Re: [CZsynth] Re: Casio CZ5000 Capacitors leaking?
2012-01-08 by Gordon JC Pearce
On Sun, 08 Jan 2012 05:21:31 -0000 ... Electrolytics very, *very* rarely fail unless they are used in hot, poorly-ventilated power supplies. In 20-odd years of
Messages
Browse messages
Page 47 of 145 · 7206 messages matched
Re: [CZsynth] Re: Casio CZ5000 Capacitors leaking?
2012-01-08 by Daniel Forró
Hi, Jim, congratulations to your successful repair! Could you please write me exact type of relay and where have you ordered it here in Japan? Maybe I will
Re: Casio CZ5000 Capacitors leaking?
2012-01-08 by Jim Atwood
Thanks very much for the replies everyone. I went ahead and replaced the malfunctioning Relay and the Casio CZ-5000 is in perfect working order again. The old
Re: [CZsynth] Casio CZ5000 Capacitors leaking?
2012-01-07 by Steve Tomporowski
I ll second that. It seems strange that it is only on the 3 larger capacitors. Usually if a cap goes, it s the top (see the triple split at the top?) that
Re: [CZsynth] Casio CZ5000 Capacitors leaking?
2012-01-07 by Bob S.
Hi. Does not look like leakage to me, probably a glue used during assembly to keep the heavy component in place when they flip the board over to solder......
Casio CZ5000 Capacitors leaking?
2012-01-07 by Jim Atwood
Hi everyone, I opened up my Casio CZ5000 to replace the Omron relay after receiving a replacement here in Japan. I noticed three Capacitors that had this green
Re: Need help fixing relays of my CZ-1 please...
2012-01-07 by fab8soul
Thanks Gordon! I am off to the electronics shop :-)
Re: Need help fixing relays of my CZ-1 please...
2012-01-06 by fab8soul
THANKS a lot! For me it is definitely the crackle noise and low volume. I did see your posting about how to open the CZ... I think I can do it now! Good luck
Re: [CZsynth] Re: Need help fixing relays of my CZ-1 please...
2012-01-06 by Gordon JC Pearce
On Fri, 06 Jan 2012 09:28:33 -0000 ... If it s the same as the relay in the CZ1000, then all it does is mute out the audio for a second or two so it doesn t
Re: Need help fixing relays of my CZ-1 please...
2012-01-06 by scituate_mass
Hi Fab8, I used the part mentioned in my earlier post here: http://launch.groups.yahoo.com/group/CZsynth/message/4468 This is the part, and it is supposed to
Re: Need help fixing relays of my CZ-1 please...
2012-01-06 by fab8soul
Thanks for this! I think I will be able to identify the relays now... If anyone has a precise info on where they are located, would be helpful though. I
Re: [CZsynth] Need help fixing relays of my CZ-1 please...
2012-01-06 by Lee Borrell
http://2.imimg.com/data2/SD/JY/MY-2393894/iw85s8h2-250x250.jpg http://www.relays.cc/images/electric-relay-4078.jpg I have not been inside a CZ1 - above are
Need help fixing relays of my CZ-1 please...
2012-01-05 by fab8soul
Hi everyone, after having read through the variuos posts in this forum, I am pretty sure that I have this classical relay problem. In theory I understand
Re: CZ Editor for Mac??
2012-01-02 by Jan Hudak
Hello, did you tryied MidiQuest 10 ? On DVD is also large collection of sysEx sounds for the casio synths. http://www.soundquest.org/ Have nice day. Jan
Re: CZ Editor for Mac??
2011-12-22 by fab8soul
Hi there! I have the same problem... I found this editor, but not sure whether it works all that well, but it is free! I have not tried it yet as I first have
Re: Casio CZ-101 Display with backlight
2011-12-19 by uldiszemzars
Thanks! I did that, now i waiting email fro them.
Re: [CZsynth] Re: Casio CZ-101 Display with backlight
2011-12-19 by jammie
no you dont just pass that and carry on adding your details that is only if you have brought from them before as you would have a account number just register
Re: Casio CZ-101 Display with backlight
2011-12-19 by uldiszemzars
OK, but i can,t bay OLED in eBay! I tried registration to rapidonline.com, but i can,t! There i need stupid Rapid account number - what is that? Maybe i can
Re: [CZsynth] Re: Casio CZ-101 Display with backlight
2011-12-19 by jammie
the problem with these displays is you have to do surgery to the machine in adding 5v for the led display plus the led displays are 7mm thicker which means
Re: Casio CZ-101 Display with backlight
2011-12-18 by uldiszemzars
This will be right?: http://www.rapidonline.com/Electronic-Components/16x2-Oled-Display-Yellow-85x36x10mm-57-2298/?sid=64f37e44-89e6-431c-8ddb-81c645b8a25e
Re: [CZsynth] Re: Casio CZ-101 Display with backlight
2011-12-18 by jammie
no that is not the display the display is an oled 16x2 WEH001602C (85x36) and its from rapidonline.com ... From: uldiszemzars To: CZsynth@yahoogroups.com Sent:
Re: Casio CZ-101 Display with backlight
2011-12-18 by uldiszemzars
And here is many with different light: http://global.ebay.com/Character-LCD-Module-Display-16X2-1602-Compatible-HD44780/200659769398/item
Re: Casio CZ-101 Display with backlight
2011-12-18 by uldiszemzars
Thank You for many info!!! This LCD will be OK for Casio CZ-101 upgrade:
Re: [CZsynth] Casio CZ-101 Display with backlight
2011-12-14 by jammie
theres a new 1 for 1 replacement and its a yellow led writing on black background they are oled dont need the angle connection as they are good from any angle
Re: [CZsynth] Casio CZ-101 Display with backlight
2011-12-14 by Lee Borrell
It was probably a mod that was done on it - I kept the email from this forum regarding doing the mod as I had probably too high hopes of doing it: It s just a
Casio CZ-101 Display with backlight
2011-12-13 by uldiszemzars
Where can i get Casio CZ-101 Display with backlight? I saw in eBay one man sold Casio CZ-101 with backlight display.
