using SDS with Awave
2011-04-13 by James Ulibarri
I am a big fan of using Awave doing SDS dumps to the SP1200 with a little Emu 2x2 midi interface and it works like a champ, finally after about 2 years of
Messages
Browse messages
Page 91 of 236 · 11758 messages matched
Re: EMUSER and Emax I
2011-04-13 by esynthesist
I m not 100 pct sure what the exact situation is with your XCK1 pin, but the EmuSer s firmware WILL put the clock in SYNC mode once EMXP instructs it to do
Re: EMUSER and Emax I
2011-04-13 by esynthesist
Pfff... - unless you have luck, and can get in touch with the author. Unfortunately i could not True, you have sent two e-mails to me, but both have been
Re: EMUSER and Emax I
2011-04-13 by Adam
OK guys, i do NOT recommend anyone to build EMUSER. We spent over 15 hours to get this thing work, and there are problems with the hex files as far as i can
EMUSER and Emax I
2011-04-12 by Adam
We ve tried to build the EMUSER around the Teensy++ board, and we had no success so far. It seems like that upon bank transfer, the clock disappears on the
Re: Parting out: Emax revision 3.3!!!
2011-04-05 by Adam
Im interested in this, wrote email, but no reply. is it still available?
Parting out: Emax revision 3.3!!!
2011-04-04 by mlivingston8
I m SICK AND TIRED of this display shit!!! I m too slow to get a display working so, I m parting out this machine. It s an Emax I with all boards know
Re: [emax] Re: LCD replacement from RS
2011-03-30 by jammie
read the pdf of your lcd manufacturer it will tell you what size resistor to useits just a back up to prevent the over current as for the pot i used a 10k
Re: [emax] Re: LCD replacement from RS
2011-03-30 by jammie
yes to much current burns the led to bright and it can burn it out quicker than an el panel ... From: Ted Summers To:
Re: LCD replacement from RS
2011-03-30 by mlivingston8
Ok, so for the novice people (me) I assume this resistor is pretty common and I can get it from radio shack. What resistor do I need to buy here? Hell, if
Re: [emax] Re: LCD replacement from RS
2011-03-30 by jammie
thats right current limiting resistor for the led back light manufacturers recommendation for there display cut the track to the a pin correct this comes from
Re: [emax] Re: LCD replacement from RS
2011-03-30 by Ted Summers
My understanding is that you are putting a resistor in line with 5v wherever you get that from to reduce it a little to decrease the brightness. I didn t have
Re: LCD replacement from RS
2011-03-30 by mlivingston8
Yeah, I think that makes sense to me now. I ll have to take the emax LED board out and look at the traces again but I do think I remember that pin A was the
Re: LCD replacement from RS
2011-03-30 by mlivingston8
I m located in Atlanta. Yeah, I did everything in those steps but put in pin A thinking that it was to supply the voltage to that trace on the LED board.
Re: [emax] Need your help with E-MU Classic Keys
2011-03-29 by Ted Summers
From google:
Re: [emax] Re: LCD replacement from RS
2011-03-29 by Ted Summers
Pin A and K are the anode and cathode of the backlight. The original EL backlight on Emax is not +5V. To use an LED backlight, you break the connection of the
Emax Display Replacement (KYBD Version) macdougall.jason
2011-03-29 by Vavasseur Philippe
Hello you post pictures on the screen, you can give more information about how to follow the reference resistor LCD or purchase transformer website? Thank you
Re: [emax] Need your help with E-MU Classic Keys
2011-03-29 by Jason Mc
I do not know anything about the E-MU classic Keys display. Sorry I cant help out. ... [Non-text portions of this message have been removed]
Re: [emax] Re: LCD replacement from RS
2011-03-29 by Jason Mc
The one thing I have learned about electronics is patients and attention to details. I hope i can help you out. I m not a professional, I do these repairs as a
Re: LCD replacement from RS
2011-03-29 by mlivingston8
Call me stupid but I still don t get this procedure. One person says add a potentiometer, the other says there is no need to. Nothing is working for me
Re: LCD replacement from RS
2011-03-29 by mlivingston8
Call me stupid but I still don t get this procedure. One person says add a resistor, the other says there is no need to. Nothing is working for me still.
Re: Need your help with E-MU Classic Keys
2011-03-29 by Yoshiaki
Hi, Freddy, You can get it at EPR electronics (http://www.eprelectronics.com). You will find Parts Store of E-mu Classic Keys(Model 9027). Peace!! Yoshi
Need your help with E-MU Classic Keys
2011-03-29 by hannsg.logitech
Hello, I know that this is the wrong place for asking things about the E-MU Classic Keys, but I have an urgent problem: I just can t find a spare display for
Re: [emax] Re: LCD replacement from RS
2011-03-27 by Jason Mc
Hello All, Have a look at http://groups.yahoo.com/group/emax/photos/album I just posted pictures of the steps I took replacing my Emax Display. I hope this
Re: LCD replacement from RS
2011-03-27 by mlivingston8
Yeah, I soldered in the resistor to the other jumper on the board. Pin A I thought was implied because just moving that resistor still doesn t hook it up to
Re: LCD replacement from RS
2011-03-27 by dutchbeats
he said to solder 1 - 14 and pin k which is the led ground. don t solder the led + because you already are getting power for the screen by switching the
Re: [emax] Re: LCD replacement from RS
2011-03-27 by Ted Summers
yes- still got the panel but its emax 2 keyboard..... still have an emax2 audio board also... thx, Ted PS- I didn t want to mess with the possibility of the
Re: [emax] Re: LCD replacement from RS
2011-03-27 by jammie
see told you ted was the man if he fitted an led light version it would just burn out the led so in effect would need a new led back light if he is going to
Re: [emax] Re: LCD replacement from RS
2011-03-26 by Ted Summers
If the Emax can t communicate properly with the display it will hang. I replaced mine with direct Replacement EL backlght. So I didn t have to modify the power
Re: LCD replacement from RS
2011-03-26 by mlivingston8
I m located in the states, Atlanta GA, if anyone is willing to fix my LED board.
