Philips-Apps ??
2005-02-21 by rhpascaldodo
Hi friends, because there was no response of my last question, here is a new one. In some publications the LPC213x series are introduced as the new standard
Messages
Browse messages
Page 215 of 329 · 16407 messages matched
Timer 1 Interrupt problem in LPC2106
2005-02-21 by mannem_sri
Hi, I am trying to generate an interrupt using Timer1 in LPC2106. I put 0xff in match register. The timer is incrementing and restting whenever it matches the
Re: Some Questions: IDE for GCC
2005-02-21 by aj_erasmus
... [Suggestions snipped] I would suggest using Dev-C++. This comes setup to work with mingw, and there is a howto available to set it up to work with
Re: [lpc2000] Re: What hardware is needed to use the Philips Flash Utility?
2005-02-21 by santosh jha
hi I have used the same board for one of my project. put jumper on BSL (2 pin berg stick on board) and then sw on the power and use phillips flash utility to
Problem with newlib-lpc_rel_4
2005-02-21 by aj_erasmus
Hi, I have a strange problem when using the library newlib-lpc_rel_4. I am using the gcc downloaded from http://www.gnuarm.org. The problem is the same whether
Re: [lpc2000] Target options on Insight
2005-02-21 by Bruce Paterson
... I m afraid I don t understand the above statements. Neither the first or the 2nd columns are in order. That is, even if we jumped around in the C code
RE: [lpc2000] Re: EMI Testing
2005-02-21 by Joe Hlebasko
Unless you have the RF clea area as mention below it is not worth to buy the antennas. You should have a B-Field probe. These are good for sniffing out
Re: EMI Testing
2005-02-20 by embeddedjanitor
... does ... This is not the sort of thing you should expect to answer on a group like this. You ll need various antennas and probes depending on what you re
Re: GCC runing optomization!
2005-02-20 by embeddedjanitor
... I have had no problems using various versions of gcc, at various optimisation levels. As others have said,check your volatile declaraions.
Re: Some Questions: IDE for GCC
2005-02-20 by ntfreak2000
... Visual Studio is not to hard to use but you have to maintain the makefile yourself - external makefile. Eclipse is ok but a huge download and a bit of an
Re: Some Questions: IDE for GCC
2005-02-20 by dsidlauskas1
You can get a very nice free source code editor at http://www.crimsoneditor.com/ It can be configured to call external programs such as a compiler or linker,
Re: [lpc2000] Some Questions: IDE for GCC
2005-02-20 by sig5534@hotmail.com
Yeah I use UltraEdit32 right now for my IDE with GCC. Works great. I love it. Output window, function keys to run compiler. Highly recommended. Chris. ...
Re: [lpc2000] Re: CAN controller 2 on the LPC2129
2005-02-19 by Robert Wood
Hi Daniella, I m using the 2294 and have used two of the four CAN modules without any problem. Here s the code I have used to set it up, you should hopefully
Re: CAN controller 2 on the LPC2129
2005-02-19 by dietmar_wengler
Hi Daniela, A few weeks ago, I tried to evaluate the CAN Interface without the demo files, only with Philips User Manual, and it ended in a big chaos. For this
Re: [lpc2000] Some Questions: IDE for GCC
2005-02-19 by Jens Hildebrandt
... I have used UltraEdit+GCC for LPC20xx development in the past. Not much comfort like in VS but at least syntax highlighting and some pretty good text
Some Questions: IDE for GCC
2005-02-19 by unity0724
Hi, Some Questions: My Arm GCC for LPC21xx is not very well setup on my PC, and thinking of... a) UltraEdit+GCC Had anybody tried using UltraEdit32 as simple
Re: [lpc2000] GCC runing optomization!
2005-02-19 by jane highland
Gus, The rule with optimisation e.g. -O3 : If a function calls a function outside of the current C module, the function will definately be called. If a
Re: [lpc2000] GCC runing optomization!
2005-02-18 by Bryce Schober
I m not using 3.4.2, but in general: We use extensive optimization in all of our products (we couldn t live without it). Without optimization gcc basically
Re: LPC2139 ????????????
2005-02-18 by Rick Collins
If you are looking for the TMS470R1A256, then that is the part number you can search on. If you just use TMS470R1A you will get both the 128 and the 256 part.
Re: [lpc2000] Re: LPC2139 ????????????
2005-02-18 by Robert Adsett
... 296-17627-ND Robert Freedom has no meaning of itself. There are always restrictions, be they legal, genetic, or physical. If you don t believe me,
Re: LPC2139 ????????????
2005-02-18 by Gus
what is the digikey part number? I can t find them! Gus ... the 48 ... find ... have ... that ... out ... number) ... samples ... ordered
RE: [lpc2000] Re: LPC2139 ????????????
2005-02-18 by Greg Deuerling
... I just purchased 100 LPC2194 s from AvNet for $7.50 each. I d say at qnt. 1000 they would be well below $6. Get a quote from AvNet and see what they can
Re: LPC2139 ????????????
2005-02-18 by Rick Collins
Do you really expect the LPC CAN parts to be less than $5? The TMS470R1A64 has CAN and is only $5 @1k and the A128 is only $7 at Digikey and will likely be
Re: LPC2139 ????????????
2005-02-18 by geno_24@yahoo.com
The LPC2119, 2129 and 2194 already have CAN and they look to be much higher performance and lower cost than the TI automotive parts that Rick mentioned. I ve
Re: LPC2139 ????????????
