Yahoo Groups archive
Messages
Page 121 of 564 · 28179 messages matched
2011-02-12 by Sidney
I wouldn't be playing polyphonic because the ADSR envelope would not be activated each time I touch a different note? Or maybe a new module similar to the A-143-2, with four inputs but only four knobs giving each voice the same envelope? Do you think that the A-190-5 Interface wi
2011-02-12 by Monroe Eskew
The most direct way would be to control them from a common signal. Use a multiple to split the gate or filter modulation source. However, if you want to attack several notes independently, like how one plays a piano, then you need one VCA and envelope for each VCO. If you don't d
2011-02-11 by Florian Anwander
Hi Sidney > In fact I was looking for something similar to what Florian explained, working like a Korg Mono-Poly, because I could use the filters, VCA and ADSR modules from my system, just needing to add more oscillators in order to achieve a polyphonic system. It is not only the
2011-02-11 by Monroe Eskew
If you want to control the volume of each note independently you need one VCA and one ADSR for each voice. You can get away with one filter at the end, but usually there is a filter in each voice. I would recommend 4 A111-5 modules. That's all you need. Monroe On Fri, Feb 11, 201
2011-02-11 by Sidney
Hi Monroe. In fact I was looking for something similar to what Florian explained, working like a Korg Mono-Poly, because I could use the filters, VCA and ADSR modules from my system, just needing to add more oscillators in order to achieve a polyphonic system. Anyway, both ways e
2011-02-11 by Florian Anwander
Hi Sidney > Hello. I am very interested about the possibilities of the A-190-5 Polyphonic Midi-to-CV/Gate Interface. Does anybody knows if four oscillators controlled by one Midi channel, could be connected to a A-138 B mixer module and this output connected to a single filter an
2011-02-11 by Sidney
Hello. I am very interested about the possibilities of the A-190-5 Polyphonic Midi-to-CV/Gate Interface. Does anybody knows if four oscillators controlled by one Midi channel, could be connected to a A-138 B mixer module and this output connected to a single filter and ADSR envel
2011-02-10 by Justin Owen
Hi Matt, I don't own an A-154 - but here's how I do it: Clock (Squarewave out of Bubblesound uLFO) > One half of A-180 Multiple A-180 Out 1(1) > Clock In of A-155 A-180 Out 2(1) > Trig. In of A-160 A-160 /16 Out (the manual says /8) > Other half of A-180 Multiple A-180 Out 1(2) >
2011-02-10 by yahoo@doepfer.de
> Dieter, the explanation on page 11 (and fig.2) of the A-154 manual > refers to the use of two A-155 modules. What I want to do is run a 16 > step sequence from one A-155 module. > > On page 11 it's written: "it is possible to generate sequences of up to > 16 steps too if two tr
2011-02-10 by Florian Anwander
Hi Matt A154 9-16/A3 out -> A150 CV-In A155 CV-Out upper row -> A150 I/O In 1 A155 CV-Out lower row -> A150 I/O In 2 A150 O/I is the final CV-out if you want the two trigger rows the same way you have to split the cable from A154 9-16/A3 out and feed it to the second switch in th
2011-02-10 by mfretton
Dieter, the explanation on page 11 (and fig.2) of the A-154 manual refers to the use of two A-155 modules. What I want to do is run a 16 step sequence from one A-155 module. On page 11 it's written: "it is possible to generate sequences of up to 16 steps too if two trigger rows r
2011-02-09 by Richard Scott
I have found the DIY #2 is not very good if you have VCOs (especially multiple VCOs) in that rack, for sequencers and most other modules I've found it to be absolutely fine richard On 2/9/11 11:12 AM, phono 1337 wrote: > I just ordered one to power a small 3u rack i have here and
2011-02-09 by phono 1337
I just ordered one to power a small 3u rack i have here and it was only after ordering that i noticed the comments about the power instability. Is it really that bad? just wondering if I should return it and get the #1 kit Paul [Non-text portions of this message have been removed
2011-02-09 by yahoo@doepfer.de
> In the A-154 manual it's stated that an A-150 can be used with an > A-154/155 to switch between the two CV rows of the A-155 thus allowing > 16 step sequences from a single A-155, but it isn't explained how this > is done. Can anyone explain the process/patch to me? Thanks, Mat
2011-02-08 by Matt
In the A-154 manual it's stated that an A-150 can be used with an A-154/155 to switch between the two CV rows of the A-155 thus allowing 16 step sequences from a single A-155, but it isn't explained how this is done. Can anyone explain the process/patch to me? Thanks, Matt
2011-02-08 by abstractjuz
Hello, More of my Doepfer Modules and a G6 Rack available for sale on eBay: A-110 Voltage Controlled Oscillator (VCO): http://bit.ly/dNzP73 A-116 Voltage Controlled Waveform Processor: http://bit.ly/g5GZQU A-130 Linear Voltage Controlled Amplifier (VCA): http://bit.ly/i3Rplu A-13
2011-02-07 by Florian Anwander