Re: LCD replacement from RS
2011-03-26 by mlivingston8
It s just that for a novice like me, though good at soldering, I have to rely on the info that was posted here which is a little disjointed. There s no other
Re: [emax] Re: LCD replacement from RS
2011-03-26 by jammie
fit a led display as it will blow if you connected it to the ac supply also as i said you need to disconent pin 3 by cutting the trac and connecting a pot
Re: LCD replacement from RS
2011-03-26 by mlivingston8
Great... my emax doesn t work anymore after trying this replacement screen. It will turn on, the screen turns on but it doesn t display characters and the
Re: LCD replacement from RS
2011-03-25 by mlivingston8
I ve replaced the header pins 1-14 to the new display but I m confused on where to solder the A and K pins on the new display. I see the ground and +5 on the
Re: EMXP and emax HD OS 1.1
2011-03-25 by Matthieu Roche
Oh, thanks a lot :) That would be a great mod, if it is possible to implement it. EMXP is a great piece of software, very helpful when you have an Emax :)
Re: EMXP and emax HD OS 1.1
2011-03-20 by esynthesist
I will check if I can change this in EMXP, and if it is possible to add support for the OS HD and OS SE HD on removable media. To be honest I didn t even
Re: EMXP and emax HD OS 1.1
2011-03-17 by Matthieu Roche
That is the procedure I suspected. Thanks a lot! :) I will give it a try. I am still interested in other possibilities. :)
Re: [emax] EMXP and emax HD OS 1.1
2011-03-17 by Jason Mc
When I updated my Emax to the cf drive, I needed to keep a floppy drive installed. After I booted the floppy with the HD OS, I then formatted and transferred
EMXP and emax HD OS 1.1
2011-03-17 by Matthieu Roche
Hi all, I own an Emax HD, and I just installed the card reader, following Ted Summers instructions. The problem is that the Emax runs the HD OS 1.1 (not SE).
Re: LCD replacement from RS
2011-03-16 by dutchbeats
many thanks!
Re: [emax] Re: EMAX SE FLOPPY REPLACEMENT
2011-03-16 by Ted Summers
No idea- you have to have a floppy that can be set to Drive Select 0. Newer floppies don t have the jumpers necessary to set that way. You can get exact
Re: EMAX SE FLOPPY REPLACEMENT
2011-03-16 by elektro_7
I have an atari 1040st you know if this floppy can work on the emax??
Re: [emax] Re: EMAX SE FLOPPY REPLACEMENT
2011-03-16 by jammie
if ted does not have them i have some that i brought from ted ... From: Ted Summers To: Sent: Wednesday, March 16,
Re: [emax] Re: EMAX SE FLOPPY REPLACEMENT
2011-03-16 by jammie
ted is the man and the slim floppy you can by from ebay ted will tell you the best models to buy or go for the floppy emulator ... From: elektro_7 To:
Re: [emax] Re: EMAX SE FLOPPY REPLACEMENT
2011-03-16 by Ted Summers
I don t have a stock of these anymore and as they aren t selling with any regularity I have no immediate plans to re-stock. Regards, Ted ... [Non-text portions
Re: EMAX SE FLOPPY REPLACEMENT
2011-03-16 by elektro_7
thanks and how can i order the slim converter, and from where can i order it? thanks again
Re: [emax] Re: LCD replacement from RS
2011-03-16 by jammie
on the rack you would still need the pot as the angle on the rack is a negitive veiw angle voltage ... From: Jason Mc To: emax@yahoogroups.com Sent: Wednesday,
Re: [emax] EMAX SE FLOPPY REPLACEMENT
2011-03-16 by jammie
get a slim floppy converter from ted and use a slim floppy it works great ... From: elektro_7 To: emax@yahoogroups.com Sent: Wednesday, March 16, 2011 3:45 AM
EMAX SE FLOPPY REPLACEMENT
2011-03-16 by elektro_7
Can someone help me on wich floppy i need for my emax se,, i try to change it with a Nec FD1231h and a sony mpf920 but didnt work,, any help thank u all
Re: LCD replacement from RS
2011-03-16 by Jason Mc
Sorry about the last post gave the wrong part number, this is exact part I used. I have recently replaced my el foil display with this one: Mouser Part #: