Yahoo Groups archive
Messages
Page 321 of 564 · 28179 messages matched
2007-01-20 by Bakis Sirros
hello, you can syncronize the software synths of Native intruments and the maq 16/3 via their midi interface. meaning: the midi input of the maq 16/3 and the midi output of the midi interface of the computer that you are running the soft synths on. you just select one as the mast
2007-01-20 by credo99muro
Dear Bakis, This is credo99muro from Japan. Thank you for your reply. By the way, what does your following sentence of "synced via midi, right ?" mean ? "they should run in sync perfectly together synced via midi, right ?" ciao !! --- In Doepfer_a100@yahoogroups.com, Bakis Sirros
2007-01-20 by stimbox
Dieter, Many thanks! Problem solved. Found the fuse and changed it. All the best, Tim > > The fuse is located at the mains inlet on the rear panel of the A-100 frame > (exception: suitcase version with mains inlet at the front). One has to > disconnect the mains cable and remove
2007-01-19 by cray5656
does anyone here know where in Australia I can buy the 15mm diameter mixer style control knob Rean ? Rapid Electronics UK dont seem to ship outside UK :-(
2007-01-19 by Florian Anwander
Hi Alexandre > Also, I DONT KNOW WHAT A BIT CRUNCHER does? > > Can someone explain briefly, thank you, have a good day... A bit cruncher is not a established descritpion as "oscillator" or "filter" would be. Usually in the audio context it means a function, that converts digital
2007-01-19 by whyterabbyt
--- In Doepfer_a100@yahoogroups.com, "bellenger_a" wrote: > > Here > > http://www.fdiskc.com/syn/ > > > Also, I DONT KNOW WHAT A BIT CRUNCHER does? > > Can someone explain briefly, thank you, have a good day... > > > Alexandre > Bit crushing is primarily a form of digital distort
2007-01-19 by hardware@doepfer.de
> I just purchased an A-113 Subharmonic Generator used from Analogue Haven. I didn't run > methodical tests on it yet. One of the first things I've noticed is works fine for only about 3 > midrange octaves of square input. Above or below it doesn't deliver suboctaves. It also > s
2007-01-19 by hardware@doepfer.de
> Hello, > I have a G6 case with an older PS and think I blew a fuse. > Where is the fuse located? I can't seem to find it. > Thanks, > Tim www.doepfer.com > FAQ > A-100 > Which fuse is used in the A-100 frame (rear panel): The fuse is located at the mains inlet on the rear panel
2007-01-19 by nicholas_kent
I just purchased an A-113 Subharmonic Generator used from Analogue Haven. I didn't run methodical tests on it yet. One of the first things I've noticed is works fine for only about 3 midrange octaves of square input. Above or below it doesn't deliver suboctaves. It also seems to
2007-01-19 by bellenger_a
Here http://www.fdiskc.com/syn/ Also, I DONT KNOW WHAT A BIT CRUNCHER does? Can someone explain briefly, thank you, have a good day... Alexandre
2007-01-19 by Bakis Sirros
hello, they should run in sync perfectly together synced via midi, right? best regards, Bakis. --- credo99muro wrote: > Hello, my friends of DOEPFER's group > This is credo99muro from Japan. > Is it also possible for "MAQ16/3" to sequence the > software synthesizers of "KORE + >
2007-01-19 by selfoscillate
--- In Doepfer_a100@yahoogroups.com, "jeswa" wrote: > > When i first laid eyes on the A-100 system, I immediately wondered > where the stereo outs were. I wish there were a mixer with stereo > outs and led's, like the Plan B model 18. I am currently using an A- > 138b mixer > A-1
2007-01-19 by amnesia
currently I use my Serge mixer, but PLan B has an interesting stereo mixer http://www.fdiskc.com/syn/
2007-01-19 by credo99muro
Hello, my friends of DOEPFER's group This is credo99muro from Japan. Is it also possible for "MAQ16/3" to sequence the software synthesizers of "KORE + KOMPLETE 4" by Native Instruments synchronically? You know "MAQ16/3" is the MIDI/ Analog Sequencer by DOEPFER. Meanwhile "KORE"
2007-01-18 by jeswa
When i first laid eyes on the A-100 system, I immediately wondered where the stereo outs were. I wish there were a mixer with stereo outs and led's, like the Plan B model 18. I am currently using an A- 138b mixer > A-134 panner > external mixer for stereo monitoring. What, if any
