Digitech rotary encoder for data wheel for GSP2101 now at the shop
2012-07-08 by Dieter Waechter
Hi! I have added the Digitech rotary encoder for data wheel for GSP2101 at my shop here:
Messages
Browse messages
Page 5 of 45 · 2224 messages matched
New killer programs added to gsp2101.com
2012-07-07 by rhythmposse
Years of trial and error and I think I got the tone from the first two Boston albums. Master of Pu pets is dead on accurate too. Download them from gsp2101.com
Re: Digipot test fail
2012-06-12 by Scott
... I ve seen an awful lot of digital encodere ( digipots) go bad in recent months. MOstly of stereo gear but one was on a Peavey Pro-fex rack mount
Digipot test fail
2012-06-11 by cmaev2003
The unit is showing this startup error and sends a whine on the outputs. Any ideas or where to get a schematic? + one led is on inside and the -5V rail is
Re: [gsp-2101] Re: 4 cable method
2012-05-25 by Chris Mead
I ve done it but it s been a while. Take a look here or search the board. http://groups.yahoo.com/group/gsp-users/message/8210 ... analog section (i.e.
Scrolling Patches With Control One
2012-05-24 by Nemo Approved
Hay, The battery went dead in my 2101 LTD and of course I lost all my years of tweeked patches. I sent $5 and I m up and rocking again. Before my battery
Re: [gsp-2101] Re: 4 cable method
2012-05-24 by PinkFlydxx@AOL.com
It is correct that this configuration will completely take out the 2101 s analog section (i.e. compression, distortion, etc), but will allow you to use all
Re: 4 cable method
2012-05-24 by Rickenbacker
Got it... Thanks .. I was using both EFX send and return on the 2101, This doesn t seem like a 4 cabke method when i am using 3 cables but it works.. This
Re: [gsp-2101] Re: 4 cable method
2012-05-24 by Chris Mead
I ll take a shot at it.... The following will bypass the 2101 s pre-amp and analog section and will lower the noise floor. Just the digital effects will be
Re: [gsp-2101] Re: 4 cable method
2012-05-24 by Rick johnson
OK i tried again and failed..I am trying it through a fender deville..Its has a effects loop and also 2 inputs on the top.. all i got was a big hum, so i
Re: [gsp-2101] Re: 4 cable method
2012-05-23 by Rick
the picture confuses me, because , there is an input on the amp for the guitar, but the input beside it should be an output, because it has a wire going too
Re: [gsp-2101] Re: 4 cable method
2012-05-23 by Marko Menart
Page 88, the last sentence: if your Amp head doesn’t have a second input, a -Y- cable will work just as well . Best regards, Marko
Re: [gsp-2101] Re: 4 cable method
2012-05-23 by Rick
I appreciate all the help, this machine is way above me, but i will try it again, the picture of the set up on page 89, everything i get, except for the extra
Re: 4 cable method
2012-05-23 by vince.a@verizon.net
Send out to the efx, return into from the efx and within the program...see page 89 of the manual, they use the example of a head with effects, but it is the
4 cable method
2012-05-23 by Rickenbacker
How do you hook this up too the effects loop and do you have to do something to the 2101 to turn on the effects, i cannot figure it out in the manual..
Re: [gsp-2101] How to Adjust the volume
2012-04-26 by Rick johnson
HI I did that today, went through each program to 100, and set them to 0 db.. from there i can decide what to set them too, too bad Digitech would not just
Re: [gsp-2101] How to Adjust the volume
2012-04-26 by chris.pelayo@sbcglobal.net
Yeah while the 2101 is a massively powerful machine it does seem that something as basic as a preset level parameter was not built in. No worries though you ll
Re: How to Adjust the volume
2012-04-26 by Rickenbacker
Thanks for the manuals Chris, i have alot of reading material now, i probably wont go to deep into this unit for now, but would like to try my own program
Re: How to Adjust the volume
2012-04-26 by Chris Mead
Rich, Each program has a master volume. Set it so you have gain unity using the bypass switch. Check your email for the manuals. ~Chris Rich, Each program
How to Adjust the volume
2012-04-26 by Rickenbacker
I am a newbie too the 2101 without a manual, one thing i notice is some programs are much louder then others. How do i adjust the volume on a program and save
Digitech Footcontroller Cable and Otput potentiometers are available again
2012-03-31 by Dieter Waechter
Hi! For all who asked me: http://www.nocrotec.com/shop/index.php/language/en/cat/c2_Digitech-Teile.html All the best Dieter
RE: [gsp-2101] No Effects
2012-01-16 by M M
I just looked at a few patches on mine and they were set to bypass. I have guitar in the front input and XLR s out to the mixer right now and sound comes out
RE: [gsp-2101] No Effects
2012-01-16 by Charlie Watson
I just tried the hard re I just did the hard reset, still no sound with the bypass off. Took the cover off & tested the voltage between pins 16 & 32 on the u74
RE: [gsp-2101] No Effects
2012-01-16 by M M
Normally the bypass is off. Try a reset if you have no data you are concerned about. To: gsp-2101@yahoogroups.com From: charliebaba51@hotmail.com Date: Mon, 16
Re: [gsp-2101] No Effects
2012-01-16 by chris.pelayo@sbcglobal.net
Charlie, Ok so it s not the Fx Loop settings. A few questions: 1. Does this happen with EVERY patch? 2. Even the factory presets? 3. Have you tried a hard
RE: [gsp-2101] No Effects [1 Attachment]