Hi Sidney To my experience the 2N3904 can be used as replacement for the BC547C. The 2N3904 has to placed the other way around (flat side of the 2N3904 should point in the direction where the round side of the BC547C is looking at). See http://www.datasheetcatalog.org/datasheet/S
2011-02-07 by yahoo@doepfer.de
> i love the control of the 154, specifically the VC last step, but > don't really need the 155. I'd just like to control the 152 > addressable switch with it. I can get a lot of good stuff when using > the CV in of the 152, along with pre-processing, but when using clock > in, I
2011-02-07 by yahoo@doepfer.de
> I think I had plugged the A190-2 the wrong way the first time I > plugged it into the power bus board, and might damaged the unit. > It seemed to be working fine, as it was receiving midi messages > and activating the A110 both from the CV1 and pitch bend from > CV2. But the ga
2011-02-07 by Sidney
I will try to find the transistor here in Brasil and see if that solves the gate output problem. If I won't find I will send to the dealer. Thank you, Sidney --- In Doepfer_a100@yahoogroups.com, wrote: > > > I think I had plugged the A190-2 the wrong way the first time I > > plug
2011-02-07 by Sidney
Yes, the gate's LED lights up when I press a key and go off when the key is released, but doesn't activate the envelope generator. --- In Doepfer_a100@yahoogroups.com, Florian Anwander wrote: > > Hello > > ok, then the gate out does not provide a gate voltage. Does the LED > ligh
2011-02-07 by Monroe Eskew
Nevermind... I found a detailed datasheet on the chip. The VCO should respond to voltages that will sweep it x octaves, 10 wrote: > Hello, > > I am wondering about the CV tracking range of the dark energy. I was just > about to buy one but want to make sure it's right for me. I r
2011-02-06 by dancemachine
i love the control of the 154, specifically the VC last step, but don't really need the 155. I'd just like to control the 152 addressable switch with it. I can get a lot of good stuff when using the CV in of the 152, along with pre-processing, but when using clock in, I can't see
2011-02-06 by Monroe Eskew
Hello, I am wondering about the CV tracking range of the dark energy. I was just about to buy one but want to make sure it's right for me. I read a description of the CEM3394 and it said that the VCO accepts +/- 4V. I'm sure the input is divided by some factor before being fed in
2011-02-06 by Florian Anwander
Hello ok, then the gate out does not provide a gate voltage. Does the LED light up when you press a key (and go off if you release the key)? If yes, then the gate out of the intereface is broken in fact. Florian Sidney wrote: > Hi Florian. > > I did what you told but I only got t
2011-02-05 by eyesaw
UPDATE FS: a112 Sampler/Wvtbl - $210, a100 psu-1 (650 ma) - new $50, a199 Belton Spring Tanks (2) - new @ $10 Harvestman Tyme Sefari - in box $249 All are in excellent condition. Modules w/screws & ribbon. U.S. only - post & ins. additional - check or M.O. preferred Thanks - Bill
2011-02-05 by Sidney
Hi Florian. I did what you told but I only got the same sound/note with no pitch variation when pressing any key from the keyboard. --- In Doepfer_a100@yahoogroups.com, Florian Anwander wrote: > > Hi Sidney > > > I tested the LFO sending a square wave to the A140 and noticed that
2011-02-05 by Sidney
Hi Florian. I am adjusting the trim pots of the VCO, but altough I am still trying to get an exact tonal scale, it's getting closer to that. Is there a trim adjust on the D/A converter from the A190-2 midi interface module? --- In Doepfer_a100@yahoogroups.com, Florian Anwander wr
2011-02-05 by Florian Anwander
Hi Sidney > I tested the LFO sending a square wave to the A140 and noticed that it responded. The A190-2 seems that is maybe faulty because it's not sending the gate to any module. Maybe it's my fault. ok, now tune the VCO extremely low and then insert the Gate-Out from the A190-
2011-02-05 by Sidney
Hi York. The trimming problem seems to be getting solved. I am finding a little difficult to tune exactly since there are few trimming potentiometer to be adjusted. But seems I am getting closer to a conventional tonal scale as I compare to the piano sound from my digital worstat
2011-02-04 by York Luethje
Hi Sidney, Unfortunately I am not directly familiar with the A-190-2. In the manual there is a diagram of the circuit board where a trim pot for the CV scale is indicated. Trimming this might solve your tuning issue. As for the missing gate I am at a loss tbh. It's quite possible
2011-02-04 by Sidney
Hi Florian. Yes I connected CV Note from A-190-2 to A110 CV1. I think I had plugged the A190-2 the wrong way the first time I plugged it into the power bus board, and might damaged the unit. It seemed to be working fine, as it was receiving midi messages and activating the A110 b
2011-02-04 by Sidney
Hi York. I think I had plugged the A190-2 the wrong way and might damaged the unit. It seemed to be working fine, receiving midi messages and activating the A110 both from the CV1 and pitch bend from CV2. But the gate output problem indicated there is something wrong really. Than