2007-01-18 by stimbox
Hello, I have a G6 case with an older PS and think I blew a fuse. Where is the fuse located? I can't seem to find it. Thanks, Tim
2007-01-17 by synthtrader
hi, > Dieter, is it possible to buy a single, bare PCB from an A151 > Sequential Switch for inclusion in a home made Sequencer? > Yours Aye Stuadh I have an extra bare PCB for the A-151. I also have several extra A-150 boards and some other PCBs leftover from the giveaway last ye
2007-01-17 by Mickey Finn
I have this module and I need to make some room for some new cwejman stuff.. Excellent shape- Plugs into the euro rack made by doepfer. http://cgi.ebay.com/ws/eBayISAPI.dll? ViewItem&item=230076759688&ssPageName=ADME:B:EF:US:11 Coleman-
2007-01-17 by hardware@doepfer.de
> Does anybody know if I can use the Midi Out on my guitar effects board > to interface with the A-190? > > I am assuming there would be no problems, but I just want to be sure. > > Thank you in advance. To use the A-190 you need a Midi transmitter that generates Midi note on/off
2007-01-17 by hardware@doepfer.de
> hello to all, > my 2 cents worth - last year, i had to replace one of my doepfer power > supplies - i found that the hardest part was getting the back plates reattached to > those weird sliding nuts. the actually swapping of the old supply for the > new version was quick and pa
2007-01-17 by hardware@doepfer.de
> would it be possible (and not too complicated) to turn this into a +/- 15 v psu ? The main problem is that you will need another transformer (~ 2x18V instead of 2x15V) as there is not sufficient "headroom" for a perfect 15V supply (i.e. without ripple noise). And two resistors
2007-01-17 by hardware@doepfer.de
> So doesn't matters if I split my VCO modules between lower and upper > floor of a G6 case? > > Thank you, > Luca It does not matter if the VCOs are in the same or in different rows. It is essential if the same CV is used for all VCOs. If you want to use an A-185 and the VCOs ar
2007-01-16 by mss_panzer
Does anybody know if I can use the Midi Out on my guitar effects board to interface with the A-190? I am assuming there would be no problems, but I just want to be sure. Thank you in advance.
2007-01-16 by synth_ollie
well, I guess you´re right, nevet thought of that... thanks ! OLLIE --- In Doepfer_a100@yahoogroups.com, neil jendon wrote: > I don't know if the mains transformer > on the doepfer power supply provides enough AC volts > to produce 15 vdc after rectification and regulation.
2007-01-16 by neil jendon
Ah, understood. I don't know if the mains transformer on the doepfer power supply provides enough AC volts to produce 15 vdc after rectification and regulation. I'm sure if you dig around on the WWW, you'll find an electronics supplier in Sweden who sells a dual rail linear power
2007-01-16 by davevosh@aol.com
In a message dated 1/16/2007 12:56:46 PM Pacific Standard Time, synth.ollie@gmail.com writes: It's a bargain and a safer option than > retrofitting a Doepfer supply (IMO). hello to all, my 2 cents worth - last year, i had to replace one of my doepfer power supplies - i found that
2007-01-16 by synth_ollie
yep, but blacet are in the states and Im in sweden (add 25% vat), and I may be able to get the doepfer cheapo, anyone else....? --- In Doepfer_a100@yahoogroups.com, neil jendon wrote: > > Blacet offers a 15v twin rail power supply that costs > about the same as it would to build
2007-01-16 by neil jendon
Blacet offers a 15v twin rail power supply that costs about the same as it would to build your own from scratch. It's a bargain and a safer option than retrofitting a Doepfer supply (IMO). --- synth_ollie wrote: > would it be possible (and not too complicated) to > turn this into
2007-01-16 by Jay
axiombass wrote: > So doesn't matters if I split my VCO modules between lower and upper > floor of a G6 case? You have to get the internal bus jumper cable if you don't already have one to get the CV on more than one row.
