Yahoo Groups archive
Messages
Page 346 of 564 · 28179 messages matched
2006-07-18 by Doepfer_a100@yahoogroups.com
The following Doepfer_a100 poll is now closed. Here are the final results: POLL QUESTION: Would you like Doepfer to release an Additive Oscillator Module?: [32 partials, with a volume value for each. I see it as only having a few principal controls: 5 leds (binary) to show the pa
2006-07-18 by Doepfer_a100@yahoogroups.com
The following Doepfer_a100 poll is now closed. Here are the final results: POLL QUESTION: Would you like Doepfer to release a DIN-Sync to Trigger Interface Module?. [Just a simple thing: - An incoming DIN-Sync should be given as seperate signals on 3,5mm sockets. - The DIN-Sync S
2006-07-17 by beatboxgestapo
No, it not the gain. I tried it with the gain turned down to "1" and I still got it. If I press a key that note will sound until another key is pressed, then it plays that note forever. As for the 606 and SH-101. I have linked them up before, and no problems. I'm starting to thin
2006-07-17 by regimental1200
Are you sure there's not just gain dialed up on the VCA of the A-100 system? As for your 606 and 101 problem, I used to get the same problem with my SH-101. Be it that I was trying to trigger the sequencer from a 606, 808, 909, MAQ, or Schaltwerk, some notes would hang, some woul
2006-07-17 by regimental1200
> I own a Jomox XBase 09, which has a nice swing parameter (though its > resolution is not better than the Schaltwerk): you can draw notes > forward(!) and backward. The "drawing forward" (the note comes earlier > than the original beat) is a very urgent aspect for cool swing stu
2006-07-17 by beatboxgestapo
Hello, I have a Roland SH-101 that I use to control my Doepfer modular system via CV & Gate (not midi). I haven't used it for a while, and I have noticed a problem when I tried to record with it yesterday. There is always a constant tone coming out of the Doepfer even when I am n
2006-07-17 by hardware@doepfer.de
In principle a modular sequencer with separate units for gate/trigger rows and CV outputs is not a real challenge for us as it's very similar to the A-155. But I think it is necessary also to discuss the mechanical solution for such a sub-system as this the critical part from my
2006-07-17 by Bakis Sirros
hello florian, dieter, what about this suggestion? should i create a poll about a 16 step sequencer in two parts(one part for the trigger rows[the three position 16 trigger switches] and the second part for the cv rows?) please, tell me the form that the poll should have, and if
2006-07-17 by Bakis Sirros
hello dieter, ok, i will. best regards, bakis. --- hardware@doepfer.de wrote: > We already had some discussions concerning audio > mixers. I'm not sure if the > A-100 users are willing to pay a much higher price > for an A-100 mixer module > compared to a stand-alone mass-product
2006-07-17 by hardware@doepfer.de
We already had some discussions concerning audio mixers. I'm not sure if the A-100 users are willing to pay a much higher price for an A-100 mixer module compared to a stand-alone mass-production mixer. So you may start a poll but a remark should be added that such a mixer will b
2006-07-17 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to release a Stereo/panning mixer? (it will probably be a four input mixer with level and panning knobs for each of the 4 channels, plus a stereo/two mono master outputs. Remark:
2006-07-17 by q v s f u e k p s v h s l w
has anyone compared the doepfer vactrol to the plan b ? chad_kettering wrote: I have a less than 1 month old Plan B Vactrol Filter for sale on Ebay. Here is the link: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&ih=016&item=260009523917&rd=1&sspagename=STRK%3AMESE%3AIT&rd=1 I al
2006-07-17 by q v s f u e k p s v h s l w
the mpc's and the asq10 i found have ' the ' a swing Florian Anwander wrote: Hi > In terms of groove and swinging, does anyone have an opinion on how > the Schaltwerk compares to the P3 and TR-909? I know some people that > say that the Schaltwerk has absolutely no groove, ie. so
2006-07-17 by Bakis Sirros
hello florian, ok, thanks for the info. so, no need for a poll then. best regards, bakis. --- Florian Anwander wrote: > Hi Bakis, > > I remember, that Dieter answered already once, that > he never could > produce such a mixer in a reasoable price range. > Imagine how much a stand
2006-07-17 by Florian Anwander
Hi Bakis, I remember, that Dieter answered already once, that he never could produce such a mixer in a reasoable price range. Imagine how much a standard mono module with five pots costs and then have a look at the price this one: Florian Bakis Sirros wrote: > so, dieter, should
2006-07-17 by Florian Anwander
Hi > In terms of groove and swinging, does anyone have an opinion on how > the Schaltwerk compares to the P3 and TR-909? I know some people that > say that the Schaltwerk has absolutely no groove, ie. sounds way too > mechanical, no swinging feel available. I have to agree in som
2006-07-17 by chad_kettering
I have a less than 1 month old Plan B Vactrol Filter for sale on Ebay. Here is the link: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&ih=016&item=260009523917&rd=1&sspagename=STRK%3AMESE%3AIT&rd=1 I also have one Doepfer A-111 High End VCO for sale http://cgi.ebay.com/ws/eBayISA
2006-07-17 by Doepfer_a100@yahoogroups.com
The following Doepfer_a100 poll is now closed. Here are the final results: POLL QUESTION: Would you like Doepfer to release an Expansion Module for the a155 and A-154 sequencer modules that makes the A0, A1, A2 addresses and the clock signal of the a155 (4x input, 4x outputs) and
2006-07-16 by Bakis Sirros
and i was thinking "what peacefull group i have..." ok, i do not know who that person is, and what he might have done, or not. please, do NOT send aggresive/personal attack messages like this (with this kind of language) in this group guys. lets keep this group decent as it alway
2006-07-16 by regimental1200
In terms of groove and swinging, does anyone have an opinion on how the Schaltwerk compares to the P3 and TR-909? I know some people that say that the Schaltwerk has absolutely no groove, ie. sounds way too mechanical, no swinging feel available. I have to agree in some regards.
