Re: 2200 Printing Problem
2005-11-08 by Tom Husband
Would anybody have any idea where to start looking for the problem in this thread? The paper either stops right at the beginning of the print cycle or it goes
Messages
Browse messages
Page 290 of 318 · 15852 messages matched
new to QTR on 10.4 with epson stylus 7600 pro
2005-11-08 by James Frackoviak
I m new to this whol RIP printing thing and I m a little bit confused and frustrated while messing around with QTR. I ve been tyring to get a print out of it
Re: [QuadtoneRIP] Re: 2200 Printing Problem
2005-11-08 by Tom Husband
It happens only when using QTR and hasn t happened at all with the Epson driver. My 2200 is only about 8 months old too. I ve tried the slight pressure trick
Curves for HPR/2100
2005-11-08 by Richard Smallfield
Hi, I ve been using QTR for a while and finally got around to paying for it - sorry for the delay, Roy. I ve been using the supplied EEM curves for both EEM
Re: Sharpness, QTR vs Black-Only
2005-11-08 by djon43
Roy, I m looking at a 10 print of two dumpsters full of bottles and cans, with stickers and grafitti on the outside, trash on the ground etc. With QTR at 1440
Re: 2200 Printing Problem
2005-11-08 by Roy Harrington
The log doesn t say anything because the software doesn t know any of this is happening. I ve also heard that a backing board in the sheet loader may help.
Re: [QuadtoneRIP] Re: 2200 Printing Problem
2005-11-08 by Tom Husband
Thanks Roy. I d appreciate any help at all. I ve been wracking my brain trying to understand the problem. It s intermittent but happening more times than
Re: QTR - Toner reduces Dmax
2005-11-08 by Roy Harrington
It s usually hard to predict what more ink will do to the dMax. Too much ink can reduce dmax -- even if its just black! Tom s suggestion is one good way to
Re: 2200 Printing Problem
2005-11-08 by Roy Harrington
This feeding issue with the 2200 is a stange occurrence. It seems to get worse as a printer ages -- like something is wearing down. I don t remember it
Re: Sharpness, QTR vs Black-Only
2005-11-07 by Roy Harrington
... I don t know exactly what you are seeing, but I wonder if it is just a matter of having gray inks as well as the black ink. In BO the dark black dots
Re: Sharpness, QTR vs Black-Only
2005-11-07 by djon43
Rainer, I ve just made test prints using Epson s sharpen filter, got no improvement, and more sharpen , got sharpness rivaling Black-Only except for
Re: [QuadtoneRIP] Sharpness, QTR vs Black-Only
2005-11-07 by Rainer Taube
... Hallo, i can confirm your observation. I had the same impression comparing QTR and BlackOnly, but i think you cannot directly compare QTR and BlackOnly -
[QuadtoneRIP] 2200 Printing Problem
2005-11-07 by Frank Kolwicz
I get this problem with the Epson driver regardless of paper or thickness. Sometimes I have to repeatedly cancel the printing job in the printer queue, shut
Sharpness, QTR vs Black-Only
2005-11-07 by djon43
I raised this question on the B&W inkjet Group, should do it here as well ... A particular file/image is distinctly sharper with black-only (Epson 2200 driver)
Re: [QuadtoneRIP] 2200 Printing Problem
2005-11-07 by Howard Shaw
... Yes, sorry I meant the paper button. I can t remember if the power button flashes as well. Howard
Re: [QuadtoneRIP] 2200 Printing Problem
2005-11-07 by Tom Husband
Seems it s obviously something to do with the GIMP driver. I see there s a QTRLog.txt file created and wonder if there might be a hint somewhere in that?
Re: [QuadtoneRIP] 2200 Printing Problem
2005-11-07 by Tom Husband
Thanks John. I haven t tried using the rear feeder but have tried to give the paper a little push but it will still jams. When it jams that is, half the
Re: [QuadtoneRIP] 2200 Printing Problem
2005-11-07 by Tom Husband
Thanks Howard. When you say the fault button is that the ones with sheet of paper symbol? When mine jams or when the paper goes all the way through the power
RE: [QuadtoneRIP] 2200 Printing Problem
2005-11-07 by John Moody
Different printer, but that happened on the R200 when one of the inks was assigned, but the description generated no ink. Best regards, John Moody ... From:
RE: [QuadtoneRIP] 2200 Printing Problem
2005-11-07 by John Tunley
Tom, I have often experienced the same problem with an Epson 2100 when using HPR and QTR. Epson papers are less of a problem and, as you say, with the Epson
Re: [QuadtoneRIP] 2200 Printing Problem
2005-11-07 by Howard Shaw
Mine does that too and not only on the calibration test but also on normal images. The red paper light comes on, I reload the paper, press the fault button and
RE: [QuadtoneRIP] Re: Confusion regarding Profiles and QTR
2005-11-07 by Tom Moore
With QTR-RGB Matte, you re soft proofing with a canned icc profile that won t precisely match your paper. That means that you will have to pick options
RE: [QuadtoneRIP] QTR - Toner reduces Dmax
2005-11-06 by Tom Moore
I find it difficult to use the raw/acv curve feature of QTR and usually look for other techniques such as adjusting the gamma or shadow values, or using an
2200 Printing Problem
2005-11-06 by Tom Husband
QTR 2.3.10 Quad2200-UT7 ink XP I m trying to run an ink density calibration but when I print the paper will just travel all the way through the printer without
QTR Toner reduces Dmax
2005-11-06 by rbehr2001
I recently completed a 5 gray ink set for an Epson 2200 with two cool toners. The carbon works great giving a very smooth warm print. The problem arises when I
Re: Confusion regarding Profiles and QTR
2005-11-06 by John Wood
Thanks to both Toms (Moore and Husband). Apart from the fact that I understand what is going on slightly more, I have use advice from both to fine tune my
Re: Quadtone RIP ICC tool....
