Yahoo Groups archive
Messages
Page 76 of 564 · 28179 messages matched
2013-02-04 by James Husted
Forgot - no attachments in this forum! basically The thing I attached was a transistor circuit (2N5088) and some resistors and a LED to drive the output jack. It should isolate the processor fine. I will attach it to the expansion header so no mods to the board itself. That is wh
2013-02-04 by James Husted
Thank You Dieter! I was sure that something like this was available. I will probably make something like this to attach to it: Nice that it is on an expansion connector too. What else shows up on that expansion connector? -James On Feb 4, 2013, at 1:26 AM, yahoo@doepfer.de wrote:
2013-02-04 by Robert Crouch
Yes I did. The problem is fairly consistent where it received midi fine until it's been plugged in for a while, then it just stops. I have to unplug it for anywhere between 10 and 30 minutes before it starts working again. I should probably send it to Analogue Haven and have them
2013-02-04 by yahoo@doepfer.de
> -----Ursprungliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com > [mailto:Doepfer_a100@yahoogroups.com]Im Auftrag von James Husted > Gesendet: Samstag, 2. Februar 2013 08:41 > An: Doepfer_a100@yahoogroups.com > Betreff: [Doepfer_a100] Can I mod a A-152 to do this? > > > I
2013-02-04 by yahoo@doepfer.de
Did you (re-)install a jumper to the pin header JP4 on the interface/supply board instead of the glide option ? Best wishes Dieter Doepfer > -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com > [mailto:Doepfer_a100@yahoogroups.com]Im Auftrag von Robert Crouch >
2013-02-02 by Jesse Buehler
Perhaps, but keep in mind it also covers the a-161, a-149-1 and the gate aspects of the a-152. For all of that, $250 is not that bad. Sent from my iPhone On Feb 2, 2013, at 3:58 PM, James Husted wrote: > The V-Gate function mentioned as "A clock output is available that produces
2013-02-02 by James Husted
The V-Gate function mentioned as "A clock output is available that produces a 1 millisecond (ms) pulse for each change of output state." is exactly what I am looking for from the A-152. I am hoping that there is an internal logic function of the A-152 that can be exploited to do
2013-02-02 by Jesse Buehler
James, Synthetic Sound Lab's V-Gates will do this. In its Analog mode, cv input can be swept in different ways to its 8 outputs as triggers. It also produces a single trigger out each time that threshold of each trigger level is passed. It's a very complex module, and is capable
2013-02-02 by James Husted
I recently got an A-152 and am using it to select the columns of two of my PGM-4X4 programmers to make sequences that can have programmable patterns to them. What I would like is to mod the A-152 so that I can add an output that produces a trigger whenever the A-152 addresses a n
2013-02-01 by Robert Crouch
Turns out it's not the glide option after all. I think I need to send it in for repair. :-( --- In Doepfer_a100@yahoogroups.com, "Robert Crouch" wrote: > > I installed the glide kit to my Dark Energy a while ago and lately the internal midi-cv converter has been giving me problem
2013-01-28 by yahoo@doepfer.de
> So have 2 A-196 PLLs that i've been fooling around with -Raul's > World of Synths latest video on the A196 pushed me to play with > them today. I never bothered to ever compare them. Each one's > oscillator is tuned differently. I can't get them to match. One > is lower than th
2013-01-28 by Raul
Thanks for that clarity. I'll keep that in mind. I'll include that addendum to the video information for the next few. All the best. Raul Pena --- In Doepfer_a100@yahoogroups.com, wrote: > > > Just a minor question on the PLL. In the manual it states that > > PC2 is linked to the
2013-01-28 by yahoo@doepfer.de
> Just a minor question on the PLL. In the manual it states that > PC2 is linked to the LED. However there is a fair amount of > activity occurring when using the other two modes. What is the > light indicating if not locking? > > Thanks for any help in understanding this. > > Ra
2013-01-28 by Raul
Just a minor question on the PLL. In the manual it states that PC2 is linked to the LED. However there is a fair amount of activity occurring when using the other two modes. What is the light indicating if not locking? Thanks for any help in understanding this. Raul Pena
2013-01-26 by christian ienni
belated happy new year to everyone! :-) new track for the new year - "entropy engine 1" some shamelessly indulgent berlin-school sequenstravagasm wankery on the big A100 (5xG6). it does get stanger as it goes on, and very sorry about the clipping in a couple places. enjoy! http:/
2013-01-25 by metronomezine
So have 2 A-196 PLLs that i've been fooling around with -Raul's World of Synths latest video on the A196 pushed me to play with them today. I never bothered to ever compare them. Each one's oscillator is tuned differently. I can't get them to match. One is lower than the other. W
2013-01-25 by achtung_999