2006-07-16 by Bakis Sirros
hello list, i have set the archives setting to "public". so, from now on, the RSS feature is available for anyone who wants (and knows how) to use this feature. best regards, Bakis. Bakis Sirros - Parallel Worlds [Doepfer_a100] group owner http://www.parallel-worlds-music.com htt
2006-07-16 by davevosh@aol.com
hello to all, 2 pic`s of my doepfer et al modular taken july 2006 have been added to photo`s section. first pic`s i`ve taken since 2003 and the synth has grown a bit - best, dave [Non-text portions of this message have been removed]
2006-07-16 by Doepfer_a100@yahoogroups.com
The following Doepfer_a100 poll is now closed. Here are the final results: POLL QUESTION: Would you like Doepfer to release an Expansion module for all quantizers (hopefully including A-156) for creating scales and arpeggio's? [A module that would probably contain 24 or 32 jack o
2006-07-16 by Doepfer_a100@yahoogroups.com
The following Doepfer_a100 poll is now closed. Here are the final results: POLL QUESTION: Would you like Doepfer to release a Timbral Quantizer Module? [If you check out the relation between the harmonic spectrum of a certain sound (frequency and level of partials) and the interv
2006-07-16 by Doepfer_a100@yahoogroups.com
The following Doepfer_a100 poll is now closed. Here are the final results: POLL QUESTION: Would you like Doepfer to release an Equal Temperament Quantizer Module? [Think of a single A-156 without the three switches, but with one extra added knob (or perhaps two knobs/jack input f
2006-07-15 by Bakis Sirros
hello phil, well, this is not an easy question... the ZO is my most expensive VCO. it is even more expensive than my technosaurus OSHO's. so, for the price you pay, you do get an awesome sounding VCO indeed! it has a really special sound unlike any other vco i have heard! the pla
2006-07-15 by davevosh@aol.com
to all, enclosed please find a current pic of my synth - best, dave (bakis, can you post pic to the "photo`s" section, please ?) [Non-text portions of this message have been removed]
2006-07-14 by Bakis Sirros
so, dieter, should i make another poll about such a module? best regards, Bakis. --- musicagenera wrote: > hallo > I do not know if that was discused before > I miss a lot STEREO / PANING mixer, only one stereo > module available from Doepfer is > paning module, which is quite si
2006-07-14 by levka0
Perhaps the new VCA module from Cwejman is of interest to you ? http://www.cwejman.net/VCA-2P.htm Best regards Joost --- In Doepfer_a100@yahoogroups.com, "musicagenera" wrote: > > hallo > I do not know if that was discused before > I miss a lot STEREO / PANING mixer, only one ste
2006-07-14 by selfoscillate
> Hi Bakis, > how does it sound compared to the m15? > It's seems very tempting, but I love the PlanB m15, and the ZeroOsc only > really sounds tempting to me if I could have 2 or 3, then of course, no > brainer. > The m15 just has such a rich character and 2.5 would cost about a
2006-07-14 by phil hendricks
take a look at the Plan B Model 18 modules? http://www.ear-group.net/planb_start.html best, phil
2006-07-14 by James Husted
I agree. A stereo output module with 4 ins with levels and pan and a master out level is all that is needed. -J On Jul 13, 2006, at 1:18 PM, musicagenera wrote: > hallo > I do not know if that was discused before > I miss a lot STEREO / PANING mixer, only one stereo module > avai
2006-07-13 by musicagenera
hallo I do not know if that was discused before I miss a lot STEREO / PANING mixer, only one stereo module available from Doepfer is paning module, which is quite simple one, of course at least something dont you think that may be more advanced mixer with 2-4 imputs but with L/R
2006-07-13 by p.hendricks
On 7/12/06 9:50 AM, "Bakis Sirros" wrote: > hello list, > just wanted to metnion that two days ago i receivedf > my euro version Zeroscillator(ZO) and it really sounds > fantastic! > it has a VERY rich tone and lots of different timbral > modulation capabilities. Hi Bakis, how do
2006-07-12 by Bakis Sirros
hello list, just wanted to metnion that two days ago i receivedf my euro version Zeroscillator(ZO) and it really sounds fantastic! it has a VERY rich tone and lots of different timbral modulation capabilities. Cyndustries had, at first, some problems with making their initial bat
