Yahoo Groups archive
Messages
Page 393 of 564 · 28179 messages matched
2005-06-07 by Florian Anwander
Hi >>i really like the analog shift register module idea :-) > May be this can be realized with two A-152. If the 8 T&H outputs of one > A-152 are connected to the switch inputs of the second one. In this case it > is possible to address one of the T&H outputs via clock or CV. Bu
2005-06-07 by Dieter Doepfer
> -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com > [mailto:Doepfer_a100@yahoogroups.com]Im Auftrag von selfoscillate > Gesendet: Dienstag, 7. Juni 2005 14:06 > An: Doepfer_a100@yahoogroups.com > Betreff: [Doepfer_a100] Re: exotic new modules ideas anyone? >
2005-06-07 by sfrules
Exotic? Hmmm... How about *a switch selectable 1 - 8 step Analog Shift Register? *a variable bandwidth VC BPF, with VC Q on each cutoff, and VC of the bandwidth such that it could go from an All-pass filter to a Notch to a No-pass? *a compander module? are these exotic enough for
2005-06-07 by ilanode
Dennis, AFAIK Doepfer sells only jacks for pcb mounting. But I wouldn't mind if the volume discount you've suggested would also apply for these jacks. :), Ingo --- In Doepfer_a100@yahoogroups.com, denis goekdag wrote: > Ingo, > > the best buy for small amounts is Doepfer; typical
2005-06-07 by ilanode
Hello! I'm looking for a source for Cliff jacks for some Doepferized DIY modules preferably within Germany or EC. Since they're not for pcb mounting they should have solder lugs. (I think, S6BB is their manufact. #.) Any help appreciated, Ingo
2005-06-07 by selfoscillate
i really like the analog shift register module idea :-) best wishes ingo --- In Doepfer_a100@yahoogroups.com, sfrules wrote: > > > Exotic? > > Hmmm... > How about > > *a switch selectable 1 - 8 step Analog Shift Register? > > *a variable bandwidth VC BPF, with VC Q on each cutoff
2005-06-07 by esa kotala
Hi Ernst! >1) I see that Doepfer has put the pitch tracker on the overview as a >module in >development, good. >I would like to stress that a range switch compatible to the A110 >osc. >So the old practice of saving ctrl. voltages to tape or an other >medium can be used. By >means
2005-06-06 by Bakis Sirros
hello ernst, many thanks for the details. as you can see, i already created the new polls thanks to your detailed email. best regards, bakis. --- achtung_999 wrote: > --- In Doepfer_a100@yahoogroups.com, Bakis Sirros > wrote: > > hello ernst, > > could you please give us some mor
2005-06-06 by Mathieu le Biomechanoid
Ok thanx for the new exemple ! Concerning the pole of the patch matrix : DIETER IF YOU HEARD ME , MAKE THIS ONE PLEAAAAASE !! that will be cool for sure.... Mathieu --- In Doepfer_a100@yahoogroups.com, "esa kotala" wrote: > very nice > > >From: "selfoscillate" > >Reply-To: Doepfe
2005-06-06 by tkrakowiak
hello, is there a simple way of DIYing doepfer a110 to go beyond audible frequencies (up the scale)? best to all t On 6/6/05, achtung_999 wrote: > --- In Doepfer_a100@yahoogroups.com, Bakis Sirros > wrote: > > hello ernst, > > could you please give us some more detailed info abou
2005-06-06 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like doepfer to release a "VOSIM" oscillator? [a VOSIM oscillator is a classic from the Institute of Sonology. The synthesis method uses a squared-sine (squared in the mathematical sense!) pu
2005-06-06 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like Doepfer to manufacture a Tendency Mask Generator module? (the Tendency mask generator at Sonology is a device which you feed an upper limit and a lower limit as cv inputs [in a doepfer s
2005-06-06 by achtung_999
--- In Doepfer_a100@yahoogroups.com, Bakis Sirros wrote: > hello ernst, > could you please give us some more detailed info about > your suggestions in your email below? > i need more details, in order for me to be able to > create some new polls for your suggestions. > regards, >
2005-06-06 by esa kotala
very nice >From: "selfoscillate" >Reply-To: Doepfer_a100@yahoogroups.com >To: Doepfer_a100@yahoogroups.com >Subject: [Doepfer_a100] new a-113 example >Date: Mon, 06 Jun 2005 07:39:41 -0000 > > >hello, > >here comes a113 example 2. >the patch is basically the same as in the former
2005-06-06 by esa kotala
OT, the thing is i sometimes write drafts of messages to send them later when somebody replies sorry for being confusing =) >From: "selfoscillate" >Reply-To: Doepfer_a100@yahoogroups.com >To: Doepfer_a100@yahoogroups.com >Subject: [Doepfer_a100] Re: BBDs as CV-recorders for there
2005-06-06 by esa kotala
Florian, >So what you describe _is_ a CSQ ;-) how so? >And additional remark, a theremin is not played with gates, but with a >continous cv for the VCA. if you had read the example patch, you'd know that the record gate input was for starting the bbd clock, and to open the record
2005-06-06 by esa kotala
as said before, that's what i wrote yesterday, before being corrected good day >From: "selfoscillate" >Reply-To: Doepfer_a100@yahoogroups.com >To: Doepfer_a100@yahoogroups.com >Subject: [Doepfer_a100] Re: BBDs as CV-recorders for theremin or >ribboncontroller >Date: Mon, 06 Jun 2
2005-06-06 by Florian Anwander
Hi Esa > here's what i thought yesterday > > /// > > inputs: > > * record gate > * record cv/audio > * play gate > * frequency/rate cv1 So what you describe _is_ a CSQ ;-) And additional remark, a theremin is not played with gates, but with a continous cv for the VCA. Florian
