Yahoo Groups archive
Messages
Page 111 of 114 · 5656 messages matched
2002-06-09 by daryl groetsch
I'm almost done building the digital noise module, except I can't find the 4006 IC very easily. Any comparable replacements? I'm also not 100% sure where the potentiometer hooks up. Is it at CLKO? Thanks, Daryl __________________________________________________ Do You Yahoo!? Yah
2002-06-09 by sasami@hotkey.net.au
No reason at all why you couldn't add the extra reset input. It was only left out for "economic" reasons, namely, with the extra chip and time involved, I couldn't be bothered :)! This module after all was never intended as something for selling. Ken >I want to add an extra reset
2002-06-08 by vtl5c3
I want to add an extra reset input, identical to the one labelled Bank Reset, so that I can reset the wave counter separately. Since I'm going to be using two gates from a CD40106, I thought I'd use the extra gates as square LFOs, so that I have four square wave sources built int
2002-06-07 by sasami@hotkey.net.au
You don't need to use any specific gnd pad. I usually run a wire from one of the gnd pads to the first jack, then a wire from that jack to the next and so on, and don't use the other gnd pads at all. One pot pag goes to the center, the other to the right terminal, when looking at
2002-06-06 by mmarsh100
All righty - I get burst when I connect an external clock. Yippee! Sounds cool, too. But it does point to me hooking the rate pot backwards, I think. I'll dig into this and see. Mike --- In cgs_synth@y..., "mmarsh100" wrote: > Thanks, Ken. I get Trigger out, but no burst. I've pr
2002-06-06 by mmarsh100
Thanks, Ken. I get Trigger out, but no burst. I've probably got something backwards (which POT out goes to which lug on the pot? Does CLK O go to the top lug or the right lug? Which of the 3 GRDs go to jacks? That kind of thing). I'll troubleshoot and let you know. Mike --- In cg
2002-06-06 by sasami@hotkey.net.au
There is no bug fix on the Burst Generator. The jumpers in the photo are connecting the unassigned LED to the selected output. Most likely you have a construction error - a solder bridge, bad joint or whatever. Ken >Hello All - > >I just finished the BG hooked it up and no joy. L
2002-06-06 by mmarsh100
Hello All - I just finished the BG hooked it up and no joy. Looking at the docs, there appears to be two jumpers (bug fixes) on the back of the board. I didn't see this documented but I suspect that I need to do this. I get an oscilloscope on Monday so I can check the output then
2002-05-14 by Matthias Schwarz
Hi everybody, I thought I make a good deal when I bought some SSM2013 VCA IC´s (they were cheap, so it´s ok ;-) But my test-pcb´s always fail. Has anyone ever worked with this device, or is anyone able to check it with a surely working pcb? In my opinion the datasheet must wrong
2002-05-07 by tsomneevich
Hi everyone, and apologies for the cross-posting, but I have a few extra panels in the MOTM format from Schaeffer if anyone's interested. They're $25 each post-paid in the US, which is what I figured I paid for them. They are: 2 Ken Stone Dual Psycho LFO's w/ 4-way multed outs, (
2002-05-05 by sasami@hotkey.net.au
Most certainly they would be okay. Over here they are sold as the same thing most of the time. Ken >How important is it to use LF353s for the Suboscillator? Would >TL072s be ok? > > > > > >See the following URLS for the CGS Modular Synth home page: > http://198.164.142.50/~cgs/ >
2002-05-05 by Scott Deyo
www.unicornelectronics.com has cheap ic's. They all work so far :) >From: Jeffrey Pontius jpont@... > >Reply-To: cgs_synth@yahoogroups.com >To: cgs_synth@yahoogroups.com >Subject: Re: [cgs_synth] parts >Date: Fri, 3 May 2002 08:03:19 -0500 (CDT) > >Daryl, > > > The Semi's I will
2002-05-05 by vtl5c3
How important is it to use LF353s for the Suboscillator? Would TL072s be ok?
2002-05-03 by daryl groetsch
Thaks for the great tips everyone. I'm off and running now! Daryl __________________________________________________ Do You Yahoo!? Yahoo! Health - your guide to health and wellness http://health.yahoo.com
2002-05-03 by Jeffrey Pontius
Daryl, > The Semi's I will just be hunting down! Does anyone > have any suggestions for getting parts in the US other > than at Radio Shack? > If you have web access, there are several companies that are popular and quite reliable: [I suggest these two first] Mouser: www.mouser.c
2002-05-03 by sasami@hotkey.net.au
>Hi, I'm pretty new at this, just received my Digital >Noise and Super Psycho Mod Source PCBs and had a few >questions about the parts lists, if anyone can help. > >Capacitors: if listed 15n, what does the "n" refer to, >nano? What does 2n2 mean? 10uF is 10 micro Farad, but >what
2002-05-03 by daryl groetsch
Hi, I'm pretty new at this, just received my Digital Noise and Super Psycho Mod Source PCBs and had a few questions about the parts lists, if anyone can help. Capacitors: if listed 15n, what does the "n" refer to, nano? What does 2n2 mean? 10uF is 10 micro Farad, but what does 0.
