Yahoo Groups archive
Messages
Page 54 of 236 · 11758 messages matched
2012-12-04 by jdchevallier
In my haste to get the psu to the shop to repair two cold solder points I didn t memorize two of the connections. The two connectons are tethered together.
2012-12-04 by Ted Summers
I don t see a fuse on these. If you mean the beige colored surface mount next to CP1 screened on the PCB - that is a capacitor going between the positive and
2012-12-04 by Chase Smith
Thanks, ill try to reseat the chips.
2012-12-03 by Ted Summers
I will check that pin 2 when I get home.... I have no white displays left. I have 5 yellow which were not paid for and no response from the people who reserved
2012-12-03 by Ted Summers
This can happen where the IC s (sometimes specifically the EPROM) becomes unseated. Reseat the IC s on the logic board. While disconnecting the display
2012-12-03 by jdchevallier
Jammie, Right you are. On top of the 400+ dollars I spend on the unit, I ve spend over a day and a half of my own time trouble shooting, I paid to have the 2
2012-12-03 by jammie
is it the light green screen pcb i did give a warning on these the tracks bonding material is rubbish and even with the proper equipment you still can get
2012-12-03 by Chase Smith
Thanks for the help, but I can t find it. There is something right from pin 2 that is unlabeled and has no continuity, but I m not sure if it s a fuse.
2012-12-03 by Ted Summers
I will have to look at one when I get home. I am currently at work. Thx, Ted ... [Non-text portions of this message have been removed]
2012-12-03 by jammie
they are usually 1k1 written on them they are flat squares if you look closely they will have fuse1 written in very small writing pin 2 on the display will go
2012-12-03 by Chase Smith
Power supply is putting out the right voltage. It could have been the 5v. How can I find out which is the fuse on the display? Nothing is labeled as a fuse.
2012-12-03 by Ted Summers
The OLED doesn t use 12V at all. Verify your power supply is outputting the correct voltages, the investigate further like jammie said. There is often some
2012-12-03 by jammie
you cant fry the readers they have internal fuses that blow most are smd types but soldering on a new one will make the work again as for the screen you might
2012-12-03 by Chase Smith
Hi, After frying one cf card reader, I was careful to try to measure the voltages on the new one I was just about to put it. Probe slipped and I shorted the
2012-12-03 by mike stanton
You may be able to get it from the Violator Remaster 5.1 mix. I think some sounds are isolated in those mixes. ________________________________ From: tl200024
2012-12-02 by tl200024
Hello, I am Starting a Depeche Mode cover band. I was wondering if you know where I can find the choir voice for Enjoy the Silence. I own the complete Emax II
2012-12-02 by jammie
yes maybe i have had problems with the light green lcd control panels were the original solding was done to hot and lifted the tracks so that when you put
2012-12-02 by emax_dx5
Consider that postage could has to do with this problem. One of my emax didn t power up as soon as I received it. Contacted the seller and he confirmed that
2012-12-01 by Carl Lofgren
Hey Daniel - nice 80/90s vibe :) /C ... [Non-text portions of this message have been removed]
2012-12-01 by Daniel Baum
Hi all, We don t get much actual music on this list, so I thought I d post my latest track. http://soundcloud.com/daniel-b-1/exercise-in-weird The Emax II
2012-12-01 by BradM
Thanks. Pretty much any place that makes banners should be able to print it for you, Kinko s or any banner shop usually has a vinyl printer/plotter (prints on
2012-12-01 by freddy1771994
Great work. Does anybody know where or how I can print it/have it print?
