Yahoo Groups archive
Messages
Page 33 of 109 · 5429 messages matched
2010-01-12 by WT
Thanks Tim, I´ll have a go at it tonight. Need to make a special cable then..... WT ----- Original Message ----- From: "Tim Curtis" To: Sent: Tuesday, January 12, 2010 4:25 AM Subject: Re: [Fairlight-CMI] Re: Syncing a IIx As I recall, the sync input in the General Interface box
2010-01-12 by Tim Curtis
As I recall, the sync input in the General Interface box was never implemented. (It's been a while since I've checked it out, but I believe that this is the case. I'll be inside the CMI soon, so I can verify this) You sync the IIx by using a 384 PPQ sync into the sync input on th
2010-01-12 by blixton
If I sampled the fairlight with a good soundcard and a software like autosampler will the sample bank sound the same? Or will it just not be the same? Thanks
2010-01-12 by WT
Hi Josin, thanks for the suggestion but it is not a problem to generate clocks...... I have 10 different sync-boxes that can supply the clocksignals. The problem is how to input them into the CMI and getting it to sync. WT ----- Original Message ----- From: "Josin Miranda" To: Se
2010-01-11 by Josin Miranda
Motu - Volta. Might be a solution, generates clock to PPQ. Josin On 11 Jan 2010, at 23:09, WT wrote: Hi Billy ! Thanks for the answer. The IIx unfortunately doesn´t sync to Midi. The manuals that I have for the General Interface card doesn´t go into detail about how to sync the I
2010-01-11 by WT
Hi Billy ! Thanks for the answer. The IIx unfortunately doesn´t sync to Midi. The manuals that I have for the General Interface card doesn´t go into detail about how to sync the IIx. What I like to do is feed clocks ( 384 ppq as I can decipher from various sources ) into the CMI
2010-01-11 by Bill
In the past - we would record a track of sync tone and then feed it back to the Fairlight (IIx) to sync the Fairlight to tape. I never ttried synching with midi though i would assume this can be done on the IIx. I sync with SMPTE now on a series III. good luck. billyrock --- In F
2010-01-10 by David
I've forgotten! I think I would just send it a sync tone. It should be in the manual. I think it's the 3 pin din connector that I used. SMPTE it will trigger the start time and then the CMI runs at it's own tempo. Not so easy to get it to sync 100% IIRC David --- In Fairlight-CMI
2010-01-09 by WT
Bump ! No one ? WT ----- Original Message ----- From: "WT" To: Sent: Sunday, January 03, 2010 2:03 AM Subject: [Fairlight-CMI] Syncing a IIx > So....I´ve made my masterpiece of music using Page R and want to sync it > to > an external clock source. > > Where do I connect my syncs
2010-01-06 by Rob J
Hi Tom, I'm interested, I will try to dig up some disc images I made a few years back when I was working on CMIExplorer (a Windows GUI to read/write OS-9 disks) and let you know what I have. -Rob From: tomulcahy Sent: Tuesday, January 05, 2010 9:35 AM To: Fairlight-CMI@yahoogroup
2010-01-05 by tomulcahy
I've got KMI's cmios9 working on an old PC, so it's easy to make disc images for series 3. Does anyone want to trade sounds this way?
2010-01-03 by WT
So....I´ve made my masterpiece of music using Page R and want to sync it to an external clock source. Where do I connect my syncsource ? To the CMI XLR Sync connector or, to the 3-pin DIN connector on the General Interface box ? And/or should I make a special cable that goes from
2010-01-02 by David
--- In Fairlight-CMI@yahoogroups.com, "lancelink84" wrote: > > Just wanted to say Happy New Year to all the Fairlight fans around the world! May this be a blessed year for us all! > Thanks! Might get my Series III going again this year..
2010-01-01 by lancelink84
Just wanted to say Happy New Year to all the Fairlight fans around the world! May this be a blessed year for us all!
2009-12-16 by dvdborn
Peter, Thanks for that bit of information. Cheers, David http://dvdborn.blogspot.com --- In Fairlight-CMI@yahoogroups.com, "horiprod" wrote: > > JB is correct, I'm using the AV input of an LCD TV. Pins 4 and 5 from the IIX graphic output are Earth and live for this signal. > > PW
2009-12-15 by horiprod
JB is correct, I'm using the AV input of an LCD TV. Pins 4 and 5 from the IIX graphic output are Earth and live for this signal. PW.