2007-01-16 by synth_ollie
would it be possible (and not too complicated) to turn this into a +/- 15 v psu ? cheers OLLIE
2007-01-16 by axiombass
So doesn't matters if I split my VCO modules between lower and upper floor of a G6 case? Thank you, Luca --- In Doepfer_a100@yahoogroups.com, wrote: > If you run more than 2 VCOs with one common CV the A-185 is recommended. > > Best wishes > Dieter Doepfer >
2007-01-16 by hardware@doepfer.de
> I have to replace my existing 3U case with a 6U. Since I'll add > another oscillator (now I have two A-110) should I buy an A-185 module > in order to prevent signal losses? If you run more than 2 VCOs with one common CV the A-185 is recommended. Best wishes Dieter Doepfer
2007-01-16 by Silas Johansen
Signal loss or not - with three VCOs it's going to save you a lot of patching. And it would free up a multiple for other purposes... On 1/15/07, axiombass wrote: > > Hi all, > I have to replace my existing 3U case with a 6U. Since I'll add > another oscillator (now I have two A-1
2007-01-15 by axiombass
Hi all, I have to replace my existing 3U case with a 6U. Since I'll add another oscillator (now I have two A-110) should I buy an A-185 module in order to prevent signal losses? thank you, Luca
2007-01-15 by jalmari3
Analogue Systems makes RS170 dual 5-way multiple. From the manual: "If you simply wish to sum the signals, you can use the RS170 as a pair of passive 4-channel mixers with unity gain." I was under the impression, that it is similar to A-180... Best regards Jari Jokinen > In princ
2007-01-15 by Tim Stinchcombe
> I think these might be the ones: > > http://www.mouser.com/search/refine.aspx?Ntt=550-57001 Rapid in the UK also carry them: That's quite a link, so their home page is: http://www.rapidonline.com/ and parts nos are: 32-0390 32-0395 etc. up to 32-0415 - black knobs with six diff
2007-01-15 by travesty14850
I think these might be the ones: http://www.mouser.com/search/refine.aspx?Ntt=550-57001 At any rate there's a page of Re-An knobs on the Mouser site...give them a look to make sure! > > > I want to get black knobs for my doepfer so they sit better with my > > plan b, livewire, cg
2007-01-15 by doepfer
> I want to get black knobs for my doepfer so they sit better with my > plan b, livewire, cgs panther modular....any idea what I am looking > for and where is a good place to buy them? > > TIA We have these knobs available as spare parts as we use them in our d3 system (same shap
2007-01-15 by doepfer
> I' ve got a question about transposing sequences with my Doepfer Mini > Basis system. The sequencer A-155 with one multiple A-180 is also in > the system. > > I'd like to add the pitch CV from the sequencer A-155 to the pitch CV > from the keyboard (via MIDI-to-CV-module A-190)
2007-01-15 by doepfer
> I was playing around with the Oddity softsynth the other day and got > thinking--I've got more than enough oscillators on my modular (4) to > make some amazing duophonic sounds. > > How would I go about this? I've got the basic Doepfer MIDI-CV > converter and an M-Audio Axiom c
2007-01-15 by doepfer
> Dieter, > > is it possible to buy a single, bare PCB from an A151 Sequential > Switch for inclusion in a home made Sequencer? > > Yours Aye > > Stuadh We have no bare pcbs available as our manufacturer does the complete production: pcbs + electronic parts (ecxept special parts)
2007-01-15 by doepfer
Denis, you find my comments written inline. Best wishes Dieter Doepfer > having another look at the quadrature LFO and the cool looking > companion quad VCA i stumbled upon one feature that i miss in the > current design of the quadrature LFO: a reset/sync input for the > quadrat
2007-01-15 by Florian Anwander
Hi dr_boehm_lebt > Question: what is the reason of the behaviour of the A-180 multiple > module? For adding two control voltages for tonal control you need a precision adder. An adder adds the two voltages, but prevents that the electronics of one module interact with the electro
2007-01-15 by cray5656
I want to get black knobs for my doepfer so they sit better with my plan b, livewire, cgs panther modular....any idea what I am looking for and where is a good place to buy them? TIA
2007-01-14 by Axel Jungkunst
Hi Robert, fine, it seems to work! all the best Axel Doepfer_a100@yahoogroups.com schrieb: > > > Hello, > > This email message is a notification to let you know that > a file has been uploaded to the Files area of the Doepfer_a100 > group. > > File : /mp3 testing the A-155 > Uplo
2007-01-14 by Doepfer_a100@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the Doepfer_a100 group. File : /mp3 testing the A-155 Uploaded by : dr_boehm_lebt Description : Testing the A-155 sequencer with real time transposing via MIDI-keyboard
2007-01-14 by Axel Jungkunst
Hi Robert, ok, next try: which oscillators are i use? Here you can use two CV Pitch Inputs simultaniously to get some strange tunings. Would be the next easy way. best regards Axel dr_boehm_lebt schrieb: > > Hello Axel! > > Thanx for answering! Yes, the quantizer could be used, b
2007-01-14 by dr_boehm_lebt
Hello Axel! That's it!!! Thanx for your tip! It's right, the oscillators (A-110) have two pitch-CV inputs, so I can use CV-in-1 for the sequencer's pitch and CV-in-2 for the keyboard's generell pitch. The multiple A-180 can multiple all CVs to both oscillators... great! Thank you
2007-01-14 by dr_boehm_lebt
Hello Axel! Thanx for answering! Yes, the quantizer could be used, but I don't want to use it, because I want to do some fine tunings with the sequence step pitches outside the tempered tuning... Best regards Robert! --- In Doepfer_a100@yahoogroups.com, Axel Jungkunst wrote: > >
2007-01-14 by Axel Jungkunst
Hi Robert, the easiest way to do this is the use of an A-156 Quantizer module, which has the transpose function too. Imo it is very useful to the A-155, like the A-154 too! All the best Axel dr_boehm_lebt schrieb: > > Hello, > > I' ve got a question about transposing sequences wi