2011-02-04 by Florian Anwander
Hi Sidney > I also notice that the VCO doesn't make a tonal scale sound as I press notes from the keyboard. For example, if I press a C3 then a C4 on the keyboard I hear another interval instead of an octave. I kept the system turned on for more than 20 minutes as I read it needs
2011-02-04 by Sidney
Hello York. I am connecting my midi keyboard with a standard midi cable to the midi input from A190-2 interface. I also notice that the VCO doesn't make a tonal scale sound as I press notes from the keyboard. For example, if I press a C3 then a C4 on the keyboard I hear another i
2011-02-04 by Sidney
Hello Florian. Yes, the Gate LED lights up when I send a midi message from the keyboard. All the waveforms from the LFO trigger the gate of A140. Sidney --- In Doepfer_a100@yahoogroups.com, Florian Anwander wrote: > > Hello Sidney, > > The rectangle out of the LFO does trigger th
2011-02-04 by Florian Anwander
Hello Sidney, The rectangle out of the LFO does trigger the Gate of the ADSR. Does the Gate LED at the A190-2 light up if you press a key on your midi keyboard? Florian
2011-02-04 by York Luethje
Hi Sydney, how are you adressing the Midi interface? _____ Von: Doepfer_a100@yahoogroups.com [mailto:Doepfer_a100@yahoogroups.com] Im Auftrag von Sidney Gesendet: Freitag, 4. Februar 2011 12:36 An: doepfer_a100@yahoogroups.com Betreff: [Doepfer_a100] Can't trigger A-140 from A-19
2011-02-04 by phono 1337
thanks guys On 4 February 2011 15:25, Florian Anwander wrote: > Os schrieb: > > http://www.doepfer.de/a100p_e.htm > > to specify a bit more: > "suitcase is available in two versions: > Version 1: In this version the mains inlet is located at the front > ... > Version 2: In this v
2011-02-04 by Sidney
Hello everybody. I'm a totally newbie and just assembled my A-100 mini system this week. It has a A-190-2, A-110, A-106-1, A-145, A-132-3 and A-140 assembled on a Tiptop Happy ending kit. I tried to send a gate output from the A-190-2 midi interface to the A-140 ADSR gate input b
2011-02-04 by Florian Anwander
Os schrieb: > http://www.doepfer.de/a100p_e.htm to specify a bit more: "suitcase is available in two versions: Version 1: In this version the mains inlet is located at the front ... Version 2: In this version the mains inlet is located at the rear panel ..." I am not sure whether
2011-02-04 by Os
http://www.doepfer.de/a100p_e.htm os. On 4 February 2011 14:32, phono 1337 wrote: > > > is the power switch on the rear? if so is there a module for a front panel > switch, im looking at thomann right now but i cant find such a thing. > > does it exist? > > im sure i saw one once
2011-02-04 by phono 1337
is the power switch on the rear? if so is there a module for a front panel switch, im looking at thomann right now but i cant find such a thing. does it exist? im sure i saw one once Pauö [Non-text portions of this message have been removed]
2011-02-04 by Matt
I have some Doepfer patch cables I don't need 5 x 50cm GBP 6.50 5 x 80cm GBP 8.00 8 x 120cm GBP 15.00 Or all of them for GBP 28.00 Plus postage from the UK. Paypal is fine.
2011-02-04 by zaum
> Thanks again Florian. I'll have a look at these videos. > By the way, do you know if this form of synthesis is in any way > related to how the, much maligned, Korg Poly 800 generates its tones? The connection is that many techniques like these relate to organs and to a fair ext
2011-02-03 by avinopsvrecords
--- In Doepfer_a100@yahoogroups.com, Florian Anwander wrote: > > Michael Mccay schrieb: > > Hey guys. So I'm trying to get the arpeggiator within the Dark Energy running, > > and having a little bit of trouble. I'm working in Pro Tools, trying to send it > > a program change comm
2011-02-03 by Florian Anwander
Michael Mccay schrieb: > Hey guys. So I'm trying to get the arpeggiator within the Dark Energy running, > and having a little bit of trouble. I'm working in Pro Tools, trying to send it > a program change command. After two bars into a MIDI track I insert a program > change to #2
2011-02-03 by Michael Mccay
Hey guys. So I'm trying to get the arpeggiator within the Dark Energy running, and having a little bit of trouble. I'm working in Pro Tools, trying to send it a program change command. After two bars into a MIDI track I insert a program change to #22 like the manual state. Howeve
2011-02-02 by Ben Cameron
Hi Bakis, Thanks for listening, hope you enjoy. Ben > > > > Re: New Music > > Posted by: "Bakis Sirros" synth_freak_2000@yahoo.com synth_freak_2000 > > Tue Feb 1, 2011 5:02 am (PST) > > thanks for posting! > > listening to it now, very interesting! > > best regards, > Bakis. > >
2011-02-02 by Tobias Schmitt
Analogue Solutions BD88 � 808 Bass Drum 63� Analogue Solutions GT8 Gate Sequencer 106� Analogue Solutions HH88 � 808 Hihat 106� Analogue Solutions TM88 � 808 Tom 53 � 4 * DIY 3HE Rack 2,5mm 84TE; each 30� 2 * Doepfer A-100G6 19� standard frame; each 263� Doepfer A-100AD5 +5V low