Yahoo Groups archive
Messages
Page 358 of 564 · 28179 messages matched
2006-05-06 by Bakis Sirros
ok list, it is brainstorm time again! if you have any crazy idea about a future exotic A100 module, just say it! i'll gather all your ideas during the next two weeks and out of them i'll create some new polls. i am waiting... best regards, Bakis. Bakis Sirros - Parallel Worlds [D
2006-05-04 by vliesgaard
Thanks for the exelent service. --- In Doepfer_a100@yahoogroups.com, "Dieter Doepfer" wrote: > > Dirk, > > it took a while but now we found the reason and a solution ... > > We had problems to understand why the combination of A-110 (rectangle)/A-113 > is working perfect but not
2006-05-04 by Dieter Doepfer
I assume that it has to do with AC/DC coupling of the audio in/outputs. It is important to know if you use the old version of A-131 (with CEM3382) or the new one (with CA3080). The old versions of A-130/A-131 had AC coupled in/outputs as this was a precondition of the CEM3382. In
2006-05-03 by Louis van Dompselaar
I recently noticed that if I connect my Digisound 80-6L or EFM VCF7 to the A-131 and use a short attack I get loud clicks from the VCA, quite different (and a whole lot louder) than the short click I'm used to getting with zero attack. Could this be due to some interaction or bad
2006-05-03 by Anton Coops
> I don't know the A-101-3 in detail, but as far as I know (I am not 100% > sure about this!) the Mutron had a kind of compression circuitry, which > is not included in the A-101-3 and which might be simulated with > additional modules. Hi Florian, Jose My personal uneducated gue
2006-05-03 by Dieter Doepfer
Dirk, it took a while but now we found the reason and a solution ... We had problems to understand why the combination of A-110 (rectangle)/A-113 is working perfect but not A-111(rectangle)/A-113 at low frequencies. Strangely enough the combination A-111(sawtooth)/A-113 causes no
2006-05-03 by Florian
Hi Jose, > How is the sound of the Doepfer phasers A-101-3 and A-125 compared to older > units like Roland, Mutron and the like? The classic Mutron Bi-Phase sound is > outstanding, but I just want more cv control over the parameters. The A-125 sounds like the middle class stomp b
2006-05-02 by selfoscillate
hello nicolas, during the weekend i tried to reproduce the vowel table mentioned in the a127 manual, using an a127 pcb version 3. i have to point out that these settings may vary from module to module, due to component tolerances or module revisions. use these values as a guide o
2006-05-01 by Anton Coops
The classic Mutron Bi-Phase sound is > outstanding, but I just want more cv control over the parameters. Hi Jose, If you want to you can make the 101-3 sound so much like the mutron biphase you'll only hear the difference - the lack of a certain shimmer - if you compare a/b, but
2006-04-30 by José Sogo Flores
Hi, How is the sound of the Doepfer phasers A-101-3 and A-125 compared to older units like Roland, Mutron and the like? The classic Mutron Bi-Phase sound is outstanding, but I just want more cv control over the parameters. Regards Jose
2006-04-30 by untiedstates
To try and be helpful here, I'd suggest that you start with the absolute necessities for what you want to do and build out from there, tailoring the system to your needs. From the Frusciante clip and what you're saying, for example, you absolutely need an A-119 external input / e
2006-04-30 by Michael Wagner
*Lurk mode off* Hi Chris, You should probably take my suggestions with a grain of salt since I only recently got my first Doepfer modules and I'm a newbie in the modular world. But I don't want you to have this request unanswered and don't want you to be frustratet, becaus you bo
2006-04-30 by ALX002
Hi STuah!!! Think that NEW MCV4's are sold at 110 Euros !! www.doepfer.de ALex --- stuadh a écrit : --------------------------------- Hi, I have a fairly new (2 year old) MCV4 in excellent condition for sale. It includes a 230V power supply and patch leads giving 2 Gates and 4 ot
2006-04-29 by stuadh
yes, but they cost £85 plus p+p in the UK. --- In Doepfer_a100@yahoogroups.com, ALX002 wrote: > > Hi STuah!!! > > Think that NEW MCV4's are sold at 110 Euros !! > > www.doepfer.de > > ALex > > > --- stuadh a écrit : > > > --------------------------------- > Hi, > > I have a fairl
2006-04-29 by Christopher Scullion
Hi, I am new here. I have no previous experience with A-100 synths but am thinking of buying one. I have been reading up about them and I am thinking of getting one of the basic systems, System 1 or System 2, but I am not too sure if they will be able to do what I am hoping they
2006-04-29 by stuadh
Hi, I have a fairly new (2 year old) MCV4 in excellent condition for sale. It includes a 230V power supply and patch leads giving 2 Gates and 4 other CV outputs. The Manual can be found on the Doepfer website at http://www.doepfer.de/pdf/MCV4_man.pdf. The asking price is £70 plus
2006-04-29 by deastman2
Dieter, Thank you for tracking down the source of this problem. I should be able to make the modifications myself, but I want to be clear about what needs correcting. You mentioned adding a capacitor to the A-140 (ADSR) board. Do I really need to modify every module which might r