2012-01-16 by Charlie Watson
Must not have been the FX loop settings. I tried all 3, bypass, summed & no sum.When the gsp is working correctly is the bypass switched on or off ? Currently
RE: [gsp-2101] No Effects
2012-01-15 by Charlie Watson
Thanks Chris. To: gsp-2101@yahoogroups.com From: chris.pelayo@sbcglobal.net Date: Sun, 15 Jan 2012 18:25:05 +0000 Subject: Re: [gsp-2101] No Effects Clicked
Re: [gsp-2101] No Effects
2012-01-15 by chris.pelayo@sbcglobal.net
Clicked send prematurely on previous post.... I attached the 2101 manual in my previous post, read the section on effects loop settings. I think you ll find
Re: [gsp-2101] No Effects
2012-01-15 by chris.pelayo@sbcglobal.net
It s probably your effects loop settings. _ Sent from Chris R. Pelayo s Blackberry ... From: charlie37752 Sender:
No Effects
2012-01-15 by charlie37752
I have a GSP-2101 Limited Edition. When I bought it (used) it worked fine. However, now I can t get the effects to work. First I couldn t get any sound at all
Re: Upgraded to 20MHz, now can't assign programs to footswitches
2011-12-03 by softwareproductmanager
Dieter suggested resetting doing a factory reset, again. This time, I decided to not only reset the Programs, but also the Utility/MIDI settings. Now, it
Upgraded to 20MHz, now can't assign programs to footswitches
2011-12-03 by softwareproductmanager
While I m waiting to hear back from Dieter, I wonder if any of you have run into this. I have the faster crystal and different capacitors installed. The Artist
George Harrison's Badge
2011-12-02 by gdmpearson
Hey guys: I m trying to create a program that sounds like George Harrison s lead on Badge. I would like to base it on a Factory Algorithm rather than a User
Re: [gsp-2101] I have a 2101 but a 21 Legend footcontroller
2011-09-13 by Rish
I have a 2101 pedal board I would be willing to sell, I picked it up for parts but have never needed it scavenge from it. It s used and a bit scratched up but
Re: [gsp-2101] I have a 2101 but a 21 Legend footcontroller
2011-09-13 by chris.pelayo@sbcglobal.net
I don t believe it can be done. The 21 was a much simpler pedal board and processor. I would think it would be like trying to use a Smart Car to pull a 20 foot
I have a 2101 but a 21 Legend footcontroller
2011-09-13 by Scott
Is there some way to modify a cable to make them work together?? I m a professional tech so, wiring and the like doesnt scare me Thanks
RE: [gsp-2101] Re: Controll One Issue
2011-08-22 by M M
You can get 5 pin DINs for computer use that likely have all 5 connected. To: gsp-2101@yahoogroups.com From: iwannabeinapunkband@yahoo.com Date: Mon, 22 Aug
RE: [gsp-2101] Controll One Issue
2011-08-22 by M M
I knew it had something to do with 2 extra pins. Well I ve never owned a Control 1. Thanks for the correction. To: gsp-2101@yahoogroups.com From:
Re: [gsp-2101] Re: Controll One Issue
2011-08-22 by chris.pelayo@sbcglobal.net
I actually got a bona fide 5 pin from GC, they have them so... - Sent from Chris R. Pelayo s Blackberry ... From: Roundboy
Re: Controll One Issue
2011-08-22 by Roundboy
Thanks for all of the help to everyone! The only one I have been able to find that says anything about all 5 being connected is the HOSA Midi Cable:
Re: [gsp-2101] Controll One Issue
2011-08-22 by chris.pelayo@sbcglobal.net
Like M M said you definitely need to have the needed and fully functioning DIN cable. I say fully functioning because many MIDI capable electronic devices
Re: [gsp-2101] Controll One Issue
2011-08-22 by Graham Pearson
The Control One has a standard 5-pin female DIN socket. So does its counterpart socket on the back of the GSP-2101. Many MIDI cables have only 3 wires,
RE: [gsp-2101] Controll One Issue
2011-08-22 by M M
Doesn t the Control 1 require a 7 pin DIN? And make sure it s connected to the right socket or damage could result. To: gsp-2101@yahoogroups.com From:
Controll One Issue
2011-08-22 by Roundboy
I have tried two different cables and not sure whate the problem might be. The pedals 1, 2, 6, and 7 all seem to have the same problem. When I press them they
RE: [gsp-2101] Question about upgrade
2011-07-22 by M M
Graham, how much is the MIDIWizard software? I might buy it for this feature alone. As a severe 2101 addict since the early 1990 s I should probably upgrade to
Re: [gsp-2101] Question about upgrade
2011-07-22 by Graham Pearson
CORRECT: The format of SysEx dumps changed between EPROM versions prior to Version 3.00.00 and Version 3.00.00. MIDIWizard is the only software that
RE: [gsp-2101] Question about upgrade
2011-07-22 by M M
You need to be careful when changing the software though. Unlike changing a battery, I ve heard that after a software/firmware upgrade that your midi dump
Re: [gsp-2101] Question about upgrade
2011-07-22 by C Mead
I ve done it. It s not a big deal but you will want to backup all your user programs first because you will lose them. This is more of a challenge than
Question about upgrade
2011-07-21 by Neil Rego
Hi, I have a GSP 2101 Preamp/processor S-Disc 1.06.06 September 94 model. I would like to know if I want to do an upgrade to 3.00.00, would the chip be
Re: [gsp-2101] Can I buy a 2101 power transformer??
2011-07-19 by krazydog
hehe I always left that middle one off!! ... From: M M To: gsp-2101@yahoogroups.com Sent: Tuesday, July 19, 2011 2:28 AM Subject: RE: [gsp-2101] Can I buy a