The worst thing that might happen will be fuses blowing regularly. That is a sign. On Thu, Jan 24, 2013 at 9:43 PM, christian ienni wrote: > ** > > > ah, i understand. since all of my cases are the newer 1200mA PSU2 > versions, i doubt i'm pushing any limits, since as i said i've
2013-01-24 by christian ienni
ah, i understand. since all of my cases are the newer 1200mA PSU2 versions, i doubt i'm pushing any limits, since as i said i've never noticed any problems, or suddenly "released the magic smoke" ;-) . one of these days i'll have to play around on modulargrid.net and see what's a
2013-01-24 by achtung_999
For the record: I just reordered all modules so I'm within limits again... On Thu, Jan 24, 2013 at 11:30 AM, achtung_999 wrote: > Well to be honest I never noticed a thing. Until I started, for fun, to > build my rig on http://www.modulargrid.net and noticed that I was way > over
2013-01-24 by achtung_999
Well to be honest I never noticed a thing. Until I started, for fun, to build my rig on http://www.modulargrid.net and noticed that I was way over 650mA with one case. So I guess that proves Doepfer's stuff is quite durable (the case was a Doepfer case holding only Doepfer module
2013-01-24 by christian ienni
out of curiosity, what is the symptomology you have noticed, i.e. what specifically happens that leads you to think there's a current issue? so i can maybe watch for something similar just in case. ________________________________ From: achtung_999 To: Doepfer_a100@yahoogroups.co
2013-01-23 by achtung_999
I seem to have been running way too much in one of my old 6U cases for more than a year I noticed... I have to hand to the maker of http://www.modulargrid.net, it's a great tool to calculate answers to these kind of questions... On Wed, Jan 23, 2013 at 10:08 PM, christian ienni w
2013-01-23 by christian ienni
hmmm.... maybe i should do some homework! i've always just gotten the modules i wanted and installed them where they fit, and have never even looked at power ratings or anything. i have 5 G6 racks (PSU2) and 2 mini-cases and have never seemed to have any problems because of curre
2013-01-23 by yahoo@doepfer.de
> Thank you very much, that is reassuring, I was working on the > assumption that the maximum total was 650ma. > > Best wishes It depends upon the built in power supply ! The old version A-100TN12 had only 650mA (manufactured until about 2001), the new version A-100PSU2 has 1200
2013-01-23 by achtung_999
Actually, it was 650mA for the cases with the old powers supply. Do you have a PSU 2 or 1 in the case? The PSU 2 is a round transformer core and PSU 1 is a small black plastic transformer. PSU 2 is 1200mA the PSU 1 is 650mA. On Wed, Jan 23, 2013 at 12:43 PM, isoldeandisobelle wro
2013-01-23 by isoldeandisobelle
Yes, it is the PSU2 version. Thanks again....very helpful. --- In Doepfer_a100@yahoogroups.com, wrote: > > > Thank you very much, that is reassuring, I was working on the > > assumption that the maximum total was 650ma. > > > > Best wishes > > It depends upon the built in power s
2013-01-23 by achtung_999
Way within the limits. The Doepfer 6U cases are rated 1,2A I believe. Ernst On Wed, Jan 23, 2013 at 12:09 PM, isoldeandisobelle wrote: > ** > > > Hi, > > In my 6U case, the current usage of all modules installed amounts to the > 650ma limit, this includes the A-113 Sub Harmonic g
2013-01-23 by isoldeandisobelle
Thank you very much, that is reassuring, I was working on the assumption that the maximum total was 650ma. Best wishes --- In Doepfer_a100@yahoogroups.com, achtung_999 wrote: > > Way within the limits. The Doepfer 6U cases are rated 1,2A I believe. > > Ernst > > > On Wed, Jan 23,
2013-01-23 by isoldeandisobelle
Hi, In my 6U case, the current usage of all modules installed amounts to the 650ma limit, this includes the A-113 Sub Harmonic generator, which is rated at 30ma, I have not included the 5v low cost adapter in this total - although it it installed.....am I still within safe limits
2013-01-21 by Robert Crouch
Thanks! --- In Doepfer_a100@yahoogroups.com, Florian Anwander wrote: > > Hi > > Jumpers like these are standard: They are 0.1 Inch / 2.54 mm Jumpers. > Everyone who has an old Computermainboard laying around could pick a > jumper from it and give it you. > > Regarding the Interfa
2013-01-21 by Robert Crouch
LOL no insult at all. Yes I tried that first and for a while it was helping. Yesterday not so much. :-( --- In Doepfer_a100@yahoogroups.com, Sean Dynan wrote: > > I used to have a problem very like this with the Dark Energy MkI. At the risk of insulting your intelligence have you
2013-01-21 by Robert Crouch
Wow, thank you Dieter! --- In Doepfer_a100@yahoogroups.com, wrote: > > > I installed the glide kit to my Dark Energy a while ago and > > lately the internal midi-cv converter has been giving me > > problems. Every so often it just stops responding to any incoming > > midi signal,
2013-01-21 by Sean Dynan
I used to have a problem very like this with the Dark Energy MkI. At the risk of insulting your intelligence have you tried unplugging and reinserting the USB cable? -- Sean
2013-01-21 by yahoo@doepfer.de