2002-05-01 by sasami@hotkey.net.au
>I'm wondering what happened to the site. The link I have is >broken, and the temporary site has popups for all sorts of cr#p! I am allowed to use the primary server as a favor from another DIYer. THe thing has corrupted itself and needs rebuilding, so I have no choice but to wai
2002-05-01 by elle_webb
I'm wondering what happened to the site. The link I have is broken, and the temporary site has popups for all sorts of cr#p! Is the site at a new location?
2002-04-30 by sasami@hotkey.net.au
> I am already thinking about a companion module to the Dual Psycho LFO >adding seprate rate controls to each LFO and if it's possible switches >to bring the LFO's into the audio range, anyone know how to do that? Check the Super Psycho circuit diagram. Each LFO is equiped with a
2002-04-30 by l8xbass
OK, First, I added a pic of my new Dual Psycho LFO, look in the photo section. I finished the psycho LFO and let me say it is so COOL! Many Many thanks for Scott Deyo for designing and ordering the panel from Schafer. If Scott has any panels left I suggest getting one from him an
2002-04-27 by cgs_synth@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the cgs_synth group. File : /CGS Exports to Modcan Panels/Gate Sequencer to Modcan.jpg Uploaded by : cyndustries cynthiawebster@... > Description : As an Export - to Mod
2002-04-27 by cgs_synth@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the cgs_synth group. File : /CGS Exports to Modcan Panels/Gate Sequencer_ala Modcan.jpg Uploaded by : cyndustries cynthiawebster@... > Description : As an Export - to Mo
2002-04-22 by Scott Deyo
Funny you ask; I just got the panels from Schaeffer today. I have a problem in the design of my burst gen/ psycho panel. The topmost jacks are too high; the board doesn't really fit. I might try punkrocking it at an angle; I don't think it's too extreme. I'll let you know when I
2002-04-22 by cyndustries
Thanks for confirming the switch numbers Scott! Say, how is yours working? Have you finished it, (and if so, what's hooked-up to)? Warm Regards, Cynthia --- In cgs_synth@y..., "Scott Deyo" wrote: > > Hi Cynthia, > > Actually, the 105-2454 is the tested and correct pcb version. 10
2002-04-21 by Scott Deyo
Hi Cynthia, Actually, the 105-2454 is the tested and correct pcb version. 105-1471 is the solder terminal version. I tried the Xicons too, but they don't fit. Scott ----Original Message Follows---- From: "cyndustries" cynthiawebster@... > Reply-To: cgs_synth@yahoogroups.com To: c
2002-04-21 by cyndustries
Burst Generator 12-Position Rotary Swich? Hi Everyone! After reading all the posts from a search of the archives for "Rotary Switch" ... I'm so confused! Please, could someone suggest the correct Mouser Part number for the "Yankee" version of the Apha 12-position rotary switch ne
2002-04-19 by cyndustries
Hi Everybody! See the new GCS13 Gated Comparator Panel graphic on Ken's Gated Comparator page, or see both it - and a similar export of the CGS06 Burst Generator (also to Modcan Panel Format ) in the Files section of this site... > Hi Cynthia, > > I'm just checking that you are a
2002-04-18 by cgs_synth@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the cgs_synth group. File : /CGS Exports to Modcan Panels/CGS06_Burst Generator.jpg Uploaded by : cyndustries cynthiawebster@... > Description : As an Export - to Modcan
2002-04-17 by cyndustries
Hi Everybody! See the new GCS13 Gated Comparator Panel graphic on Ken's Gated Comparator page, or see both it - and a similar export of the CGS06 Burst Generator (also to Modcan panel format) in the Files section of this site... > Hi Cynthia, > > I'm just checking that you are aw
2002-04-17 by cgs_synth@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the cgs_synth group. File : /CGS Exports to Modcan Panels/CGS13_Gated Comparator.jpg Uploaded by : cyndustries cynthiawebster@... > Description : As an Export - to Modca
2002-04-17 by Scott Evans, Gen Mgr
Hi Ken, I am intrigued by some of your offerings (psycho lfo is one). I will be looking into building MOTM versions. Also, just curious: does the shokbox.obscure.ca/~cgs/ point to the 198.164.142.50/~cgs/ site, or are they mirrors? Regards, Scott sasami@... wrote: > > This week I
2002-04-17 by sasami@hotkey.net.au
This week I have decided to offer a couple of boards at a sale price. They are: suboscillator - $5 instead of $10 Preset board for the Gate Sequencer $7.50 instead of $15.00 Have fun! Ken _______________________________________________________________________ Ken Stone sasami@...
