Yahoo Groups archive
Messages
Page 249 of 564 · 28179 messages matched
2008-06-08 by David Bulog
Hi Wolfgang Can you please tell me how to test three voltages are ok? -12V/+12V/+5V on A-100P thanks David On 8/06/2008, at 10:22 AM, wolfgthiel wrote: > Hi David > > Was the A-190 working before you did the reset? > Have you checked if all three voltages are ok? -12V/+12V/+5V. >
2008-06-08 by David Bulog
looking at archives for 230v systems 100 or 125mA slow blow fuse is supposed to be correct one for 115v systems 200 or 250 mA slow blow is supposed to be correct one can anyone tell me why 230v systems take half the value of US systems thanks David
2008-06-08 by E_K_
As I await an announcement about the monster base cases, I'm wondering how one would go about flying on an airplane with one of these. It's obviously too big for carry-on, but it's not a flight case so you couldn't check it directly -- I suppose one would have to pack it inside s
2008-06-08 by wolfgthiel
Hi David The easierst point to test is the bus board (you might have to take a few modules out for good access). The 16 pol plugs are label with the voltages (check between GND and +5V/-12V/+12V). Please do this only if you familiar with this type of work as otherwise you might d
2008-06-07 by Monroe Eskew
Hello, The top VCA on my A132 will pass a small amount of signal even if 0 volts are present at the CV in. The bottom VCA does not have this problem. Adjusting the "offset" on the circuit board doesn't fix this. Is there anything I can do? Thanks, Monroe [Non-text portions of thi
2008-06-07 by E_K_
The "30 cm" Doepfer cable I just pulled out to measure is almost 34 cm tip-to-tip, and just under 27 cm if you measure just the actual cable, excluding the thicker 'grip' part (sorry I don't know the terminology). From the base of each metal plug, the length is 31 cm. Likewise th
2008-06-07 by wolfgthiel
Hi David Was the A-190 working before you did the reset? Have you checked if all three voltages are ok? -12V/+12V/+5V. I don't think there is a fuse in the A-190 modul (just had a look at my one)and I'm not familiar with the Doepfer power supply. In general you could take the fus
2008-06-07 by David Bulog
I went do a full reset of the A-190 by powerup while holding buttons 1-4 on power up When I powered the unit on the lights on the A-190 came on momentarily and then no power. Has anyone had a similar issue BTW -How do I check if fuse is vlown thanks David [Non-text portions of th
2008-06-06 by Bakis Sirros
hello, its cable length between plugs then. the cable lengths were suggested by another email (from Dieter). these are not my choises, so i cannot be really sure. but, in order for Dieter to suggest 10cm, i assume its cable length between plugs... but, i just measured one of the
2008-06-06 by Silas Johansen
Bakis, Would you please specify whether we're voting on the length tip-to-tip or the cable length between plugs? Also, as the plugs on my Doepfer patch cables are about 4.5cm long a 10cm tip-to-tip cable would only have an "effective length" of about 1cm and thus could not be use
2008-06-06 by Maxime
Yep, percussion comes from the A100 too, noise, resonating Xtreme filter, ADSR, delay and reverb. Max. --- In Doepfer_a100@yahoogroups.com, "Doug" wrote: > > Ha ha, I love the video, although it looks painful staring into that > light! Is the percussion coming out of the A-100 to
2008-06-06 by Herman Pearl
Want To Buy Used Doepfer A-170 Dual Slew Limiter A-164-1 manual gate A-137 Wave Multiplier A-149-1 Quantized/Stored Random Voltages cheap US to US shipping is best for me I have a lil paypal $ to drop Also have an A-199 to trade djsoysos@yahoo.com
2008-06-05 by Doug
Ha ha, I love the video, although it looks painful staring into that light! Is the percussion coming out of the A-100 too? Great stuff. Thanks, Doug
2008-06-05 by Bakis Sirros
nice!! :-) --- beebsynthesizers wrote: > New Isidore video /w MFB videoscope module, online > on youtube. > Posted by: "Maxime" francois.maxime@gmail.com > damaged_meat > Wed Jun 4, 2008 3:19 pm (PDT) > > Hi list, > Just uploaded a new video featuring Isidore, my DIY > interactiv
2008-06-05 by beebsynthesizers
New Isidore video /w MFB videoscope module, online on youtube. Posted by: "Maxime" francois.maxime@gmail.com damaged_meat Wed Jun 4, 2008 3:19 pm (PDT) Hi list, Just uploaded a new video featuring Isidore, my DIY interactive sexy robot cabinet. Most sounds are from the A100 and v
2008-06-05 by Bakis Sirros
ok, a new poll has been created for the cable length of a new short patchcord. please vote soon, as this poll will remain open for only 2 weeks. thanks, Bakis. --- hardware@doepfer.de wrote: > > yeah, short patchcables are very important. > > I have them from 8cm up to 15cm in 2c
2008-06-04 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: What cable length would you want a new Doepfer short patchcord to have? o 10cm o 15cm o 20cm To vote, please visit the following web page: http://groups.yahoo.com/group/Doepfer_a100/surveys?id=12773141