2005-06-06 by esa kotala
Hi Dieter, >yes. BBDs are an array of very small capacitors and FETs (used as switche >that pass on the the voltage of a stage to the following stage, a little >bit >like a S&H, that's why it's calle "bucket brigade"). The capacitors are >able >to hold the voltage only a limited
2005-06-06 by Dieter Doepfer
> -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com > [mailto:Doepfer_a100@yahoogroups.com]Im Auftrag von selfoscillate > Gesendet: Montag, 6. Juni 2005 09:55 > An: Doepfer_a100@yahoogroups.com > Betreff: [Doepfer_a100] Re: R2M vs A198 ribbon controller > > >
2005-06-06 by esa kotala
hello! >A single bucket bridge is a sample and hold stage with a bad hold value. >Also there is a signal to noise ratio, which is to my opinion not >bearable for CVs for VCOs. You could modulate the VCO with white noise >too... pitches and tones? no, no here's what i thought yest
2005-06-06 by Dieter Doepfer
> -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com > [mailto:Doepfer_a100@yahoogroups.com]Im Auftrag von Bakis Sirros > Gesendet: Sonntag, 5. Juni 2005 11:35 > An: Doepfer_a100 group; Analogue Systems group > Betreff: Re: [Doepfer_a100] Re: Power ribbon cable
2005-06-06 by Dieter Doepfer
> i have both a198 and r2m and i recommend the r2m. > it has some improvements compared to the a198, > f.e. when the a198 is in hold-mode, the voltage drifts > over time. with the r2m this is not the case. > also the quantizer in the r2m is really handy. > > best wishes > > ingo
2005-06-06 by Dieter Doepfer
> So what's going on there -- does the voltage vanish yes. BBDs are an array of very small capacitors and FETs (used as switche that pass on the the voltage of a stage to the following stage, a little bit like a S&H, that's why it's calle "bucket brigade"). The capacitors are abl
2005-06-06 by selfoscillate
?? i replied to a posting from today, sent at 11:09. now i'm a bit confused, but well, this is quite a "normal" state for me hehehe best wishes ingo --- In Doepfer_a100@yahoogroups.com, "esa kotala" wrote: > as said before, that's what i wrote yesterday, before being corrected >
2005-06-06 by ilanode
Hello Dieter, thanks for your reply which covers my points best. I'll try the "virtual non-quantized mode" later this week at Schneiders Buero. I already spend a (too brief) moment there with the A198 and think the ribbon controller definately a must for me. Also glad to hear tha
2005-06-06 by selfoscillate
as said before, this is not possible with a bbd-device. best wishes ingo --- In Doepfer_a100@yahoogroups.com, "esa kotala" wrote: > hello! > > >A single bucket bridge is a sample and hold stage with a bad hold value. > >Also there is a signal to noise ratio, which is to my opinio
2005-06-06 by Florian Anwander
Hi Jason > i was wondering if anyone is using a softcase for their a100 system. I have a softcase suitable for 3HE gear. I use it sometimes, but my softcase is much deeper than it has to be for the A100. I think if you find a softcase for the standard frame it will be mechanicall
2005-06-06 by Florian Anwander
Hi > So what's going on there -- does the voltage vanish or infinitely approach > some value? A single bucket bridge is a sample and hold stage with a bad hold value. Also there is a signal to noise ratio, which is to my opinion not bearable for CVs for VCOs. You could modulate t
2005-06-06 by ilanode
Hello Ingo, getting a A198 *&* a R2M bcs. the quant. can't be switched off is definately no way to go for me... Anyhow, I had a look into the R2M manual once more. If you choose c or d in Menu 2-1 (and maybe set a high range in Menu 3-4) you can slide over the ribbon without prod
2005-06-06 by selfoscillate
i play an octave cat from time to time and i like it too. the problem is that the cat was available in three versions. the first one had a discrete filter with a fat sound, but bad tracking. the second version had a ssm2040-based filter, which was replaced by an ssm2044 in the th
2005-06-06 by selfoscillate
hello ingo, i don't use my ribbon to mimic a trautonium, so i can't tell you anything about that. it is correct that the r2m quantizer can't be turned off, but i never ran into problems because of that. but to be on the safe side, i bought both a198 and r2m ;-) best wishes ingo -
2005-06-06 by selfoscillate
hello, here comes a113 example 2. the patch is basically the same as in the former example, but of course with "all new" parameters. now the sequence plays three times, until the output changes. output listing: 1. a111 square (source for the a113) 2. a113 output 1 (div 2) 3. a113
2005-06-05 by royce
FS. Analogue Solutions CR78 kick drum module. Or will trade for the 909 kick drum module. in chicago. royce __________________________________ Discover Yahoo! Use Yahoo! to plan a weekend, have fun online and more. Check it out! http://discover.yahoo.com/
2005-06-05 by eyesleeandrews
Hey Nick, I've been using the moniker grandpoohbah for years. When the Detroit Grand Pu Bahs dropped their album, I was like Hey!!!, That's my name..... I got it from the Flintsotnes-- the Fraternal Order of the Water Buffalo... what ever, it's not the name I use professionally.