2006-04-28 by Dieter Doepfer
David, we found the reason for the problem. After all it's logical but it took a while to find it out. Technical explanation: when the clock signal appears (positive transition) it takes a while until the processor outputs the new address to the multiplexers. During this short ti
2006-04-27 by Dieter Doepfer
Florian, should be no problem. There are already some 3mm threads for such purposes available at the R2M manual housing. Best wishes Dieter P.S. barbecue season ahead ! I hope it will work this year ;-) > -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com > [ma
2006-04-27 by vliesgaard
--- In Doepfer_a100@yahoogroups.com, "Dieter Doepfer" wrote: > > OK, I'll check this with an A-111 and A-113. But it may take a few days as > we are very busy with testing and modifying the BBD modules as the customers > are waiting anxiously for their modules. > > Best wishes >
2006-04-27 by Florian Anwander
Hi Bryan > I'd like to get one of these and use it with a guitar strap so I > can jump arround like a madman when I perform. Exactly this is what I intended to do with it ;-) @Dieter: is it possible to add strap click buttons to the housing from the mechanical point of view? At l
2006-04-27 by David Salter
Yeh, Keith Emerson eat yor heart out :) David Salter Senior Project Manager Reuters Ltd Tel +44 20 7542 2402 Mob +44 7990562402 email david.salter@reuters.com RM david.salter.reuters@reuters.net ________________________________ From: Doepfer_a100@yahoogroups.com [mailto:Doepfer_a
2006-04-26 by Dieter Doepfer
Gino, the shorter one at the Musikmesse had 1024 stages, the longer one 2048 stages (the other BBD circuits arrived after the Musikmesse). Best wishes Dieter Doepfer > -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com > [mailto:Doepfer_a100@yahoogroups.com]Im
2006-04-26 by Robair, Gino
On 4/25/06 3:43 PM, Ingo wrote: > if you want all effects, you will > have to buy more than one version (a small and a large one?). I was afraid you'd say that! :-) > the best allrounder is probably the 1024 stages version, > but i can only speak for myself here. I'll check that
2006-04-26 by Bryan E Cornell
When that mythical time arrives when I actually have some money, I'd like to get one of these and use it with a guitar strap so I can jump arround like a madman when I perform. Bryan >>> david.salter@reuters.com 04/26/06 10:54 AM >>> Agreed a very cool device. Let us all know how
2006-04-26 by David Salter
Agreed a very cool device. Let us all know how you find the midi side of the unit. Best wishes David David Salter Senior Project Manager Reuters Ltd Tel +44 20 7542 2402 Mob +44 7990562402 email david.salter@reuters.com RM david.salter.reuters@reuters.net ________________________
2006-04-26 by Florian Anwander
Hi David, > Are you referring that one or the midi version? I've not tried the midi > version but am very tempted as I expect it would make my Waldorf Pulse > sing. I have the midi version, but I did not try it with MIDI yet. But nevertheless it will be an amazing performance wit
2006-04-26 by David Salter
Florian, I purchased the ribbon controller (original CV model) when it was first issued and it is a great piece of kit. Are you referring that one or the midi version? I've not tried the midi version but am very tempted as I expect it would make my Waldorf Pulse sing. David David
2006-04-26 by Florian Anwander
Sorry that I jump in here a littlebit without a cause, but I have to tell it somebody... Since two days I have a Doepfer ribbon controller and I am overwhelmed. This opened really new doors in playing a synthesizer! I slept only two hours this night, because I played on and on an
2006-04-26 by Dieter Doepfer
Ingo, thank you. You are right. Only 128 and 4096 stages are affected. Dieter > -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com > [mailto:Doepfer_a100@yahoogroups.com]Im Auftrag von selfoscillate > Gesendet: Mittwoch, 26. April 2006 12:40 > An: Doepfer_a100@
2006-04-26 by Dieter Doepfer
Because we had some inquiries I have to point out that it is not possible to order a modified module of the first two series and exchange it later for a non-modified module from the third series (~June 2006). If you want to have an A-188-1 with 128, 256 or 4096 stages without the
2006-04-26 by Dieter Doepfer
OK, I'll check this with an A-111 and A-113. But it may take a few days as we are very busy with testing and modifying the BBD modules as the customers are waiting anxiously for their modules. Best wishes Dieter Doepfer > -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yaho
2006-04-26 by selfoscillate
hello all, it seems that dieter's message had a little typo in the first part. modifications on the first and second series of bbd-modules are only necessary for 128 and 4096 stages ic's. 256 stages modules do not need any modification. best wishes ingo --- In Doepfer_a100@yahoog
2006-04-26 by vliesgaard