2008-06-04 by Hans Greuber
Hi; I´ve been out for some time. I just saw the doepfer matrix pin project and seem cool. I own a sinthy and a VCS3 MKI and I guess they are unimitable so not sure what kind of new live can do that matrix to the Doepfer other than usual patch cables but it could be nice. In order
2008-06-04 by Monroe Eskew
My vote is for 15cm On Wed, Jun 4, 2008 at 9:42 AM, wrote: > > yeah, short patchcables are very important. > > I have them from 8cm up to 15cm in 2cm increments ( more less ) . > > even 15cm is much too long many times. > > ( I think measurement was between the plugs) > > > > I w
2008-06-04 by Maxime
Hi list, Just uploaded a new video featuring Isidore, my DIY interactive sexy robot cabinet. Most sounds are from the A100 and video shows all the funny stuff about this crazy cabinet I've been working on for a while now. Isidore now has a screen in his head showing waveforms and
2008-06-04 by Silas Johansen
If two standard 8 HP wide modules each with 5 sockets and 5 pots are mounted next to each other a 18.5cm tip-to-tip cable will allow you to connect any socket on one to any socket on the other. I think an extra 1½cm slack wouldn't hurt, so 20cm tip-to-tip sounds to me like a good
2008-06-04 by hardware@doepfer.de
> yeah, short patchcables are very important. > I have them from 8cm up to 15cm in 2cm increments ( more less ) . > even 15cm is much too long many times. > ( I think measurement was between the plugs) > > I would take a bunch too if somebody gets them Manufactured. > ( no handsp
2008-06-04 by hardware@doepfer.de
> hi, i have the need to run those Modules on 15volts: > 1. A-160/ 161 > 2. A-151 > 3. A-150 > > can i power them up with 15 Volts. > It would easen up things here alot. > found nothing with the surch function > > is there somewhere a complete list of which Doepfer Modules can ru
2008-06-04 by hemi_ch
Yes, a Poll would be perfect ! thanks. that you cannot make every lenght is absolutely clear. 20cm tip to tip is a very good lenght if you just like to make one more lenght Dieter, please make shure that we all speak from tip to Tip lenght when making the Poll H.c. --- In Doepfer
2008-06-04 by hemi_ch
yeah, short patchcables are very important. I have them from 8cm up to 15cm in 2cm increments ( more less ) . even 15cm is much too long many times. ( I think measurement was between the plugs) I would take a bunch too if somebody gets them Manufactured. ( no handspoldering ) H.C
2008-06-04 by hemi_ch
hi, i have the need to run those Modules on 15volts: 1. A-160/ 161 2. A-151 3. A-150 can i power them up with 15 Volts. It would easen up things here alot. found nothing with the surch function is there somewhere a complete list of which Doepfer Modules can run on +- 15 Volts ? t
2008-06-04 by hardware@doepfer.de
> Hi, > > More a question for Dieter. Last week I took a walk to Technopolis, our > canadian Doepfer dealer, only to see that they are now closed. I know that > MoogAudio is getting on the modular buisness (they recieved PlanB shipments > already), but when I ask about Doepfer pr
2008-06-04 by amnesia
I have owned a VCS3 and currently own a Synthi AKS. I also have a Serge and a Euro system... It depends on many things 1. What style of music you want to do on it. I am totally into improv electronics nowdays and can get a very similar sound from my euro as I have a Doep Spring R
2008-06-04 by Bakis Sirros
hello, the A123 HP filter is still available, now even lower price (63% of new price): 91.35 USD payment via paypal (add 3.5% for paypal fees) shipping 9usd to worldwide. thanks, Bakis. Bakis Sirros - Parallel Worlds / Interconnected / Memory Geist [Doepfer_a100] group owner www.
2008-06-04 by Sylvain Delisle
Hi, More a question for Dieter. Last week I took a walk to Technopolis, our canadian Doepfer dealer, only to see that they are now closed. I know that MoogAudio is getting on the modular buisness (they recieved PlanB shipments already), but when I ask about Doepfer products they
2008-06-03 by James Husted
I have been on this search for a while. I once owned 2 AKSs and a VCS3. I have tried to re-create the "feel" of them and found a few things about the EMS designs that become the challenge - one is the CV/ Octave range is very non-standard. It is if I remember correctly around 0.3
2008-06-03 by Bakis Sirros
for sale: A126 Frequency Shifter (now not available from doepfer at the moment...) price 70% of new: 182 USD payment via paypal. add paypal fees 3.5% shipping to anywhere 9USD. ribbon cable and screws included, of course. in fine working and cosmetic condition. thanks, Bakis. Bak
2008-06-03 by jeswa
thanks
2008-06-03 by nicholas_kent
- > and this is my question. I know analogue solutions make the filter and > trapezoid and i know some kind of pin matrix is coming soon, but I > wonder if anyone has found doepfer or other modules which replicate the > ways the VCS3 mixers and gain stages overdrive and saturate.