2012-12-01 by BradM
Thanks Freddy for the help. Reproduction of the SE sticker uploaded to the files section in Emax Stickers folder. I do not guarantee accuracy of color or
2012-12-01 by jammie
solder them pins also check the earth spade tag as this can also come loose and the switching circuit spade tag as this can also come loose i would put a
2012-12-01 by Joel Chevallier
I don t even know what meter your referring to. I m capable of resoldering the two cold joints and reconnecting the psu. Is this that risky? Sigh. I feel like
2012-12-01 by Chase Smith
You should try that, but when you test it, leave the power unplugged from the mainboard. I am not a tech, but my advice to you is to keep the power supply
2012-12-01 by jdchevallier
So I ve just posted two photos/diagrams in the photos sections in a gallery appropriately titled DOA...psu problem . I hope these two photos help illustrate
2012-12-01 by jdchevallier
The loose connections of the part directly next to the fuse in the PSU make me think that there likely was a cold solder point. I decided to open up the emax,
2012-12-01 by jdchevallier
Ted, I sent the photo directly to your gmail since it didn t come through on my response in this thread. Joel
2012-12-01 by Joel-David Chevallier
Ted, So I ve checked the fuse inside the unit on the psu (photo attached.) The fuse seemed fine. That said, the bit of plastic just to the left of the fuse
2012-12-01 by Ted Summers
That is the input block (where the power cable plugs in). Unless there is an issue with the input block itself (mine has an RF filter in it and isn t just
2012-11-30 by Joel Chevallier
The rack is mounted inside an anvil case now so ill need to take it out to inspect a bit further. The two fuses above the power cable connection seem fine. The
2012-11-30 by Joel Chevallier
Ted, I checked the fuses just above the power cable input and they seem to be fine. Forgive my ignorance, but I m not sure what/where the input block is. For
2012-11-30 by jammie
try the fuse in the psu first is it set to the correct voltage on your unit 110 usa 220-240 europe japan cyprus australia theres a switch on the back to change
2012-11-30 by Ted Summers
there are fuses in both the power supply and the input block. did you check all of them? On Nov 30, 2012, at 2:48 PM, jdchevallier wrote: So, after reaching
2012-11-30 by jdchevallier
So, after reaching out on the forums I found an SE HD rack that was sold to me for a completely reasonable price. I was elated when it showed up today, then my
2012-11-29 by freddy1771994
And this one for the SE sticker http://www.synthburgh.com/EMAX%20SE/emu4.JPG
2012-11-29 by freddy1771994
This is what I found at google... maybe you can use it if you re into designing ... http://www.synrise.de/guests/cwernke/bilder/geraete/emax_hd_logo.gif
2012-11-29 by BradM
Anyone have a high rez picture of the HD Retro sticker. Thinking of making a CF Retro sticker based off the original. Will post once done. Also have a
2012-11-29 by BradM
I think this: http://www.alliedelec.com/search/productdetail.aspx?SKU=70080636 may be a drop in replacement for my E-Max II power supply input(marked as KEA
2012-11-28 by jammie
you can get gel pads that change the colur to any colour you like contact noritake itron they might have a distributer in germany ... From: freddy1771994 To:
2012-11-27 by freddy1771994
Hi, My emax I has a VFD diplay, but somehow I don t like the light green colour of it. Is it possible to change the colour of it? I really like light blue
2012-11-27 by Roy Thomas
hello im Roy i have a emu emax l l hd for sell and for $400 if your interested give me a call Roy 562 314 5897 or melechdidymus24@... im in the los angeles
2012-11-27 by Roy Thomas
hello im Roy i have a emu emax l l hd for sell and for $400 if your interested give me a call Roy 562 314 5897 or melechdidymus24@... im in the los angeles
2012-11-27 by Roy Thomas
hello im Roy i have a emu emax l l hd for sell and for $400 if your interested give me a call Roy 562 314 5897 or melechdidymus24@yahoo.com im in the los
2012-11-27 by Krikor Kouchian
Whoo lucky you, all the ones I stumble upon around here were stupidly expensive, but that s France, each time something gets a little rusty they try to sell it
2012-11-27 by jdchevallier
Thanks Brad! There s a certainly an enormous wealth of technical knowledge on this forum that will be an invaluable resource to me going forward. That said,
2012-11-27 by BradM
Great deal!!! And on the off chance there are any issues the group of people on this forum have more info then I ever would have imagined to get it up and
2012-11-27 by jdchevallier
Ted, Thanks for offering the kits and being willing to do the upgrade. Sincerely. That said, last night I stumbled onto an HD keyboard that had just been
2012-11-26 by plus_321
Hi, I am trying to put another oled display in my emax II, but after taking out the old one I hear a whine coming from the screen. I unsoldered the inverter