Re: New to QTR, 3880 Curves
2013-03-16 by photofarmer69
Tyler, nice to see you on here! And thanks again for pointing me in this direction to begin with. QTR is much easier than I expected it to be. What you re
Messages
Browse messages
Page 103 of 318 · 15852 messages matched
Re: New to QTR, 3880 Curves
2013-03-16 by tboleyyh
hi Graeme, actually if there is a continuos progression of tones without flat spots or reversals with each of the hue curves provided for a different paper
Re: New to QTR, 3880 Curves
2013-03-15 by photofarmer69
Nick, what a kind offer. Thank you. I m getting amazingly nice results using the standard PRBaryta curves, so my interest in trying a curve specifically for
Re: New to QTR, 3880 Curves
2013-03-15 by nmenghardt
Graeme, Glad you re having fun with QTR, it s definitely streets ahead of ABW. There aren t any 3880 curves posted in the files section, but if you re willing
New to QTR, 3880 Curves
2013-03-14 by photofarmer69
Hello, I m new to QTR and have been enjoying it a great deal so far from the little I ve used it. A much much much welcomed improvement over ABW. I m not sure
Unable to access QTR driver via Print Tool
2013-03-13 by iganatz_2000
Hi all, Hoping someone else has encountered this issue and can help. I m on a mac platform - OS 10.6.8. I installed QTR and the Print tool. The
Re: [QuadtoneRIP] Re: Calibration ink pattern page
2013-03-11 by Mark Savoia
I found my mistake, ink slider was at 0%, moved it to 100% and all better now. Thanks. Mark
Re: Calibration ink pattern page
2013-03-11 by rossfmj
Mark It s a bit difficult to tell without maybe some more info. Have you printed this page before with different results on the same settings? What are you
Calibration ink pattern page
2013-03-08 by Mark
All of a sudden it is printing so light I can barely see it. Have it set for 9800 K7. Nozzle checks and printing from Epson driver prints fine. Just ink
Re: [QuadtoneRIP] Re: QTR print tool problem
2013-03-04 by Roy Harrington
Hi Kamil, I ve had some more time to look into this. From what I can tell its a memory allocation failure for images greater than 2 Gigabytes (2**31 -1).
Re: How to setup QUADTONE RIP on a EPSON Stylus Photo 1500W
2013-03-03 by RobertB
If the printer is in proper location,ie Printers and Devices it will be recognized. I ve 2 i400 s and have no confusion between which driver for QTR qnd
Re: How to setup QUADTONE RIP on a EPSON Stylus Photo 1500W
2013-03-03 by rossfmj
QW I have used the installation procedure for the Epson 1400 to set up my 1500w. You need to set up your printer by naming it QUAD1400 and using the QTR
Re: [QuadtoneRIP] Canon PIXMA 9500 MKII and QTR?
2013-03-03 by Ciprian
Aw... that s too bad. :-| Thanks for the update Mike.
Re: [QuadtoneRIP] Canon PIXMA 9500 MKII and QTR?
2013-03-03 by Mike Finley
unlikely - as far as I know all the currently supported printers are Epson ... -- mike finley photography http://www.mikefinley.co.uk
How to setup QUADTONE RIP on a EPSON Stylus Photo 1500W
2013-03-03 by qwertyboy123456
I`m new and I `d like to use QTR for my Epson 1500W, but I don`t see it in the list. How can I proceed? Thanks Q.W.
Canon PIXMA 9500 MKII and QTR?
2013-03-03 by Ciprian
Hello everyone, Does QTR support the 9500 MKII from Canon? Any success stories by any chance? o:-)
Re: QTR print tool problem
2013-03-03 by kamiltresnak
Hi, many thanks to Roy for the private reply. I am attached better images from the real printing tests. Meanwhile, i tested our files with some others
QTR printer driver has quit working.... even after reinstall
2013-03-03 by James Stewart
Folks, I ve had this problem before but can t recall how I fixed it. System: Mac OSX Lion testing QTR printing to an Epson 9600Pro and an Epson R2400. Custom
Re: QTR 21 Step Wedges not linear?
2013-03-03 by James Stewart
Thanks Ross, I was able to get a curve that linearized by doing as you said. I m using a 2 black ink system (Epson 9600) so it may have been throwing me off. I
Re: QTR 21 Step Wedges not linear?
2013-02-28 by rossfmj
Jim I am by no means an expert. I have had a number of these linearisation issues and the only way to get the thing to work is by changing the ink descriptor,
Re: QTR 21 Step Wedges not linear?
2013-02-28 by James Stewart
What is the trick to getting the QTR Linearize Data app to actually linearize the data? I can t get beyond Data not linear and can t be linearized error. I
Re: macro? and micro banding, Epson Stylus Photo 1500w QTR
2013-02-28 by rossfmj
Sidney There is only one path on the 1500 (1430) and that s from the upright holder. I like the idea of the mat, I presume if it s 25mm longer each end,
Re: macro? and micro banding, Epson Stylus Photo 1500w QTR
2013-02-27 by Sidney
Banding within 30mm from top and bottom of paper... This is also a problem with my Epson 2880 printer. My workaround is front feeding my paper - not sure if
Re: [QuadtoneRIP] Re: macro? and micro banding, Epson Stylus Photo 1500w QTR
2013-02-27 by Paul Roark
... I leave 1 inch or 2.5 cm borders top and bottom for the best images. If I get around to making a new 1430 version of UT14, I ll be looking at ways to
New file uploaded to QuadtoneRIP
2013-02-27 by QuadtoneRIP@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the QuadtoneRIP group. File :
Re: macro? and micro banding, Epson Stylus Photo 1500w QTR
2013-02-27 by rossfmj
Berel Thank you very much, I ve switched back to Uni-directional printing and this streaking has gone. I d started using Bi-directional to save time. I don t
Re: Consult needed
2013-02-27 by iganatz_2000
Hi Jon, Thanks for weighing in. Even though it s a turnkey system, I ve always found it helpful to spend time with people who know more than I do. Having an
Re: macro? and micro banding, Epson Stylus Photo 1500w QTR
2013-02-27 by Lutsky, Berel
Sounds like it could be one of several or a combination of issues - first of all - Most of the smaller Epson Printers cannot do a good job of printing the
Re: macro? and micro banding, Epson Stylus Photo 1500w QTR
2013-02-27 by rossfmj
Hmmm. Tried a different batch of paper and it s still happening??