2005-11-05 by davidkeasey
Thanks, Tom! I had just about figured that out when your reply came through... Since I don t have a densitometer, I guess the profiling issue will have to
RE: [QuadtoneRIP] Quadtone RIP ICC tool....
2005-11-05 by Tom Moore
... Look in the QTR folder in the Windows Program Files folder. There are 2 sources of info. The ICC folder has some older generic profiles and some associated
Quadtone RIP ICC tool....
2005-11-05 by davidkeasey
Another dumb newbie question.... Ok, from browsing the messages, I see that there is a QTRIP tool for generating ICC profiles, to use for soft proofing within
Re: Dumb Newbie question.... importing acv curves from photoshop...
2005-11-05 by davidkeasey
Tom: Many thanks for the quick reply and the tips on how to make it easier. QTR is sooo much easier to use than the non-intuitive RGB curves for printing
Re: Banding with semi-gloss printing
2005-11-04 by koloshor
... Very much so. The gimp print drivers will exhibit microbanding whenever the total ink density (just all all 7 channel curves) exceeds 100%. This is easy to
Re: Lab values not in order error
2005-11-04 by lours51
... out ... 15.33).......... ... In a previous post I exposed this same linearization problem I met. I have tried with different versions of QTR (2.3 & 2.3.1),
Re: Lab values not in order error
2005-11-04 by wwodets
... Yes, it also took me a while to actually read the error message when this first happened. ... This avoidance of Epson papers in quite common and I m
Re: Lab values not in order error
2005-11-04 by jdaalder
Walt Thanks for your very helpful reply. Of course I should have just considered the message literally, but it seems almost too obvious somehow!! The paper is
Re: Lab values not in order error
2005-11-04 by wwodets
JD- The problem you are having is because the LAB values are actually out of order (which QTR Create ICC after versions 2.3.0 will not tolerate). If you look
Lab values not in order error
2005-11-03 by jdaalder
Hi I ve got an Epson 7800 and an Eye One unit and I m trying to use QTR s create ICC program (on Windows XP) to create an ICC profile for the ABW mode. I ve
Re: how much of an advantage ... a general question regards the R2400
2005-11-03 by Steve
Walt, Thanks for clearing that up for me. I will be intalling QTR this weekend, and my Eye-One comes next week. We will see how I fare then. If I need any
Re: how much of an advantage ... a general question regards the R2400
2005-11-03 by wwodets
Steve- You can download the program at: http://www.quadtonerip.com/html/QTRdownload.html On the PC, if you install the program and go to Program Files QTR Eye
RE: [QuadtoneRIP] Re: how much of an advantage ... a general question regards the R2400
2005-11-03 by Tom Moore
Steve You need to download and install QuadtoneRIP. The Eye1 folder is within the QuadtoneRIP installation folder under Program Files (on a PC, of course, on
RE: [QuadtoneRIP] Dumb Newbie question.... importing acv curves from photoshop...
2005-11-03 by Tom Moore
David The curve must be a single channel curve (i.e. from a grayscale file or single channel). In my experience the impact of an acv curve when applied to a
Re: how much of an advantage ... a general question regards the R2400
2005-11-03 by Steve
wwodets, I am looking to do exactly what you are describing below, so I went to the files section of the DigitalBlackandWhiteThePrint group. I found the QTR
RE: [QuadtoneRIP] Dumb Newbie question.... importing acv curves from photoshop...
2005-11-03 by John Moody
I believe I just opened curves adjustment within an rgb file, and saved it. It worked fine in QTR. Best regards, John Moody ... From:
New to WTR and getting dark/black prints
2005-11-03 by jimmyfrack79
I m using a Mac running 10.4.2 with an epson stylus pro 7600 and ultra chrome ink with premium glossy photo paper on a roll. I m having a problem where my
Dumb Newbie question.... importing acv curves from photoshop...
2005-11-03 by davidkeasey
The documentation indicates that I can use an acv curve from Photoshop, but I haven t a good idea how to do this... and the documentation is simply not at all
Re: Banding with semi-gloss printing
2005-11-02 by David Meddings
Quick followup on my own issue: Trying various dithering algorithms with 1440 super or 1440 (both at the better setting) had no effect. Printing at 2880 got
Help with calibration
2005-11-02 by jhaneyzz
I seem to have either forgotten something critical or something changed in a recent version. Currently using QTR 2.3.1 for Mac under OS 10.3.9 to build curves
RE: [QuadtoneRIP] Banding with semi-gloss printing
2005-11-01 by Daniel Staver
... This happens to me when using any one of the lower quality 1440dpi resolutions. Have you tried all the various quality combinations at 1440dpi to see if
Museo Max
2005-11-01 by Timothy Atherton
Just had a chance to test a few sheets of Cranes new Museo Max paper. Fairly unscientific, but: I am finding this a very nice paper. Close to as sharp/crisp as
Re: Banding with semi-gloss printing
2005-11-01 by David Meddings
OK good to know you are back from Shanghai Daniel. Thanks to you and Tom for some suggestions which I ll try. All the best, Dave Meddings
RE: [QuadtoneRIP] ICC and QTR
2005-11-01 by Tom Moore
You cannot use the Epson drivers with QTR. Of course you can print from Photoshop using an ICC profile, but I don t think the ICC profiles created with QTR can