2009-12-15 by Jean-Bernard EMOND
I think Peter use TV LCD, not computer LCD monitor ;) dvdborn a écrit : > > > Hi Peter, > > Would you be so kind to elaborate on how someone can use a TFT with a IIx? > > What are the requirements for the monitor? > What kind of converter cable needs to be made? > > David Vandenb
2009-12-15 by dvdborn
Hi Peter, Would you be so kind to elaborate on how someone can use a TFT with a IIx? What are the requirements for the monitor? What kind of converter cable needs to be made? David Vandenborn http://dvdborn.blogspot.com --- In Fairlight-CMI@yahoogroups.com, "horiprod" wrote: > >
2009-12-15 by horiprod
Maybe not for anyone here, but please tell your old eccentric uncle about the IIX listed at: http://cgi.ebay.com.au/ws/eBayISAPI.dll?ViewItem&item=230412662088&ssPageName=STRK:MESELX:IT Have a peaceful holiday season.... Peter Wielk Horizontal Productions in sunny Sydney
2009-12-06 by blixton
Anyone ever actually use the Cv gate with the page A card on the IIx? Hows it work? Is it reliable? Tight, good timing? Buggy? Thanks
2009-12-04 by JB
Hi Glenn, I am willing to copy my library for you and I think i can organize the system and utility disk for you. I'm from Austria and shipping could be expensive. Send me your mail address and we can talk about the details. Regards, Josef --- In Fairlight-CMI@yahoogroups.com, Dr
2009-12-02 by Dr. Josef Brückl
Hi Glenn, Surely I will help you. Today I have little time. I'll write you tomorrow. Sincerely, Josef -----Ursprüngliche Nachricht----- Von: Fairlight-CMI@yahoogroups.com [mailto:Fairlight-CMI@yahoogroups.com] Im Auftrag von Glenn Gesendet: Dienstag, 1. Dezember 2009 18:20 An: Fa
2009-12-01 by Glenn
Hey Josef, all. My IIx sounds library got damaged, almost entirely all of it , or this would be(I wish) me writing to say I'd help you totally help you( I now have no library, but do have some newly acquired boxes of blank disks). Would be willing to help me copy same, plus the 3
2009-12-01 by JB
Hi, since about a year I'm a owner of a CMI IIx. I've the sound library revision 1.0 and looking for the revision 1.3. Is there anyone who has the library and would be happy to let me copy the disks? Many thanks! Regards, Josef
2009-11-27 by dkevefnzs
Hi again, add on to my previous note: Apparently, your image is more complex. I just note you also have dark lines and a few stray pixels in the middle of the menu options list, so my previous explanation may not be sufficient. Sorry. Greetings, Joerg --- In Fairlight-CMI@yahoogr
2009-11-27 by dkevefnzs
Hi. I think that this comes from one defective bit in a buffer or shift register or even an interrupted printed-wire-connection on the PCB, rather than from a video RAM chip. Because it happens in every vertical line, and in every horizontal place (I guess every 8 pixels?). So mu
2009-11-23 by dvdborn
Thanks all for the monitor tips. I hope I'll manage to get the video card back in 100% working condition. PS: if you like Ryuichi Sakamoto you should also check out Hector Zazou David http://dvdborn.blogspot.com --- In Fairlight-CMI@yahoogroups.com, Glenn wrote: > > After a hopef
2009-11-23 by dvdborn
Thanks all for the monitor tips. I hope I'll manage to get the video card back in 100% working condition. PS: if you like Ryuichi Sakamoto you should also check out Hector Zazou David http://dvdborn.blogspot.com --- In Fairlight-CMI@yahoogroups.com, Glenn wrote: > > After a hopef
2009-11-23 by WT
Thanks Gordon, I will look into it a.s.a.p WT ----- Original Message ----- From: "Gordon JC Pearce" To: Sent: Monday, November 23, 2009 10:41 AM Subject: Re: [Fairlight-CMI] Another CMI IIx monitor question > WT wrote: > >> It doesn´t do this every time. Well, I think you cans ee
2009-11-23 by Gordon JC Pearce
WT wrote: > It doesn´t do this every time. Well, I think you cans ee it a little bit > always but sometimes it is worse. Like the picture shrinks 2cm each side. > > Any thoughts ? > Power supply ripple, probably caused by dried-up electrolytics in the power supply. This used to b
2009-11-23 by WT
My monitor excibits the symptom of a rolling invisible field that shrinks the picture. Like this : NormalNormalNormalNormalNormal SmallSmallSmallSmallSmall NormalNormalNormalNormalNormal NormalNormalNormalNormalNormal NormalNormalNormalNormalNormal NormalNormalNormalNormalNormal
2009-11-23 by Jean-Bernard EMOND
Yes for me is Video DRAM problems... on Q219 JB Le 22 nov. 09 à 23:13, Gordon JC Pearce a écrit : > > dvdborn wrote: > > Since a while my IIx has vertical lines across the screen. > > > > You can see a picture of it here: http://kunst.phl.be/~dvdborn/ > fairlight/vertical_lines_I
2009-11-23 by Fairlight-CMI@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the Fairlight-CMI group. File : /pdf Manuals and others/Mitsubishi M2896-63.PDF Uploaded by : lancelink84 Description : Mitsubishi M2896-63 OEM Floppy Disk Drive Manual
2009-11-23 by xirin6
I am looking for a series III. I have a fully functional excellent condition Technos Axcel. Please let me know if your are interested pm me. I am located in the United States. Kevin
2009-11-23 by Glenn
After a hopeful reseating of a Q219, that'd be my first guess too: video ram, first, then the gizzards that surround it:) - Currently enjoying the Ryiuchi Sakamoto "Neo Geo" vid from your dvdborn page, first heard him in his work with Roddy Frame (w/ Fairlight, I believe, on "Dre
2009-11-22 by Gordon JC Pearce
dvdborn wrote: > Since a while my IIx has vertical lines across the screen. > > You can see a picture of it here: http://kunst.phl.be/~dvdborn/fairlight/vertical_lines_IIx.JPG > > Does anybody know which component in particular is the culprit? > > David > http://dvdborn.blogspot.