Re: macro? and micro banding, Epson Stylus Photo 1500w QTR
2013-02-27 by rossfmj
I m wondering if this is actually something to do with the paper and not the printing, as it seems to be the same distance in from each edge.
Re: [QuadtoneRIP] Re: macro? and micro banding, Epson Stylus Photo 1500w QTR
2013-02-27 by Mike Finley
Glad that one of the problems is fixed :) I can t help with the longitudinal streaking, except to say the only time I ve seen something that might have been
Re: macro? and micro banding, Epson Stylus Photo 1500w QTR
2013-02-27 by rossfmj
Thanks Mike I ve found the alignment utility and have reset the alignment. I can t see any micro banding now. However the longitudinal streaking is still
Re: [QuadtoneRIP] Re: macro? and micro banding, Epson Stylus Photo 1500w QTR
2013-02-27 by Mike Finley
On the R2400 the nozzle check shows a pattern of short thin lines, and misalignment shows by one of the lines being out of position. I think some of the Epson
Re: macro? and micro banding, Epson Stylus Photo 1500w QTR
2013-02-27 by rossfmj
Mike A nozzle check shows the nozzles to be firing fine. I can t print 30mm at either end of the paper as the banding is very noticeable here. This appears
Re: [QuadtoneRIP] macro? and micro banding, Epson Stylus Photo 1500w QTR
2013-02-26 by Mike Finley
re the micro banding - have you done a nozzle check? I ve found that the QTR driver (on a PC) is much more sensitive to nozzles misfiring (or being slightly
macro? and micro banding, Epson Stylus Photo 1500w QTR
2013-02-26 by rossfmj
I have now managed to linearise UT14 on Hahnemuhle Photo Rag Bright White but am getting micro banding across the print (following the direction of printhead
Re: Problem linearising UT14 with Hahnemuhle Photo Rag Bright White
2013-02-24 by rossfmj
Paul, thanks again for your help. I m still getting not very far and am a bit concerned about using up paper at £1.30 (about$2) a shot ... I can get density
Re: [QuadtoneRIP] Re: Problem linearising UT14 with Hahnemuhle Photo Rag Bright White
2013-02-24 by Paul Roark
... That is low for H. Photo Rag. Is that what your full Calibration Print at 100% showed as the darkest? I just looked at an old 1400 H. Photo Rag QTR
Re: Problem linearising UT14 with Hahnemuhle Photo Rag Bright White
2013-02-23 by rossfmj
Paul After the initial calibration and second calibration prints, I am getting a Dmax of 1.60 from the Black at 25% default ink limit., both C and M came in at
Re: [QuadtoneRIP] Problem linearising UT14 with Hahnemuhle Photo Rag Bright White
2013-02-23 by Paul Roark
If you are using QTR, be sure the C or M ink limit is set low enough that it s maximum density at its ink limit is well below the dmax of the MK. You might
Problem linearising UT14 with Hahnemuhle Photo Rag Bright White
2013-02-23 by rossfmj
I can t get linearised profiles to install for UT14 on Hahnemuhle Photo Rag Bright White. I am getting the message Invalid linearize curve -- not constantly
Re: Consult needed
2013-02-23 by Lutsky, Berel
Much as I might have enjoyed a trip to NYC to share knowledge you do not need a consultant to get up and running with this - Jon is as always 100% correct, you
Re: deletion of old profiles
2013-02-22 by giuliomazzolini@rocketmail.com
Thank you Sidney The problem was that it seems thre are two Libraries, the goog one can be accessed only starting from the hmac hard disk, not apple. Giulio
Re: Consult needed
2013-02-21 by piezobw
Hi Adam, Piezography is turnkey - so you do not need to linearize it or anything. You will just need someone to show you how to fill the carts, install QTR,
Consult needed
2013-02-21 by iganatz_2000
Hi all, I m looking for a power user of QTR and Piezography inks to come in as a consultant for a day and help us set up our new black and white printing
Re: [QuadtoneRIP] QuadtoneRIP ICC profiling tool
2013-02-18 by Roy Harrington
Hi Ben, Since grayscale is just one dimension rather than three, the 21 steps is a lot more data than most of the color target charts. (21*21*21 = 9261 for
QuadtoneRIP ICC profiling tool
2013-02-18 by reallybelgium
Hi, I discovered the ICC profiling tool in QuadtoneRIP. As described, you need to measure a 21-gray target, and produce an ICC profile with these values. (See:
Re: Buy a X Rite 810 Densitometer??
2013-02-18 by reallybelgium
Dear all, Thank you for your interesting replies! Ben Albu
UT14 inkdescriptor files for Epson Premium Glossy Photo Paper
2013-02-17 by rossfmj
As per the auto posting, I have uploaded a couple or three files for UT14 on Epson paper. One for Warm and one for cool. I have also put a file in to use the
New file uploaded to QuadtoneRIP
2013-02-17 by QuadtoneRIP@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the QuadtoneRIP group. File :