Re: Is there a way to send 127-val?
2012-05-10 by Gil Brand
Thank you very much Royce!!! Gil
Messages
Browse messages
Page 35 of 110 · 5497 messages matched
ableton question
2012-05-10 by modulardancelwerk
Hi to all, this is my first post, i want to know how can i do in ableton live the following, i have a bcr2000 and bcf2000 (only bcf in mackie control), i want
Re: Is there a way to send 127-val?
2012-05-07 by Royce
Hi Gil ... You might think it depends on what the range of values (within the byte) you need. Both byte ranges must be the same. If you are using 0 to $3F or
Re: Is there a way to send 127-val?
2012-05-06 by Gil Brand
Thank you Royce! I m using a Yamaha A4000 sampler. I don t know why is the value split but all data within a SysEx message should be nibblized ... There are
Re: Is there a way to send 127-val?
2012-05-03 by Royce
Hi Gil ... The BC encoders have 96 notches per rotation. If you set the resolution to 96 all output values are sent. If you set the resolution for 96 x 2 =
Re: Is there a way to send 127-val?
2012-05-02 by Gil Brand
Hi Royce, I m excited that such a cross fade can be done. However, I can t figure out the way you did it. Can you please relate to the following passage that
FL Studio Relative mode support
2012-04-29 by k0mp0 ser
Has anyone had any luck linking knobs to FL Studio in one of the BCR2000 knobs relative modes? Thanks, Ryan
Re: newbie
2012-04-27 by tb_bob
Hey there. I am a newbie as well. Did you mention a pg 300 patch?? Where can I find such a beast? Thanks. . .
Re: Midi Yolk installation and setup... questions!?!
2012-04-27 by daz303@rocketmail.com
Hi Mark Very helpful information my friend.... I will try it out as soon as i am back (about to leave on a work trip)... I just re-posted this question before
Re: BCF-2000 - limited communication
2012-04-27 by Mark v.d. Berg
... Have you managed to fix this yet? As far as I know, if a device in the B-Controls window is Disabled , this can only mean that its MIDI input and output
Please help - connecting BCM, Midi Yoke and Ableton
2012-04-27 by daz303@rocketmail.com
Hi all Can someone please tell me how I should configure BC manager, Midi Yoke and Ableton Live 8? I have installed the Ableton mackie control preset 5.0a
Re: Midi Yolk installation and setup... questions!?!
2012-04-27 by Mark v.d. Berg
... This message might help a bit: http://launch.groups.yahoo.com/group/bc2000/message/3793 ... For me it works like this (under Windows 7, 64-bit): I put the
Re: [bc2000] Finally have success with BC Manager!!
2012-04-27 by eivind@fivelsdal.no
This post goes into my STORE folder. Thanks! Eivind
Sysex help with roland d110 and kawai k1
2012-04-26 by danyu100
I downloaded the roland d110 preset for the bcr2000, but I don t know how to get it working. It contains 4 sysex files. I tried sending 1 file with sysex
Midi Yolk installation and setup... questions!?!
2012-04-26 by daz303@rocketmail.com
OK... I m sure everyone s had enough of these questions by now but we re almost finished... So far: Uninstalled and reinstalled drivers, controllers and BC
Finally have success with BC Manager!!
2012-04-26 by daz303@rocketmail.com
Greeting all... Well I am VERY happy and a little bit relieved to say that I ve finally got BC manager to work. In the end it resorted to brute force.... I
Re: Blinking light on push encoder ... now what?????
2012-04-25 by daz303@rocketmail.com
Adam - ... Now THAT is something I never knew.... That s really great and well worth playing with. I m getting bombarded with helpful suggestions... thanks to
Re: [bc2000] Re: Blinking light on push encoder ... now what?????
2012-04-25 by Martin Klang
... There s a built-in tutorial for the bcr2000 template in Live. If you can t find it, try searching the ableton forum, there s quite a lot of info there
Re: [bc2000] Re: Blinking light on push encoder ... now what?????
2012-04-25 by Adam A.
If you re using the dump method in my previous reply, the BCR displays and retrieves the settings for whatever plugin is highlighted in your rack. I don t
Re: Blinking light on push encoder ... now what?????
2012-04-25 by -
Try an older version of the preset http://launch.groups.yahoo.com/group/bc2000/files/Presets/Abeton%20Live%20Mackie%20Presets/
Re: Blinking light on push encoder ... now what?????
2012-04-25 by daz303@rocketmail.com
Hi Adam I ve done that and on most times I can get the BCR and Ableton to connect... I can see the effects of some of the rotary controllers eg. the lowest row
Re: [bc2000] Re: Blinking light on push encoder ... now what?????
2012-04-25 by Adam A.
Seems like you re missing the obvious, so forgive me if this something you ve tried or that you re avoiding: In the MIDI tab of your Ableton preferences,
Re: Blinking light on push encoder ... now what?????
2012-04-25 by -
BCmanager not working? What OS? It should be working fine. I have had no trouble with it. Are you on usb and what mode is the bcr in? Don t try the java thing
Re: Blinking light on push encoder ... now what?????
2012-04-25 by daz303@rocketmail.com
Hi k5kip Thanks for your reply. I did try your preset... in fact, it was the first thing I did try but I have a serious bug somewhere in my gear. I can t get
Re: Blinking light on push encoder ... now what?????
2012-04-25 by -
I will suggest, again, that you try my preset for a few days, just like it is on a project. After you get it working, only then try to move items around. I
Blinking light on push encoder ... now what?????
