Re: [emax] Emax Images and OS X
2013-01-05 by Ted Summers
Yes- Wasn t sure how Mac OS X did the raw disk and didn t look before. dd if=EMAX1-1.EZ1 of=/dev/rdisk3 completed in 17 secs. So quite signicant change in
Messages
Browse messages
Page 52 of 236 · 11758 messages matched
Re: [emax] Emax Images and OS X
2013-01-05 by Human Being
When using dd on a Mac, /dev/rdisk* will give you lower-level access and a lot faster transfers.
Emax Images and OS X
2013-01-05 by Ted Summers
I was doing a little testing. I couldn t get EMXP to work using Virtual Box. it would run, and appeared to read an SD CARD ok. But - Writing an image to a SD
Re: Emuser alternative?
2012-12-30 by krikor kouchian
Hi ok it makes sense. i ll ask the company about this external clock signal (i already ask about asynchronous/synchronous). if i get the time to make an emuser
Re: Emuser alternative?
2012-12-30 by esynthesist
I don t think so. The Emu RS422 synchronous protocol requires that the PC (or USB converter) port can accept an external clock signal. I didn t study the
Emuser alternative?
2012-12-30 by krikor kouchian
Hello from reading the tech info (especially the pin section) on this http://www.usconverters.com/downloads/uts_m12_.pdf
Re: [emax] RS422 cable
2012-12-26 by jammie
he is selling mac to emax cables and EII he makes the cables and they are a good length the emulator archives was brought by someone else and they have just
Re: [emax] RS422 cable
2012-12-26 by krikor kouchian
is he selling mac serial cables or RS422 to mac serial cables? the only RS422 to apple serial cablei could find is the printer cable here
Re: [emax] RS422 cable
2012-12-26 by jammie
there is a guy on ebay selling them ... From: krikor kouchian To: emax@yahoogroups.com Sent: Wednesday, December 26, 2012 9:43 AM Subject: Re: [emax] RS422
Re: [emax] RS422 cable
2012-12-26 by krikor kouchian
unfortunately emulatorarchives is down for sometime. i think i have an old mac serial cable. I ll check that first ... -- http://www.krikor.fr +33632199413
Re: [emax] RS422 cable
2012-12-25 by Francis Cote
I can t direct you from where I m replying... Search for emulatorarchives site. You will find it in the emax section. I made one from Minidin 8 serial cable
Re: [emax] RS422 cable
2012-12-25 by krikor kouchian
anyone knows the pinout for the cable? maybe it s easier to make one then! ... old ... -- http://www.krikor.fr +33632199413 bookings: France/Suisse/Benelux:
Re: [emax] RS422 cable
2012-12-25 by Francis Cote
The emax cable s pinout is specific to the emax. ... [Non-text portions of this message have been removed]
RS422 cable
2012-12-25 by krikorola
hello, would this cable work for the Emax/SDemax transfers? http://www.creativevideo.co.uk/index.php?t=product/cable_mac-rs422 i got hold of a mac classic
Re: [emax] Re: PCD-50B alternative
2012-12-22 by Krikor Kouchian
Maybe I can try it and sell it if it does not work, but I have the feeling the bezel is too big from looking at it. http://www.krikor.fr +33632199413 ...
Re: [emax] Re: PCD-50B alternative
2012-12-21 by jammie
they have been given the read and write firmware but as of yet have not been tested with the emax as they are made by the same manufacturer they are 6 slot lun
Re: [emax] Re: PCD-50B alternative
2012-12-21 by Ted Summers
I haven t tested it. That is a recurring question in my mind if one would work or not... but haven t had one.... Thx, Ted ... [Non-text portions of this
Re: [emax] Re: PCD-50B alternative
2012-12-21 by Krikor Kouchian
What about the PCD 60b? Have you ever tested it? http://www.krikor.fr +33632199413 ... [Non-text portions of this message have been removed]
Re: [emax] Re: PCD-50B alternative
2012-12-21 by jammie
32mb max really for a emax1 512mb or 1gb for a emax2 emax 2 has max 100 banks so if you have a 8mb machine then the max hd space used is 800mb if you have a
Re: PCD-50B alternative
2012-12-21 by krikor kouchian
ok thanks that s some good info! if i remember right, CF must be 2G max, right? Le vendredi 21 décembre 2012, jammie a ...
