
Hi Florian, Thank you so much for clearing this out! Now I know what to do to achieve what I want. The good old method of mixing audio tracks afterwards :-). I don't have schematics either. Random Source doesn't supply them with the kits. The only one that is available is from Ke
2016-07-20 by David Kellett
I have a monster base with two PMS12s on top. The top one angled. It seems very steady and stable. The base and first case are full the top one is a bit empty still. I think it is sensible to fill from the bottom stability wise. Are attachments allowed here? Here is a photo if th
2016-07-20 by vclab@protonmail.com
thanks very much David, thats great!! i needed to short this out because im moving often and cant stand removing modules each time to screw/unscrew the cases!! thats fantastic! what about the stability of the "roof" case?? it is a bit scary when looking at some pictures ... is it
2016-07-20 by David Kellett
All the screwing together is external. If you put a case on top of a monster base you can do it with both cases with there kids on - to avoid miss hap with dropping on onto the modules of another. To put an angled one on top - I think it would be much easier if the top on is empt
2016-07-20 by vclab@protonmail.com
Hi Dieter and friends! im in contact with thomann about but need to make sure about 2 things for these parts: A-100 Monster Case Verbinder gerade A-100PMVG (straight) A-100 Monster Case Verbinder gewinkelt A-100PMVW (angled) - are these parts the latest revised versions (2016)? -
2016-07-20 by Florian Anwander
Hi Karel, compare: A111-A138(FullOpen)-SSG-Cubase with A111-MAVCA(FullOpen)-SSG-Cubase You see, that in both cases the high frequency level drops. So now it is clear: The cause is NOT the A-138, because the same behaviour can be seen with a non-Doepfer-module too. The problem is
2016-07-20 by karelvanbezooijen@yahoo.com
I did some various patches and took screen captures of them. I don't seem to manage to attache the files so I put them in my dropbox: Doepfer Doepfer Shared with Dropbox View on www.dropbox.com Preview by Yahoo Hopefully the naming convention I used is clear. Otherwise please ask
2016-07-19 by Florian Anwander
Am 19.07.2016 um 07:30 schrieb karelvanbezooijen@yahoo.com [Doepfer_a100]: > Again no difference in freq or on the scope Ok, then try to put some other module (which should be in a kind of bypassmode) between the A-138 and the SSG. Like: A-111 -> A-138 -> otherModule -> SSG -> Cu
2016-07-19 by karelvanbezooijen@yahoo.com
OK, thank you for your patience. I did set it up like you wanted now. Again no difference in freq or on the scope Regards, Karel.
2016-07-18 by Florian Anwander
Hello Karel Am 18.07.2016 um 08:39 schrieb karelvanbezooijen@yahoo.com [Doepfer_a100]: What do I do next? Just put the output of the SSG to the multiple? No, the next step is to connect the INPUT of the SSG to the multiple. I want to test, whether the input of the SSG pulls the o
2016-07-18 by karelvanbezooijen@yahoo.com
Hello Florian, I'm not sure if I understand correctly. I set up the patch as you suggested: A-111 -> A-138 -> multiple -> Cubase What do I do next? Just put the output of the SSG to the multiple? I mean with or without any signal going into the SSG? I tried both but I can't see a
2016-07-18 by karelvanbezooijen@yahoo.com
I tried an A-138b, A138a, A138m and A135-1. They all give the same result. I don't own the A-138u.
2016-07-17 by Florian Anwander
Hello Karel, I assume the serge module is not buffered very well, so its input creates an lowpass together with the output of the A-138. I suggest the following test. A-111 -> A-138 -> multiple connect cubase with the multiple. Check the waveform and the frequency range. Then con
2016-07-17 by ninonine@xs4all.nl
Did you try out the A-138u Dual Micro Mixer (2x3) or just an exclusive multiple (cable) for connecting more waveform audio signals to the SSG?
2016-07-17 by karelvanbezooijen@yahoo.com
As you can see in the video that's what I did. When I feed the saw wave directly to the SSG I get that nice high frequency moving sound. When I run the saw wave first through the mixer that's gone. The purpose is to mix several wave forms before they go to the SSG. But then as yo
2016-07-16 by Jacco Ville
....and for just to be (in)sure(d)... I replaced the psu2 for a psu3 There is really nothing to it, 15 minutes work. Only the 5V wire is a piece I'll have to get at work. But don't need it with the todays setup. With 2000mA of power under the hood I feel a lot better. Almost fini
2016-07-16 by Jacco Ville
Hello Karel, I would say, try without the a138b and hear the result. Best regards Jacco Ville The Netherlands Verstuurd vanaf mijn iPhone SE Lunatik > Op 16 jul. 2016 om 06:13 heeft karelvanbezooijen@yahoo.com [Doepfer_a100] het volgende geschreven: > > I have this "issue". I don
2016-07-16 by karelvanbezooijen@yahoo.com
I have this "issue". I don't know if it is Doepfer related but I thought this may be the place to start my investigation. I put a short movie on my YouTube channel. https://youtu.be/b3JF4wtP8lE Best regards, Karel.