Re: [CZsynth] Re: More cz goodness
2011-12-07 by charlie 'chop' copp
yep ! you are right , but just to add the cz in mono ,mode will play 4 voices on 4 indipendant channels,,, so some legato /duration will be obtainable... yahoo
Re: [CZsynth] Re: More cz goodness
2011-12-06 by Daniel Forró
This technique has some limitations: - can be used only in non legato music, where notes are not overlapping. Chords are possible. - PC must be send slightly
Re: [CZsynth] Re: More cz goodness
2011-12-06 by Lee Borrell
I like the lightshow idea! Of course if you have a Yamah PSR or Casio LK etc then you get the same thing. The other way of enabling patch changes on notes is
Re: [CZsynth] Re: More cz goodness
2011-12-06 by Phillip White
there is no such thing as a specific program change on every note function. prog changes are included in the MIDI spec so are not a function per se of the
Re: [CZsynth] Re: More cz goodness
2011-12-06 by charlie 'chop' copp
i too find interest in the program change .. utilize , optimize...maximize ,,is my belief... and believe it or not i got a couple of my original midi files
Re: [CZsynth] Re: More cz goodness
2011-12-04 by Peter Sedin
cool! does cz has a programn change on every note thingy?? 2011/12/4 hector ... -- Mvh Peter H.K Sedin [Non-text portions of
Re: More cz goodness
2011-12-04 by hector
Of course its strange. Its meant to be strange. It is a slice from a song called Hole in the Ozone layer and if you think the instrumentation is bad then you
Re: [CZsynth] More cz goodness
2011-12-03 by charlie 'chop' copp
hector this is strnge music ..what was it for? charles ... From: hector To: Sent: Sunday, November
Re: CZ3000
2011-11-23 by steve_the_composer
Sorry if my reply confused you. I was replying to the original post, not your reply. I guess I could have made that clearer. Steve
Re: [CZsynth] Re: CZ3000
2011-11-23 by Mike Ward
I will do this and let you know the results. Thanks. ________________________________ From: Daniel Forró To: CZsynth@yahoogroups.com
Re: [CZsynth] Re: CZ3000
2011-11-23 by Daniel Forró
Exactly what I have written. Daniel Forro
Re: CZ3000
2011-11-23 by steve_the_composer
PS: (1) I would be very curious to know if doing a reset solves the problem. (2) I could be wrong, but so far as I remember, you need to load the patch data
Re: CZ3000
2011-11-22 by steve_the_composer
I wrote an extensive reply to this, but evidently Yahoo Groups posting system must have crapped out. Maybe I will try to repost it one of these days. In short:
Re: [CZsynth] Re: power but no sound
2011-11-21 by Lee Borrell
The reset button is recessed and looks like a screw hole in the base - close to the rear right foot - it is marked P - pressing this with a thin pen will
Re: power but no sound
2011-11-20 by Alan
Thanks, I couldn t find the reset button, How do yoyou use the initalise button, AlanO
Re: [CZsynth] power but no sound
2011-11-20 by Lee Borrell
Have you tried the reset underneath the unit or loading default parameters using the INITIALISE button? ________________________________ From: Alan
power but no sound
2011-11-20 by Alan
Got my Cz 1000 out of the closet after we moved it had been setting for about 3 month s. I turned it on the power came on but no sound of any kind. any ideas??
Re: More cz goodness
2011-11-20 by s0lstice57
Thank you for these tracks ! Here is a song made with the Casio CZ-101 :Casiokids - Golden Years-
More cz goodness
2011-11-20 by hector
Heres some cz101 from something i was working on in the late 80 s http://web.aanet.com.au/cupcake/cz/ozone.mp3
Re: [CZsynth] Semi-OT: My electro-pop duo from the mid-1980s!
2011-11-20 by Gordon JC Pearce
On Sun, 20 Nov 2011 01:02:48 -0000 ... It s very much of its time, and you can tell it s good because the B-side is better ;-) (four plays later) I ve got a
Semi-OT: My electro-pop duo from the mid-1980s!
2011-11-20 by Simon Beck
I ve finally digitised the songs from Mix It Up s debut (and only) record, the 4-song EP Mickey Reform , and put together a web page about the band. All the
Re: Converting a Casio CZ tone to a CZynthia preset
2011-11-19 by s0lstice57
Hello ! I just read your answer. I see--it is not free. - CZynthia isn t free, right. Note: While this VSTi is inspired by the original Casio CZ series of
RE: [CZsynth] CZ3000
2011-11-19 by Mike Ward
Yes, there is data. I can press A1 and sees BRASS ENS.1 and it plays through the AMP. From: CZsynth@yahoogroups.com [mailto:CZsynth@yahoogroups.com] On Behalf
Re: [CZsynth] CZ3000
2011-11-19 by Daniel Forró
Sorry to say so obvious thing but are you sure there are some data in banks A and B? I write this because I had similar problem with CZ3000. There s backup