Re: [emax] PCD-50B alternative
2012-12-21 by jammie
not really the whole point in having a cf card with the pcd-50b is its hot swappable so that you can have many cards of library to choose from as there are
Re: [emax] PCD-50B alternative
2012-12-21 by krikor kouchian
as an internal HD, it could be a solution then? 2012/12/21 jammie ... [Non-text portions of this message have been removed]
Re: [emax] PCD-50B alternative
2012-12-21 by jammie
problem is it does not have a casing so it will cost more in the long run getting a case manufactured for it ... From: krikor kouchian To: emax@yahoogroups.com
PCD-50B alternative
2012-12-21 by krikor kouchian
Hi, i was wondering if anyone tried the CF AztecMonster CF-3.5 SCSI adapter? as now it has become cheaper thant the PCD-50B -- http://www.krikor.fr
Re: [emax] Emax 2, bad floppy
2012-12-19 by Ted Summers
Route 66 studios has exact replacement drives.... ... [Non-text portions of this message have been removed]
Re: [emax] Emax 2, bad floppy
2012-12-19 by jammie
its the yamaha drives that the belts turn to goo never heard of an emax drive like that i thought they were direct drives ... From: paulcarlson789 To:
Emax 2, bad floppy
2012-12-19 by paulcarlson789
Hello, I have an Emax 2 with a bad floppy drive. The floppy seems to want to load the disk then sputters out. I have heard a long time ago that the belts
Re: SheepShaver and SDemax
2012-12-19 by krikor kouchian
Yes i understand, but it s getting hard to find old macs around here. Do you know Any apps that would work on OS9? i have a g4 pci with audiomedia3 and dvi, i
Re: [emax] Emax II failing to boot from SCSI device
2012-12-19 by jammie
scsi to ide adapters have a delay this sometimes causes a problem on the asr10 it searches for scsi and it asks for floppy then goes to ask floppy again then
Re: [emax] Emax II failing to boot from SCSI device
2012-12-19 by Ted Summers
OK- so I came home and did a little testing. I have an IDE to PC Card drive in my Emax 2. I have the ACARD 7720U to connect it to the SCSI. Now, what I find is
Re: [emax] Emax II failing to boot from SCSI device
2012-12-19 by Francis Cote
Sounds risky. ... [Non-text portions of this message have been removed]
Re: [emax] Emax II failing to boot from SCSI device
2012-12-19 by Ted Summers
I don t believe they are socketed. you have to desolder the EEPROM and then you could copy the content. Otherwise, you lose the info that you have how much
Re: [emax] Emax II failing to boot from SCSI device
2012-12-19 by Francis Cote
Yes please Ted? Isn t it just a mater or copying the content to another eeprom chip? ... [Non-text portions of this message have been removed]
Re: [emax] Emax II failing to boot from SCSI device
2012-12-18 by Simon Forsyth
Happily.. any thoughts Ted?.. S. ________________________________ From: jammie To: emax@yahoogroups.com Sent: Tuesday, 18
Re: [emax] Re: SheepShaver and SDemax
2012-12-18 by Ted Summers
this is my opinion ... [Non-text portions of this message have been removed]
Re: [emax] Re: SheepShaver and SDemax
2012-12-18 by Ted Summers
and what device has the proper RS422?- oh - hello my old macintosh friend / computer (warm fuzzy thoughts).... ... Is much less trouble to get a real machine
Re: SheepShaver and SDemax
2012-12-18 by esynthesist
I haven t tried this, but even if the SD for Emax would start/run, it requires a synchronous RS422 serial communication with the Emax to be really useful. In
Re: [emax] Emax II failing to boot from SCSI device
2012-12-18 by jammie
ask ted but i thought it would only boot from scsi id 1 never owned an emax 2 as i had an EIII ... From: Francis Cote To:
Re: [emax] Re: Emax II failing to boot from SCSI device
2012-12-18 by Francis Cote
My scsi zip is using 5 or 6, with same known problem. Anybody knows if it s possible replace the eeprom or not. ... [Non-text portions of this message have
Re: [emax] Re: Emax II failing to boot from SCSI device
2012-12-18 by Simon Forsyth
The drive works fine on ID7 loads banks and saves without issue. I have changed the jumpers to switch it to ID1 and still get the same problem the Emax is
Re: Emax II failing to boot from SCSI device
2012-12-18 by dwv1957
You cannot use ID7, 7 is the address of the scsi controller, set it to something between 1 and 6 and it should be fine (0 is the floppy) Dave ... I have the
Re: [emax] Emax II failing to boot from SCSI device
2012-12-18 by Francis Cote
I have the same annoying issue. Is this EEPROM replaceable? ... [Non-text portions of this message have been removed]
Emax II failing to boot from SCSI device
2012-12-18 by Simon
Hi Guys.. I posted this up a while ago, but am looking for a solution here The Emax boots from floppy, but when I try to assign it to boot from an internal
Re: [emax] Molex cable for scsi device
2012-12-18 by Ted Summers
http://www.performance-pcs.com/catalog/index.php?main_page=product_info&cPath=82&products_id=21381 Then get a normal y cable splitter that is available. ...
Re: [emax] Molex cable for scsi device
2012-12-18 by jammie
you can create an new cable with the original connector but you need an amp push down tool and other end you need some new floppy mini molex crimps and some
Re: [emax] Molex cable for scsi device
2012-12-18 by krikor kouchian
yes Jammie i can imagine you knew that already! my answer was to Al, on my side i was thinking of recycling the original connector on pcb digital board side so
Re: [emax] Molex cable for scsi device
2012-12-18 by jammie
the cables i use are correct as i use them not just foor emax but for all the sampler makes ensoniq yamaha akai emu roland korg ... From: krikor kouchian To:
Re: [emax] Re: Molex cable for scsi device
2012-12-18 by jammie
ok i can supply them but i need to know where you live as postage will be accordingly you will still need a extender cable with a female molex hd and a male
SheepShaver and SDemax
2012-12-18 by krikor kouchian
Hello i was wondering if anyone tried SDemax in Sheepshaver? best K -- http://www.krikor.fr +33632199413 bookings: France/Suisse/Benelux: fanyktdj@gmail.com
Re: [emax] Molex cable for scsi device
2012-12-18 by krikor kouchian
be careful as the connectors are not the same pinout! 1 on floppy/berg is +5V but 1 on scsi/molex is +12V http://en.wikipedia.org/wiki/Molex_connector