Re: [gsp-2101] Re: Stability issues
2008-10-30 by krazydog
Did you try a new battery by chance? Sean ... From: Nestor To: gsp-2101@yahoogroups.com Sent: Thursday, October 30, 2008 5:37 PM Subject: [gsp-2101] Re:
Messages
Browse messages
Page 12 of 45 · 2224 messages matched
Re: Stability issues
2008-10-30 by Nestor
Hello again, I replaced the regulators with no luck, with the new trio the unit behaves exactly the same. I think it must be a bad contact somewhere near the
Re: Stability issues
2008-10-26 by Nestor
Today the unit locked up, auto rebooted and then the midi assignments were corrupted. I ll replace the voltage regulators this week. Thanks for the advice
RE: [gsp-2101] Re: Stability issues
2008-10-25 by Glenn Warner 3rd
My bad, yes I have only a single sdisc. I put a pair of high gain JJ tubes in my 2101 and it sounds great for a preamp. The quality of my TC g-major effects
RE: [gsp-2101] Re: Stability issues
2008-10-25 by M M
PPC stands for parallel processing card. You can only have one PPC in your 2101. If you have no PPC then you only have one SDISC processor. Soaking up the
RE: [gsp-2101] Re: Stability issues
2008-10-25 by Glenn Warner 3rd
Hi Graham, Can you point me to a copy of the software? I have version 2.0 and only one PPC in my 2101 unit. Can you also tell me the best way to determine the
Re: [gsp-2101] Re: Stability issues
2008-10-25 by krazydog
Nester if you have similar issues again, it could be your voltage regulators. They tend to go after awhile. They went on mine & I experienced the same problems
Re: [gsp-2101] Re: Stability issues
2008-10-25 by Graham Pearson
Nestor: EPROM Version 3.00.00 is stable whether or not the PPC-210 is installed. The only possible issue is when owners upgrade to version 3.00.00 and forget
Software
2008-10-25 by Nestor
Hello, after upgrading my GSP-2101 with the PPC-210 board, I realized that there is no much PC software to create new algorithms or presets. Also, the existing
Re: Stability issues
2008-10-25 by Nestor
Hello again, after upgrading the unit with a PPC-210 (bought from second hand market , but it s a Dieter card) the issues seem to be corrected. Perhaps the
My list of Yahoo Groups
2008-09-27 by andy wilkes
Hi, You can see a list of my groups on Grouply at the link below. Maybe you ll find some you want to join. andy Here s the link:
RE: [gsp-2101] I wanna get to know you! - spam
2008-08-29 by Glenn Warner 3rd
get em graham!Glenn To: gsp-2101@yahoogroups.comFrom: matchbjffriends@yahoo.comDate: Fri, 29 Aug 2008 02:00:12 +0000Subject: [gsp-2101] I wanna get to know
Re: Control One Pedal problem
2008-08-13 by woboguitarelectronics
Thanks a lot Dieter! Cheers, Filip ... instability. ... the pedal. ... problem or ... need to ... it again.
Re: [gsp-2101] Control One Pedal problem
2008-08-13 by Dieter Waechter
I forgot: check the 5V supply (at voltage regulator) inside the C1 for voltage instability. Dieter ... From: Dieter Waechter To: gsp-2101@yahoogroups.com Sent:
Re: [gsp-2101] Control One Pedal problem
2008-08-13 by Dieter Waechter
Hi! a) replace the LED on the small PCB on the metal sheet monted on the pedal. b) check the wires to the LED c) check if it happens if you shake or drop the
Control One Pedal problem
2008-08-13 by woboguitarelectronics
Hello, I have posted this problem back on July 29th, but no one have answered, so I thought no one get my message and decided to post it again. I ve got a
RE: [gsp-2101] Control One died
2008-08-12 by Glenn Warner 3rd
You can purchase any midi controller, it will work. I use the GCX Ground Control Pro, EXCELLENT midi controler with led s and a display. Works great for my
RE: [gsp-2101] Control One died
2008-08-12 by M M
I ll go with my favorite advice which has fixed quite a few things for me in the past. Gently press down and reseat all the chips and ribbon cables/connectors
Control One died
2008-08-12 by Jey
Hi everyone. I ve had my 2101 with the PPC-210 upgrade for almost 13 years now with no problems. That is until last month when I accidently injected a dose of
Re: [gsp-2101] The problem Digitech GSP 2101
2008-08-03 by Dieter Waechter
Hi! Yes! You can upgrade to 3.00.00.a (The latest Artist Version) You also can upgrade with the PPC210. You ll find the details here:
RE: [gsp-2101] The problem Digitech GSP 2101
2008-08-03 by Glenn Warner 3rd
Thanks Dieter, I was only guessing. You re also right about the groove tube lots can be different. But I have to stick to my guns on the tubes, I have used
Re: [gsp-2101] The problem Digitech GSP 2101
2008-08-03 by Dieter Waechter
Glenn, Groove Tubes (12AX7A) are chinese made Chuguang tubes (and other cheap tubes) with Groove Tubes branding since some time. The chinese tubes work well
RE: [gsp-2101] The problem Digitech GSP 2101
2008-08-03 by Glenn Warner 3rd
I was going to say at that age of a 2101, did you check the tubes? If you go with new tubes, stay away from cheap crappy chinese tubes like groove tubes, and
RE: [gsp-2101] The problem Digitech GSP 2101
2008-08-03 by M M
Is it the volume knob/pot? Try spraying some deoxit or contact cleaner in the pot and/or input jack. Soaking up the cathode rays To:
The problem Digitech GSP 2101