2005-02-18 by Rick Collins
... The TI parts have CAN, TMS470R1A64/128/256. I have some samples of the A256 part in my hand. The A128 and A256 parts can be ordered on Digikey from
GCC runing optomization!
2005-02-18 by Gus
Hello, Anyone is using GCC compiler version 3.4.2 WITH optomization? When I enable optomization, my applicatin acts funny! I am not sure why. Gus
Re: LPC210x Temperature Range for Operation
2005-02-18 by geno_24@yahoo.com
Hi Markus, The LPC2104, 2105 and 2106 are still only 0 - 70 C. If you need -40 to +85C, you ll need to go to the 64-pin parts, such as the LPC2114, LPC2132,
Re: IAR Flash Programming
2005-02-18 by Leighton Rowe
Thanks for the info. Does the flash programmer on EWARM 4.20A have the ability to erase flash? I m not sure that the programmer on the version I m currently
Re: [lpc2000] Target options on Insight
2005-02-18 by Robert Adsett
... That fit s with what I ve seen. GCC is more prone to re-ordering than other compilers I ve used. Several things to note on the above sequence - The
LPC2139 ????????????
2005-02-18 by rhpascaldodo
Hi PhilipsApps where is the LPC2139 (~2138 with CAN) ? when can we expect to see some chips and the datasheet ? regards Rolf
Uploaded LPC Flash Programming Routines
2005-02-18 by Bill Knight
I just uploaded a set of LPC flash programming routines to the files area on Yahoo. They were written for gcc and support both ARM and Thumb modes of
New file uploaded to lpc2000
2005-02-18 by lpc2000@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the lpc2000 group. File :
Re: Profibus
2005-02-18 by juaco5000
... Profichip has a nice IC, for slave applications VPC3+B PROFIBUS-DP/-V1/-V2 Slave ASIC Joaquin Fernandez
Re: LPC2138 DA convert speed?
2005-02-18 by foyyyof
... that ... I got it..thanks for your reply ! Karl.
Re: LPC2138 DA convert speed?
2005-02-18 by Karl Olsen
... To software, the DAC appears as a read/write register, and you can just write new values to it as fast as to any other peripheral register on the VPB bus,
LPC2138 DA convert speed?
2005-02-18 by foyyyof
I can t got any infor from the datasheets.
Re: [lpc2000] Target options on Insight
2005-02-18 by Bruce Paterson
... Here s an example with just pure assembly. Insight console screen shows this for library function _puts_r. Note how it isn t sequential ! - 0x4224
Re: Profibus
2005-02-18 by Richard
Profibus offers training classes (which I will be attending). See: http://www.profibus.com/profinet.html Also, let me know what you find, I also will be
EMI Testing
2005-02-17 by fl429
I know this may not be the right group for this question. But it does seems to have the right crowd, right ? We have a HP8563E Spectrum Analyzer. I want to use
Re: [lpc2000] PWM
2005-02-17 by Jack Xu
Hi Rolf, I solved the problem by adding: PWM0_TC=0x0 after starting TC. Thank you for your help. Jack. ... __________________________________________________
Profibus
2005-02-17 by Micron Engineering
I am searching for a Profibus solution for ARM (hw and firmware). Is there any solution ready? Massimo Manca, Micron Engineering -- No virus found in this
IAR Flash Programming
2005-02-17 by lp2000c
After IAR released EWARM version 4.20A, one of my colleagues discovered a bug in their flash programming for the LPC chips. It will not let you program the
LPC210x Temperature Range for Operation
2005-02-17 by Markus Meng
Hi all, I just wonder if the specs for the temperature range are still consumer only 0..70 degree celcius. Is there a version for the -40 ... + 85 range?
Re: [lpc2000] PWM
2005-02-17 by lpc_bavaria
... Hi Jack, ... 0x5400 would be right here (you don t use PWM5) ... Please set the value in MR0 *BEFORE* you enable the PWM (which you did in the previous
Re: [lpc2000] Re: LPC2106 fails to start with fast power slew rate???
2005-02-17 by Wayne Radochonski
Tsvetan Thanks for the insight and yes, these are rev B parts on my board. I will search the list for latch up . Thanks again, Wayne ... to ... check the
Re: LPC2138 with P0.11 not working
2005-02-17 by nmitech
Thanks Robert, That was it! Sorry, I did not pay attention to the I2C shared signal. ... CPU. ... restrictions, ... to
Re: LPC2106 fails to start with fast power slew rate???
2005-02-17 by tsvetanusunov
... to ... check the LPC2106 revision, if it s REV.B search the messages for the latchup problem with LPC2106 Best regards Tsvetan ... PCB prototypes for $26
Re: [lpc2000] LPC2106 fails to start with fast power slew rate???
2005-02-17 by Wayne Radochonski
Kris Yes, all of those things you mentioned have been checked. They work fine with the certain lower output current power supplies. The only thing that looks
Re: [lpc2000] LPC2106 fails to start with fast power slew rate???
2005-02-17 by microbit
Hi Wayne, ... If RESET is really held low for that time, then the slew rate shouldn t matter AFAIK. Are you sure nRST and nTRST are sound ? Boot pin ? Held
LPC2106 fails to start with fast power slew rate???
2005-02-17 by dharmaBum
I m working on a design that uses a LPC2106, but the design will be migrating to the LPC2138 on the next revision of the PCB. The LPC2106 seems to have