2002-04-14 by sasami@hotkey.net.au
Hi all, would anyone who has boards on hold that hasn't yet paid for them, please do so as soon as possible. Those paying via snail mail can ignore this request, because I know you are paying as fast as you can :) Thanks, Ken ______________________________________________________
2002-04-14 by sasami@hotkey.net.au
For those of you asking for a +/-15 volte tube module, here you are. This is a very simple circuit that acts both as a VCA and a wave folder, depending on how hard you drive it. No high voltages involved! Look under "modules", then scroll down to the new modules. Us the secondary
2002-04-12 by sasami@hotkey.net.au
The primary server is on the fritz again, so until we get that sorted, the files can be found at the backup server. http://otherunicorn.0catch.com/synth/ Analogic is now online and available. Digital noise is online and available. Super psychos are in stock for those that missed
2002-04-10 by sasami@hotkey.net.au
I've got the gated comparator article online now. Off to do the next one.... Ken _______________________________________________________________________ Ken Stone sasami@... Modular Synth PCBs for sale http://www.blaze.net.au/~sasami/synth/ > Australian Miniature Horses & Ponies
2002-04-09 by Mitchell Hudson
I'd like to order some PCBs for your new Gated Comparator. Let me know when you update your site, or you can send the pricing info via email. I placed an order about a month ago and have not seen it yet. I'd like to just double check the address and shipping info. Looks like I se
2002-04-09 by sasami@hotkey.net.au
I've had the new boards delivered, but life has had me out every day since! I have completed and tested the much requested Gated Comparator, and are very happy with it. This Gated Comparator is a much improved version of the old one on the web site. Now all outputs are in the ran
2002-04-03 by coyoteous
Analog Modular anamod@yahoogroups.com http://groups.yahoo.com/group/anamod I made this group to learn how to make a group, but also as a joke on a friend who complained that their wasn't such a group. Well, somebody besides me joined (I was going to delete it). The group descript
2002-04-01 by drg3orge
i'd be interested in a through zero VCO. so, what's a VCA based on Electronotes GLAP?? hell, what is GLAP?? i also like jeff's idea 'bout the ASR. dyin' to play with one... i prefer pcb's. it's much nicer to spend $20 now on a gate seq, an' worry later 'bout findin' money for dec
2002-03-31 by harry bissell
Quiet ? I like printed circuit boards the best. I'm unlikely to buy kits... I like some of the suggestions here. An updated wavetable board... maybe with several eprom addresses would be nice. Maybe a one shot wavetable board for drum sounds... with selectable "instruments" as ba
2002-03-31 by Jeffrey Pontius
> > I thought I'd try break the silence. I'd be interested in hearing what > ideas people have for modules that are not available anywhere else, > for possible future inspiration. > Analog shift register with at least 4 shift outputs. I think an ASR would be very useful, not just
2002-03-31 by tsomneevich
1) Shepard Function Generator: 8 triangle waves and 8 sines, each one offset by 45 degrees. Doepfer makes one, but it also has an unnecessary Midi mode, and converting to a larger front panel would strictly suck. A Rate knob and/or cv would be nice. 2) Eprom-switcher daughter boa
2002-03-31 by Meccariello
Hi, I'd like to see some +/-15V tube modules, some more drum modules (with cv controls for pitch & sweep ...) & a parametric equalizer witch voltage controlled boost/cut. Cheers Eugenio ----- Original Message ----- From: catgirlparadise To: cgs_synth@yahoogroups.com Sent: Sonntag
2002-03-31 by RFahl
1)Through Zero VCO. 2)VCA based on Electronotes GLAP. 3)Buchla 259 VCO 4)BJ 4046 based VCO on 3/30/02 11:17 PM, catgirlparadise at sasami@... wrote: Hi all, I thought I'd try break the silence. I'd be interested in hearing what ideas people have for modules that are not available
2002-03-31 by catgirlparadise
Hi all, I thought I'd try break the silence. I'd be interested in hearing what ideas people have for modules that are not available anywhere else, for possible future inspiration. Also, would people be interested in pre-assembled, tested PCBs, or completed modules? There is a pre
2002-03-25 by sasami@hotkey.net.au
It provides AND, NAND, OR and NOR logic functions, but in analog instead of digital. Apparantly the AND and OR functions are the same thing as "peak" and "trough" on the old Serges, and in Modcan's lineup. Feed several voltages into the AND, and the result will be the same as the
2002-03-25 by sasami@hotkey.net.au
My synth site is back up again http://198.164.142.50/~cgs/ Have fun! Ken _______________________________________________________________________ Ken Stone sasami@... Modular Synth PCBs for sale http://www.blaze.net.au/~sasami/synth/ > Australian Miniature Horses & Ponies http://w
2002-03-25 by sasami@hotkey.net.au
Here you go. Ken > Hi I was wondering if you could send me the things for the Burst generator and the Joystick. > >thankyou so much. >almost done with the Burst! > > >See the following URLS for the CGS Modular Synth home page: > http://198.164.142.50/~cgs/ > http://shokbox.obscur