2012-04-25 by daz303@rocketmail.com
Hi everyone (again).... back again with another dumb question. I am trying to write data to the 8 rotary push encoders. Specifically, I am trying to make my
Re: BCR-2000 Preset not saving??... Makes using Ableton Live a pain in the ableton.
2012-04-23 by daz303@rocketmail.com
Thanks a lot!! Will try it out and let you know. cheers daz
Re: BCR-2000 Preset not saving??... Makes using Ableton Live a pain in the ableton.
2012-04-23 by -
Hey, A couple of comments. Try bcmanager. Try my(many ppl worked on it) mackie preset. http://oneleaf.heliohost.org/wp/bcr2000-page/ Read me included. Try it.
Re: Help - I can't write Presets to BCR-2000 using BC Editor
2012-04-22 by daz303@rocketmail.com
Hi Royce Thanks for the info.... It worked a treat!!! Why Oh why can t things work like they say they will in the glossy brochures??? cheers daz
Re: Help - I can't write Presets to BCR-2000 using BC Editor
2012-04-22 by Royce
... 8P sysex patch. I Booted up BC Editor and I could import the patch into the Editor section but the option to load the patch to the Hardware section (ie.
Re: BCR2000 and noOS message
2012-04-22 by maxichip99
Since I cannot find any valid instructions on how to link a BCF-2000 with BC Manager via USB I finally managed it this way: Create the new syx file with
Re: BCR-2000 Preset not saving??... Makes using Ableton Live a pain in the ableton.
2012-04-22 by saxutopia
Apologies for brevity of previous post I was on mobile phone which is torturous for typing. I read many of the posts regarding this peculiarity, but eventually
Re: BCR-2000 Preset not saving??... Makes using Ableton Live a pain in the ableton.
2012-04-22 by saxutopia
Daz, I had a similar experience getting mine to handshake, I found the manual very confusing, and part of my job is IT administration, I eventually got it to
BCR-2000 Preset not saving??... Makes using Ableton Live a pain in the ableton.
2012-04-22 by daz303@rocketmail.com
Hi again ... another problem, another question... Are the 32 presets in the BCR2000 separate from each other? My BCR2000 came preloaded with a selection of 14
Help - I can't write Presets to BCR-2000 using BC Editor
2012-04-22 by daz303@rocketmail.com
I recently purchased a BCR2000 and had a bit of a play with it yesterday.... not much good news to report I m afraid. I m posting another question on a
Re: BCF-2000 - limited communication
2012-04-19 by maxichip99
I tried with the graphic editor and the BCF ist identified as enabled device with input and output functionality. However, with the BC Manager I always get
Re: Increment -1 and +1 SysEx with Buttons
2012-04-19 by djheikotnt
Thanks man it works great :-) in my post I meant that i use BC convert :-) but i wrote I need BC Convert!...Sorry for the wrong Info... The Mountain Utilities
Re: Increment -1 and +1 SysEx with Buttons
2012-04-19 by Royce
You could use Mark s graphic editor . If nothing else you should get his excellent pdf on the BCL (Behringer Control Language) A link to Mark s web page is in
Increment -1 and +1 SysEx with Buttons
2012-04-18 by djheikotnt
Hey Ladys :-) I need BC Convert for Mac OSX . I found the B-Control Token-Reference page (german language) but I do not understand some SysEx configurations
Re: Please Help - Controlling JX-8P parameters using a BCR-2000 (long)
2012-04-16 by daz303@rocketmail.com
Hi and thankyou to all of you who posted help and suggestions.. I received my BCR2000 today and hooked it up to my JX8P and it worked brilliantly!!!!! I simply
Re: BCF-2000 - limited communication
2012-04-14 by Royce
You can program the BCF from my editor (File section) using the BC2000 programming language or you can get Mark s graphic editor (link is in the Link area -
Re: BCF-2000 - limited communication
2012-04-14 by maxichip99
Let me add that I cannot allocate an input or outpout channel:all ports are shown as disabled.
BCF-2000 - limited communication
2012-04-14 by maxichip99
Hi, I am new in this this forum and a new user of bcf-2000. I want to use my bcf-2000 with DasLight (version DVC3). For this the presets have to be
New file uploaded to bc2000
2012-04-14 by bc2000@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the bc2000 group. File :
Re: Bank/Program selection - Casio WK500
2012-04-12 by Royce
It looks like the patches re set up in General Midi form to me. Try http://en.wikipedia.org/wiki/General_MIDI for an explaination. If it is like General Midi
Re: Bank/Program selection - Casio WK500
2012-04-11 by sghookings@tiscali.co.uk
Typically I do this with buttons. There are 4 convenient buttons at bottom right of BCR. And if you pair them, one incr, one decr, (x 2) You can have Bank +
Re: Bank/Program selection - Casio WK500
2012-04-11 by montequi
I just realized I got it backwards. My keyboard has 127 programs (or program groupings), and banks that range from 0-34. Not all programs correspond to each
Bank/Program selection - Casio WK500
2012-04-11 by montequi
Hi! My WK500 is 16-part multi-timbral, but the keyboard interface only allows you to choose sounds on channels 1-3. The rest can only be chosen remotely.
Re: Please Help - Controlling JX-8P parameters using a BCR-2000 (long)
2012-04-10 by twobeelandscape
Adam Thanks for the nice easy guide - I will use this with my AN1X when the time comes. I guess the advatage of installing a prepared template is that you
Re: [bc2000] Re: Please Help - Controlling JX-8P parameters using a BCR-2000 (long)
2012-04-10 by Adam A.
Honestly you don t really need a preset for the JX8P, and I don t recall having to do anything special to get them to play nice. It should seem obvious, but if