2008-08-03 by gil bert
Hi, I have an Digitech GSP 2101. The level of sound is not stable, it is low after a few minutes, it then becomes normal and is weak again. I cannot any
Re: control pedal
2008-07-29 by woboguitarelectronics
Hello, I ve got some other problem with my C1 controller. When I use the footswitch for activating particular preset then the unit remembers the state of the
Re: [gsp-2101] control pedal
2008-07-29 by goddardfil@gmail.com
I sent this post almost week ago, but no one has answered, so I thought it might not went through... Here is the copy of my message: Hello, I ve got some other
RE: [gsp-2101] Stability issues
2008-07-29 by M M
I suggest replacing the battery and performing a hard reset if you have not done so already. I had a TSR24-S (2101 minus the preamp) that was doing what you
Re: [gsp-2101] Stability issues
2008-07-29 by Graham Pearson
Hello Nestor: Nobody can be sure exactly what is wrong with your unit. So try some easy and inexpensive fixes first: A. Perform a factory reset. 1.. Power off
Stability issues
2008-07-29 by Nestor
Hello group, this is my first post since I joined the community. First of all, I must excuse about my English because is not my mother language (I m from
Re: [gsp-2101] control pedal
2008-07-24 by chingway
Thanks Graham I ll give it a shot On Wed, Jul 23, 2008 at 6:52 PM, Graham Pearson
Re: [gsp-2101] control pedal
2008-07-23 by goddardfil@gmail.com
Hello, I ve got some other problem with my C1 controller. When I use the footswitch for activating particular preset then the unit remembers the state of the
Re: [gsp-2101] control pedal
2008-07-23 by Graham Pearson
Tom: There are 2 steps to using an expression pedal to control a program parameter. You have performed only one step - pedal calibration. The other step is
Re: [gsp-2101] control pedal
2008-07-23 by chingway
I think so I mean I calibrated it according to the manual On Tue, Jul 22, 2008 at 9:32 PM, Graham Pearson
Re: [gsp-2101] control pedal
2008-07-23 by Graham Pearson
Tom: Are you linking your pedal to the appropriate wah and pedal steel parameters, using the CC menu? ... From: earldoink To: gsp-2101@yahoogroups.com Sent:
control pedal
2008-07-23 by earldoink
I m having a problem with my expression pedal it lets me calibrate but doesn t work with the wa or the pedal steel settings I ve done the resets and still no
Re: PPC-210
2008-07-16 by David
Hi Hari, Actually, I haven t tried lining the insides of my guitars. I did try placing sheets of aluminum foil between my body and the guitars to no avail.
Re: [gsp-2101] Re: my intro
2008-07-15 by Hari Floura
David I know this is silly, but I couldn t resist http://www.thinkgeek.com/tshirts/generic/9080/ Regards Hari ... From: David Reeves-Brown
Re: [gsp-2101] Re: PPC-210
2008-07-15 by Hari Floura
David I am assuming that you have already have shielding in your guitars (cavity & covers lined with copper or metal foil and connected to ground) and you
Re: PPC-210
2008-07-10 by Dave Kane
I can Also attest to Deiter s PPC cards, I am running a 2101 with an origional Digi card and in tandem I use a TSR-24s with one of his cards in it, The PPC-200
Re: [gsp-2101] Re: PPC-210
2008-07-09 by Kevin Owens
David. He is the authourity. I am a happy customer of his and I highly recomend him. I have a Limited Addition (Purple Haze) and provided me with the 3.000a
Re: PPC-210
2008-07-09 by David Reeves-Brown
Thanks Dieter, I just bought it. And thanks for the encouragement all. I had searched the group and found the earlier (2007) posts regarding Dieters
RE: [gsp-2101] PPC-210
2008-07-09 by M M
Yes and his website has loads of handy info. I just used it to find how to reset my corrupted TSR24-S (which booted up and started working again after that and
RE: [gsp-2101] PPC-210
2008-07-09 by Glenn Warner 3rd
Yes, take that link! Dieter is the authority on getting your GSP2101 up to par. He has all the upgrades you need with complete instructions and is very easy!
Re: [gsp-2101] PPC-210
2008-07-09 by Dieter Waechter
... Yes. here: http://search.ebay.com/_W0QQsassZchronotronix Dieter
PPC-210
2008-07-08 by David
Hi All, Is the PPC-210 still available anywhere? Does installing the board require any soldering or is it pretty straight forward, plugin then move a jumper
Re: my intro
2008-07-08 by David Reeves-Brown
Thanks to all of you for making me feel welcome! Sorry it took me so long to get back to you. I m not sure what you re having trouble with on the N. Gates,
RE: [gsp-2101] need some help getting the wah to sound right it tracks funny and ....
2008-07-08 by Glenn Warner 3rd
Hi Joe, Do you have dual s-disc processors and the 3.0 upgrade in your gsp 2101? I know the 3.0 upgrade and extra s-disc helps smooth out some of the wah and
need some help getting the wah to sound right it tracks funny and ....
2008-07-08 by joeroth1964
The sweep seems to be shallow it one of the patches better than others to start with before I begin to edit? I actually need to make a few different patches,
RE: [gsp-2101] Intro
2008-07-02 by M M
I took my 2101 over to a buddy s house for a quick jam the other day, plugged it into his PA w/ the xlr s. After a while he asked how much they cost. It