--- In Doepfer_a100@yahoogroups.com, "Dieter Doepfer" wrote: > > Dirk, > > does this problem occur with the A-111 only or even with A-110? And are you > sure that you shortened C10 (not C9, C9 is responsible for AC coupling of > the sawtooth) ? > > Best wishes > Dieter Doepfer >
2006-04-25 by Christopher Scullion
Hi, I am new here. I have no previous experience with A-100 synths but am thinking of buying one. I have been reading up about them and I am thinking of getting one of the already built ones, System 1 or System 2, but I am not too sure if they will be able to do what I am hoping
2006-04-25 by Dieter Doepfer
Dirk, does this problem occur with the A-111 only or even with A-110? And are you sure that you shortened C10 (not C9, C9 is responsible for AC coupling of the sawtooth) ? Best wishes Dieter Doepfer > Hello Dieter, > > I've just shorted C10 on my A-111. > > But the A-113 still ha
2006-04-25 by Dieter Doepfer
Originally the BBD module A-188-1 was planned only for two types of BBD circuits which are still in production: 1024 and 2048 stages. But we decided to offer the module even with obsolete BBD circuits as long as quantities last they can be used as well (unfortunately with some mo
2006-04-25 by Dieter Doepfer
Gino, it's hard to explain the differences - aside from those which are obvious (longer delay times with longer BBDs). And this is why Ingo made the sound examples and I really thank him for this as I would not have the time. In general shorter BBDs are better if you prefer to em
2006-04-25 by Dieter Doepfer
Sorry - we do not offer boards without front panels but only completely assembled and tested modules (with or without BBD circuit). The empty boards a few weeks ago was an exception because of the ROHS change. Pay attention that the BBDs of the MN3xxx series are not fully compati
2006-04-25 by selfoscillate
hello gino, as dieter said, it's difficult to explain. as soon as you dial in large amounts of feedback, the smaller bbd's have advantages soundwise, because their resonance sounds cleaner (less distortion). on the other hand the bigger bbd's are more versatile because of the lon
2006-04-25 by selfoscillate
--- In Doepfer_a100@yahoogroups.com, "vliesgaard" wrote: > > --- In Doepfer_a100@yahoogroups.com, davevosh@ wrote: > > > > > > In a message dated 4/24/2006 2:21:26 AM Pacific Standard Time, > > hardware@ writes: > > > > > > > > you are right. It's the same matter. The rectangle o
2006-04-25 by selfoscillate
--- In Doepfer_a100@yahoogroups.com, "ph@..." wrote: > > On 4/24/06 2:35 PM, "Robair, Gino" wrote: > > > Thanks for the examples, Ingo. > > Here's a strange question for you (and Dieter, if has some thoughts about > > it): how does one determine which bbd (which number of stages)
2006-04-25 by selfoscillate
--- In Doepfer_a100@yahoogroups.com, "nicholas_kent" wrote: > > So far I've just played with it by ear. > > But I'm curious if anyone has already worked out tables or a formula to center any one of the > BP filters on a particular Hz. frequency. > > I was kind of annoyed the that
2006-04-25 by vliesgaard
--- In Doepfer_a100@yahoogroups.com, davevosh@... wrote: > > > In a message dated 4/24/2006 2:21:26 AM Pacific Standard Time, > hardware@... writes: > > > > you are right. It's the same matter. The rectangle output of the A-111 is AC > coupled (capacitor between the rectangle out
2006-04-25 by ph@comcast.net
On 4/24/06 2:35 PM, "Robair, Gino" wrote: > Thanks for the examples, Ingo. > Here's a strange question for you (and Dieter, if has some thoughts about > it): how does one determine which bbd (which number of stages) to purchase, > without hearing and trying each one? Is it possib
2006-04-24 by nicholas_kent
So far I've just played with it by ear. But I'm curious if anyone has already worked out tables or a formula to center any one of the BP filters on a particular Hz. frequency. I was kind of annoyed the that doc for the A-127 reprints a table from the Allen Strange book but doesn'
2006-04-24 by Robair, Gino
Thanks for the examples, Ingo. Here's a strange question for you (and Dieter, if has some thoughts about it): how does one determine which bbd (which number of stages) to purchase, without hearing and trying each one? Is it possible to describe the sound and behavior of each bbd
2006-04-24 by davevosh@aol.com
In a message dated 4/24/2006 2:21:26 AM Pacific Standard Time, hardware@doepfer.de writes: you are right. It's the same matter. The rectangle output of the A-111 is AC coupled (capacitor between the rectangle output of the CEM3340 and the socket). This leads to problems with npn
2006-04-24 by m0n075
Hi How can i order some doepfer bbd modules/boards without the bbd ic's. I wanna order several and make them with panels in a other brand format design and different kind of bbd ic's (short ---> long delay). Regards, Dennis
2006-04-24 by Dieter Doepfer
Dave, you are right. It's the same matter. The rectangle output of the A-111 is AC coupled (capacitor between the rectangle output of the CEM3340 and the socket). This leads to problems with npn transistor input stages like the A-117 or the A-113 clock input. There is a simple so