2016-07-15 by jaccoville@yahoo.com
Hello there, Besides my big system I am building a small setup targeted for dronelike sounds. With a Doepfer A-100LC9 Low Cost case 9HE incl. A-100PSU2 still unused I filled it with Doepfer modules (ofcourse). With a calculation for powersurge I came to 960mA. Now I know that the
2016-07-11 by Jacco Ville
Update ....and yes, a new A155 is on its way to Holland :-) Good service from Doepfer and Thomann Best regards Jacco Ville Verstuurd vanaf mijn iPhone SE Lunatik > Op 8 jul. 2016 om 14:44 heeft Jacco Ville jaccoville@yahoo.com [Doepfer_a100] het volgende geschreven: > > Update >
2016-07-08 by Jacco Ville
Update Seems the A155 is sent to Doepfer. Best regards Jacco Ville Verstuurd vanaf mijn iPhone SE Lunatik Op 4 jul. 2016 om 09:39 heeft yahoo@doepfer.de [Doepfer_a100] het volgende geschreven: >> Update >> >> >> Today I received another new A155 (ordered separately, not the one u
2016-07-07 by Neil Kagan
That's great news!! It's the one effect I don't have access to in the Doepfer system. Sent from my iPhone > On 7 Jul 2016, at 16:27, yahoo@doepfer.de [Doepfer_a100] wrote: > > > Still no frequency shifter then? :( > > The redesign of the frequency shifter has been started also (e
2016-07-07 by yahoo@doepfer.de
> Still no frequency shifter then? :( The redesign of the frequency shifter has been started also (external quadrature VCO, e.g. A-101-4 or A-143-, including a squelch circuit). But we have to make one step after the other and are able to release only about one module every 2-3 m
2016-07-07 by Neil Kagan
Still no frequency shifter then? :( Sent from my iPhone On 7 Jul 2016, at 14:33, yahoo@doepfer.de [Doepfer_a100] wrote: >> This oscillator seems to have piqued a lot of interest. Are there any news on this, and on the possibility of an >> expander? Looks like a really powerful mo
2016-07-07 by yahoo@doepfer.de
> This oscillator seems to have piqued a lot of interest. Are there any news on this, and on the possibility of an > expander? Looks like a really powerful module to me. > > Allt gott / Best wishes, > Mikael Altemark The final version of the A-110-6 is still under development. We
2016-07-07 by Mikael Kopimi Altemark
This oscillator seems to have piqued a lot of interest. Are there any news on this, and on the possibility of an expander? Looks like a really powerful module to me. -- Allt gott / Best wishes, Mikael Altemark
2016-07-04 by yahoo@doepfer.de
> Just wondering if anybody has run into complications using shorter standoffs with the A-143-4. With my current Monorocket > case the depth of the A-143-4 unfortunately allows me only two locations before I bump into the power supply. I notice > the original standoffs offer gene
2016-07-04 by yahoo@doepfer.de
> Update > > > Today I received another new A155 (ordered separately, not the one under guarantee) and coupled it with the A154 which > made me happy to see all worked fine. > > > The "bad" A155 has arrived at Thomann service center. > > Have a nice weekend > > > Jacco Ville I'm
2016-07-01 by Jacco Ville
Update Today I received another new A155 (ordered separately, not the one under guarantee) and coupled it with the A154 which made me happy to see all worked fine. The "bad" A155 has arrived at Thomann service center. Have a nice weekend Jacco Ville Verstuurd vanaf mijn iPhone SE
2016-06-29 by Jacco Ville
Hello Dieter, I already sent the A155 back to Thomann with a small note attached. No conformation received yet. The A154 seems fine, I hope. It didn't flash (and popped) like the A155. I have to check it. I'm glad things will be solved. Thank you for your reply. Best regards Jacc
2016-06-29 by yahoo@doepfer.de
That's an obviously wrong wired module ! The red stripe of the ribbon cable connecting the trigger and potentiometer boards to the control board should be the other way round. It has no effect until the A-155 module is running alone (without A-154). But if A-155 and A-154 are con
2016-06-24 by Jacco Ville
Hello Florian, After this small disaster I checked my other two a155/154 sets so that's where I discovered the wrong wiring. After that I ignored the red lines and tried again but the a155 only made a few steps before it frooze. So I am sure something has been blown up. I ordered
2016-06-24 by Florian Anwander
The pictures come through fine. Does it still flash when you put it back to the original state? Can you post pictures with the 155 and 154 connected? Basically the colour does is not the important part. You should obey the orientation of the flat-cables. I will post later a pictu
2016-06-24 by Jacco Ville
Btw I have pictures of the original wiring of this specific A155 Don't know if I can upload them here. Jacco Ville Verstuurd vanaf mijn iPhone SE > Op 24 jun. 2016 om 10:02 heeft Jacco Ville jaccoville@yahoo.com [Doepfer_a100] het volgende geschreven: > > Hello Florian, > > Thans
2016-06-24 by Jacco Ville
Hello Florian, Thans you for your reply. I think it's broken. All leds flashed. It worked until the a154 came in. I connected everything with red lines like the a155 was connected, this resulted in damage. Best regards Jacco Ville Verstuurd vanaf mijn iPhone 5 Black OPS Edition >
2016-06-24 by Florian Anwander
Hello Jacco I assume that this will be a warranty "repair". In fact they only have to rewire it correctly and send the module back to you. Dieter will assumingly clear this after his vacation. Florian Am 24.06.2016 um 08:32 schrieb jaccoville@yahoo.com [Doepfer_a100]: > Hello Die
2016-06-24 by jaccoville@yahoo.com
Hello Dieter, Last year I bought an A155. It worked very well. A few days ago I also ordered an A154. After making the connections fun was over sadly. I did some investigation (I already have two sets of 155/154 which work fine) and comparison I discovered that the wiring on the
2016-06-20 by judasursus@yahoo.com
Just wondering if anybody has run into complications using shorter standoffs with the A-143-4. With my current Monorocket case the depth of the A-143-4 unfortunately allows me only two locations before I bump into the power supply. I notice the original standoffs offer generous s