2008-06-03 by David Salter
Hi Richard, Analogue Systems make the modules. The Analogue Systems RS95 is also a close representation of the VCO's and they will also do multi turn pots with vernier dials too. As for the gain stages, the VCS3's are quite basic or should I say crude which is what helps give the
2008-06-03 by Richard Scott
Hi I am lucky to be sitting with a rather knackered but still working (borrowed) EMS VCS3. Its a synth I've wanted to get my hands on for a long time and i must say its no disapointment. the sound is incredible and the interface, for me, is by far the friendliest I ever had on a
2008-06-02 by theglyph2000
--- In Doepfer_a100@yahoogroups.com, "thomasborax" wrote: > > > > > > My first idea: the internal connection is broken. It's a blank wire > that > > connects the solder point "JP4" of all four boards, located behind > the mix > > polarizer potentiometer at the pcb edge. But I'd w
2008-06-02 by daad_noise
--- In Doepfer_a100@yahoogroups.com, "Tim Stinchcombe" wrote: > > Hi Peter, > > I've just had a quick play around with this idea, and thought I'd > offer up a few comments. > > The transistors in the MC1496 chip used for the Y input are kept > biased at around 6V by the coupling
2008-06-02 by Monroe Eskew
Thanks for the link. I would still have an interest in even shorter cables. The purpose is to patch a bunch of adjacent modules while minimizing the wire mess. I was thinking about making some myself. I could order in bulk and sell them to others for not much... probably $2 US ea
2008-06-02 by thomasborax
> > My first idea: the internal connection is broken. It's a blank wire that > connects the solder point "JP4" of all four boards, located behind the mix > polarizer potentiometer at the pcb edge. But I'd wonder why this should > break if the module is connected to Peter Grenader
2008-06-02 by hardware@doepfer.de
> Everything else is working OK but I was using the Mix Out (LFO out) to > drive my Plan B model 13 when it suddenly stopped outputing its CV signal! > > Any thoughts on what could have gone wrong or how to fix it would be > greatly appreciated! > > Cheers, > theglyph My first id
2008-06-02 by hardware@doepfer.de
> the exact same happens to one of my two doepfer > vu-meters lights too! > I just tap the plastic screen a bit and the LIGHT > TURNS ON AGAIN. > ALTHOUGH, for the last months, I didn't have any > problems at all with this light. > > best regards, :-) > Bakis. If you have a techn
2008-06-02 by hardware@doepfer.de
> hi list, > > i would like to replace the bulb in my doepfer voltemeter module, > but am not sure how to do so. > has anybody done this? does it require chainging the entire meter? > > royce Two different types of meters were used in the A-197. A version with removeable bulbs an
2008-06-02 by David Salter
Try SMS http://syntheticmusicsystems.co.uk/ Although not listed on the site, Andy provides short patch cables with a MARS/Planet 7 setup to interconnect the two. David * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * David Salter Senior Consultant Tho
2008-06-02 by rrooyyccee
wow, so the solution is to tap the glass? seems lame. i wonder if it would be easier to replace the entire meter assembly? royce
2008-06-01 by theglyph2000
Everything else is working OK but I was using the Mix Out (LFO out) to drive my Plan B model 13 when it suddenly stopped outputing its CV signal! Any thoughts on what could have gone wrong or how to fix it would be greatly appreciated! Cheers, theglyph
2008-06-01 by Monroe Eskew
Does anyone know if/where one can buy extremely short patch cables, say around 10-20 cm? Monroe [Non-text portions of this message have been removed]
2008-06-01 by floris vanhoof
i had the same question weeks ago, and asked every (internet/ebay,...) seller i could find, and nobody had it. you might find 20 cm. but i think 10 cm and a lot of different colors (so you could see what you do & touch the knobs) would be great! let me know if you find anything.
2008-06-01 by Florian Anwander
HI Bakis > the exact same happens to one of my two doepfer > vu-meters lights too! > I just tap the plastic screen a bit and the LIGHT > TURNS ON AGAIN. > ALTHOUGH, for the last months, I didn't have any > problems at all with this light. The light bulbs in voltmeter are steady p
2008-05-31 by davevosh@aol.com
In a message dated 5/31/2008 12:12:50 PM Pacific Standard Time, synth_freak_2000@yahoo.com writes: the exact same happens to one of my two doepfer vu-meters lights too! I just tap the plastic screen a bit and the LIGHT TURNS ON AGAIN. ALTHOUGH, for the last months, I didn't have