> I installed the glide kit to my Dark Energy a while ago and > lately the internal midi-cv converter has been giving me > problems. Every so often it just stops responding to any incoming > midi signal, either through the USB or midi ports. I reinstalled > the glide control and
2013-01-21 by Florian Anwander
Hi Jumpers like these are standard: They are 0.1 Inch / 2.54 mm Jumpers. Everyone who has an old Computermainboard laying around could pick a jumper from it and give it you. Regarding the Interface itself I cannot help you unfortunaly. Florian Am 21.01.2013 03:05, schrieb Robert
2013-01-21 by yahoo@doepfer.de
> Hi > > Hoping that someone may know what I should do here. I have a A190 that is > about 2 years old. Recently the pitch from CV 1 output has started to > swing wildly around and often the root note seems to move by a few > semitones. Is there a possible solution to this or is
2013-01-21 by Robert Crouch
I installed the glide kit to my Dark Energy a while ago and lately the internal midi-cv converter has been giving me problems. Every so often it just stops responding to any incoming midi signal, either through the USB or midi ports. I reinstalled the glide control and that seems
2013-01-20 by David Kaiser
Thank you Dieter! That is the confirmation that I was looking for. On 1/7/13 6:25 AM, yahoo@doepfer.de wrote: > > > You may simply connect the "hot" midi output signal (i.e. not the GND pin) > of the first module to the "hot" midi input of the second module. > Connecting > the GN
2013-01-18 by David Passam
Hi Hoping that someone may know what I should do here. I have a A190 that is about 2 years old. Recently the pitch from CV 1 output has started to swing wildly around and often the root note seems to move by a few semitones. Is there a possible solution to this or is the module b
2013-01-12 by Rudy Toussaint
Doepfer A-140 . Cheap and snappy! ________________________________ From: Peter Sedin To: doepfer_a100 Sent: Friday, January 11, 2013 7:36:10 PM Subject: [Doepfer_a100] WTB eurorack modules Wiard Envelator Wiard XMIX Intellijel Planar DOEPFER - A-151 A-162 A-170/171 A-185 A-186-1
2013-01-12 by Peter Sedin
Wiard Envelator Wiard XMIX Intellijel Planar DOEPFER - A-151 A-162 A-170/171 A-185 A-186-1 A-167 and adsr/envelope modules, open for suggestions -- Mvh Peter H.K Sedin [Non-text portions of this message have been removed]
2013-01-11 by Peter Sedin
ok cool! :) 2013/1/10 > ** > > > > yes! but i cant modulate the inputs can I? > > I want to be able to switch modulation sources with CV, sum of > > that, routed > > to one modulation input. > > like for example= one second sinewave, next second squarewave, two second > > random,
2013-01-10 by yahoo@doepfer.de
> yes! but i cant modulate the inputs can I? > I want to be able to switch modulation sources with CV, sum of > that, routed > to one modulation input. > like for example= one second sinewave, next second squarewave, two second > random, etc (for example) > thanks for your reply
2013-01-09 by Peter Sedin
that Intellijel Planar looks exaktly what i want! and then some :) 2013/1/9 Peter Sedin > sweet :) > > > 2013/1/9 Ded Mousie > >> ** >> >> >> >> > I want to be able to switch modulation sources with CV >> >> Are you looking to switch between inputs A, B, C, D, or do you want a >>
2013-01-09 by Peter Sedin
sweet :) 2013/1/9 Ded Mousie > ** > > > > > I want to be able to switch modulation sources with CV > > Are you looking to switch between inputs A, B, C, D, or do you want a > smooth fade between the sources? For wave sequencing or even modulation > routings, seems a programmable
2013-01-09 by Ded Mousie
> I want to be able to switch modulation sources with CV Are you looking to switch between inputs A, B, C, D, or do you want a smooth fade between the sources? For wave sequencing or even modulation routings, seems a programmable fade between sources would be better, unless you s
2013-01-09 by Martin Klang
On 9 Jan 2013, at 17:37, Peter Sedin wrote: > yes! but i cant modulate the inputs can I? > I want to be able to switch modulation sources with CV, sum of that, routed > to one modulation input. > like for example= one second sinewave, next second squarewave, two second > random,
2013-01-09 by Peter Sedin
yes! but i cant modulate the inputs can I? I want to be able to switch modulation sources with CV, sum of that, routed to one modulation input. like for example= one second sinewave, next second squarewave, two second random, etc (for example) thanks for your reply tho! peter 201
2013-01-09 by Martin Klang
If I understand you correctly then the A-138m Matrix Mixer will do what you want, and in a straight-forward way. Up to four modulation sources can be assigned, by mixing them together, to up to four parameters. I find it super useful. In bi-polar mode it's a bit like the patch ro
2013-01-09 by Peter Sedin
Hello guys! one of my favorite thing to do in my dave smith Evolver is to assign diffrent modulation tracks with diffrent types of LFO, all assigned to the same parameter, one cool way to make almoust knobmovement-like modulation.. another famous example is the start of "we are t