2005-06-05 by Peter Grenader
That's it! Two other important points: 1) The RS15 uses keyed connectors on its backplane - it will not allow you to plug it in backwards (on that end) because it utilizes the polarizing key inherent in that inline header design. 2) While it may not be the case with all of their
2005-06-05 by boward_k
Hello, Seems right! I called down to TBS and they told me what to do. Though im not sure about the 0volts. ....Speaking of power ribbon cables again(!): Im expecting a big shipment of EFM(3500 series)modules that will need some +/-12VDC. Would anyone recomend (or dissrecomend) me
2005-06-05 by Bakis Sirros
hello, if i remember well, doepfer rack case have their connectors installed is such a way so as the red stripe of the ribbon cables to be downwards. in the Analogue Solutions cabinets, the doepfer connectors in their modules are in such a way installed so as the red stripe to fa
2005-06-05 by analog1k
Anyone got any a100 moog bass type patches. I would like to see Dieter make ARP type oscillator/filter modules, and a 16-step analogue/trigger sequencer.
2005-06-04 by Bakis Sirros
hello ernst, could you please give us some more detailed info about your suggestions in your email below? i need more details, in order for me to be able to create some new polls for your suggestions. regards, bakis. --- achtung_999 wrote: > > A list of things that come to my min
2005-06-04 by n keller
grand poohbah, eh........ he was pretty good. Ever hear that Brand New Heavies album he was on? Anyway, I LOVE the Octave Cat. I've only ever owned the SRM models, never an A-1000 or SRMII. So what version did your boy have? Important to know since...... The original Cat (A-1000)
2005-06-04 by jason kahn
hello list i was wondering if anyone is using a softcase for their a100 system. i currently have the a100 suitcase-version but would like something lighter and easier to get in the cabin of an airplane than the standard doepfer hardcase. thanks very much for any help. best regard
2005-06-04 by esa kotala
Thanks for correcting the headline, Florian >The idea is very nice at the first glance, especially, since it requires >no complex uP-programming. But I think it is not really usable: BBDs >cover only a very short memory amounts, at usable signal quality. So what's going on there
2005-06-04 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like to release a Master Output module? (a bit like the system-100m 131 module. At the minimum it should have four inputs with level and pan, a master volume control and a master stereo ouput
2005-06-04 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: Would you like doepfer to release a Speech-Formant generator module? (similar to something like the phonetic speech chip based synthesizers used in toys like Texas Instrument Speak & Spell Series but w
2005-06-04 by Florian Anwander
Hi Esa The idea is very nice at the first glance, especially, since it requires no complex uP-programming. But I think it is not really usable: BBDs cover only a very short memory amounts, at usable signal quality. Signal quality is for CV much more essential than for audio signa
2005-06-04 by esa kotala
Hi all, this is my first post at this group i shall just throw another idea: could bucket brigade device be used for a module that records control sequences? the ability of playing back theremin, ribbon controller, etc performance in various ways looping or gate triggered, forwar
2005-06-04 by sfrules
Hello, Everything you suggest can be done with midi and a sufficient number of modules. Midi CAN be used with slew. A switch (foot switch?} can be used to turn slew on and off. For instance the dual switch can choose between slewed and direct signal. I leave it to the graphically
2005-06-04 by sfrules
Tap Tempo Generator? Interesting concept!! Would there be space for a gate length knob or in/out? sfrules
2005-06-04 by ilanode
Hello, yes, with modular synth you can always go several ways. Call it a lack of gift (or club foot) but I'd rather use an A198 for not quant. controll. Still I could add a quant. if I'm after a quant. performance and have no hazzle with my slow feet (compared to my fingers). How