2009-11-22 by dvdborn
Since a while my IIx has vertical lines across the screen. You can see a picture of it here: http://kunst.phl.be/~dvdborn/fairlight/vertical_lines_IIx.JPG Does anybody know which component in particular is the culprit? David http://dvdborn.blogspot.com
2009-11-21 by Rob Puricelli
http://www.fairlightinstruments.com/links.html From: Fairlight-CMI@yahoogroups.com [mailto:Fairlight-CMI@yahoogroups.com] On Behalf Of Rob Puricelli Sent: 21 November 2009 13:37 To: Fairlight-CMI@yahoogroups.com Subject: RE: [Fairlight-CMI] CMI playlist This list was also chosen
2009-11-21 by Rob Puricelli
This list was also chosen by Peter Vogel for inclusion in the new Fairlight CMI 30A pages :o) From: Fairlight-CMI@yahoogroups.com [mailto:Fairlight-CMI@yahoogroups.com] On Behalf Of Rob Puricelli Sent: 21 November 2009 13:34 To: Fairlight-CMI@yahoogroups.com Subject: RE: [Fairlig
2009-11-21 by Rob Puricelli
You may also want to check out this playlist I compiled for Spotify, called “All The Fun Of The Fairlight”… http://sharemyplaylists.com/failed-musos-all-the-fun-of-the-fairlight/ Rob. From: Fairlight-CMI@yahoogroups.com [mailto:Fairlight-CMI@yahoogroups.com] On Behalf Of tomulcah
2009-11-20 by tomulcahy
I compiled this: http://www.madtheory.com/wordpress/?p=124 Interestingly, I think they're all IIx.
2009-11-19 by C
I'm looking for a CMI-02 card for a IIx. Thanks!
2009-11-17 by WT
Hi Glenn ! thanks for the info. This was what I was looking for. I have replaced my damaged Q219 card and didn´t make a note where the two cables where attached. I´ll await others to confirm your info before connecting and powering up. ( though the servicemanual states that both
2009-11-17 by Glenn
I can check more in depth later (have to run and can't trace where each cable goes till later), if needed/desired, but fwiw*, on mine* the connector with 2 wires running to it is on the lower of the two connectors on the Q219, facing the front of the mainframe, the one with a sin
2009-11-17 by WT
Which goes where ? I stupidly forgot to mark the two cables going to/from monitor and graphicspen. Duh..... WT
2009-11-16 by Malte Rogacki
Hello, thanks to everyone giving suggestions and suppliers for the battery. I've found a local (German) mail oder store from which I will order a new battery; this will hopefully cure the date problem. -- Malte Rogacki
2009-11-09 by Harald Feldmann
Hi Glenn :) You're welcome. n stands for NanoFarad. I checked again, but could not see the elcos in the diagrams, it may be in a different version ? Anyhow, good luck rebuilding, I removed all my batteries before they leaked and left them that way. Best regards, Harald > Thanks m
2009-11-09 by Bill
Hey Malte in the states: http://www.tnrbatteries.com/tatlbhite1wa.html i have replaced this bettery - thank goodness my III still rocks. all the best to Fairlight people Billyrock --- In Fairlight-CMI@yahoogroups.com, Malte Rogacki wrote: > > Hello everyone; > > I assume the batt
2009-11-09 by Glenn
Thanks man!, really appreciate it!Sorry if this is ignorant but is the "n' on c19 for microfarad or is that picofarad, can never remember the markings on caps. no you're totally right about C9 it's 4.7µ, on the 47 microfarad I was wondering about the blue ones that line most boar
2009-11-09 by Harald Feldmann
Hi Glenn, Without warranty, here are the schematic values: CR 4 and 5 are 5 volt Zener diodes, part MBR 120p R16 = 100 K R13 = 470 R C16 = 10 n C17 = 1 micro polar What is the item number for that philips capacitor ? C9 = 4,7 micro polar Haven't seen any 47 in the schematics for