2006-07-12 by Bakis Sirros
hello james, florian, ok, looks like new polls are on the way... best regards, Bakis. --- Florian Anwander wrote: > Hi > > > A "Rhythm Sequencer" > Yes Yes Yes Yes!!!! > > But see my suggestions for a modular sequencing > system ("ceterum > censeo..."): > This should not be a tri
2006-07-12 by Florian Anwander
Hi > A "Rhythm Sequencer" Yes Yes Yes Yes!!!! But see my suggestions for a modular sequencing system ("ceterum censeo..."): This should not be a trigger sequencer, but a switch sequencer (with DG409). This means for the switch sequencer: Module one: 16 three position switches. Ce
2006-07-12 by James Husted
A newer "Multiples" module: After seeing the poll for the new Buss Access module I thought it would be nice to have a A-183 Multiples 3 module that would be a Dual or Single active one-in-4-out multiple that would be good to fan out to voltage sensitive modules (CV in on VCOs of
2006-07-12 by Bakis Sirros
lately i have problems with some yahoo groups. i sent messages and they never show up in the respective group. so, just testing in my own group... Bakis Sirros - Parallel Worlds [Doepfer_a100] group owner http://www.parallel-worlds-music.com http://www.myspace.com/parallelworldsm
2006-07-11 by synth_freak_2000
sorry, one more test.
2006-07-11 by manlovemusic
-o_o-....hi, levka, how are you? thank for Joost & your infor. 1). oh! i really like the real analog.....cv & gate......but if i have to use va as a vco....i prefer software like es2, reason ,moog v modular then va hard synth...... 2) of course .....PERFOURMER ......i heard some
2006-07-10 by Doepfer_a100@yahoogroups.com
The following Doepfer_a100 poll is now closed. Here are the final results: POLL QUESTION: Would you like Doepfer to release a Bit Processing/ Bit Swapping Module? [a new module with an Analogue to Digital converter, with analogue cv/audio inputs that accept the input analogue sig
2006-07-10 by chad_kettering
Plan B Model 14 *** SOLD **** All Doepfer modules still available!
2006-07-10 by Doepfer_a100@yahoogroups.com
The following Doepfer_a100 poll is now closed. Here are the final results: POLL QUESTION: Would you like Doepfer to release an ARP Filter Module?(based on the 24db ,cascade of integrators, type 4072 or 4075 ARP filter design, but something along the A108 in terms of features/inpu
2006-07-09 by chad_kettering
Hello, I have the following Doepfer modules for sale from the US: A-111 VCO $265 A-111 VCO $265 A-127 Triple Resonant Filter $185 A-114 Ring Mod $60 A-145 LFO $60 Plan B Model 14 Vactrol Filter $200 Shipping will be $10 per module in the US and $30 per module shipped to the UK. A
2006-07-09 by Bakis Sirros
hello matthew, please, if you want that i make a poll about a module in the style of buchla's 296 spectral processor that you mentioned, explain to us what are the special functions of this module. thank you, best regards, Bakis. --- mritenburg wrote: > Here are some ideas: > > 1
2006-07-09 by Doepfer_a100@yahoogroups.com
The following Doepfer_a100 poll is now closed. Here are the final results: POLL QUESTION: Would you like Doepfer to manufacture a Voltage Controlled Police Scanner Module? (a gate signal would trigger the search or scan function, attenuated cv for squelch, volume and tuning and s
2006-07-09 by Doepfer_a100@yahoogroups.com
The following Doepfer_a100 poll is now closed. Here are the final results: POLL QUESTION: Would you like Doepfer to release an Expanded version of A-185 (Bus Access) module? (It should be able to output cv/gate to more busboards than one, and also have a switch to which of the co
2006-07-09 by Doepfer_a100@yahoogroups.com
The following Doepfer_a100 poll is now closed. Here are the final results: POLL QUESTION: Would you like Doepfer to release a General Addon /Mixer-Crossfader module? This should enhance the input/output-features of mostly audio related modules. * For the output I'd like to have s
2006-07-09 by Doepfer_a100@yahoogroups.com
The following Doepfer_a100 poll is now closed. Here are the final results: POLL QUESTION: Would you like Doepfer to release a Resonant EQ Module? (something a bit along the lines to but an advanced version of this: http://www.serge-fans.com/wiz_filt.htm ) CHOICES AND RESULTS - Ye