Re:I think I want to go back to dye ink.
2007-10-24 by Barrett Benton
Jens: I think I know what you mean here. I d actually gone the route of third-party quad setup (Lyson Quad Black Neutral with their Darkroom Range Glossy
Messages
Browse messages
Page 431 of 2186 · 109257 messages matched
Re: MIS ink question
2007-10-24 by scott_now_coming
Frank, Are you printing through QuadToneRip (QTR)? Paul set up the R800/1800 to print with 3 matte black carts installed in the printer. Paul chose the MK, PK,
RE: [Digital BW] CanonIPF 6100
2007-10-24 by George Pappas
I just took delivery of its little brother, the 5100. So far it is very sweet. I will post some more information after a few weeks of use. _____ From:
[Digital BW] Re: I think I want to go back to dye ink.
2007-10-24 by i_3d_c
Well, I m going to give it a shot. If the black is horrible, I ll put the Epson dye back in the black slot and use the lyson greys. I *know* I like the Epson
MIS ink question
2007-10-24 by Frank Jay
hello I bought a set of MIS inks specifically for my new R1800. The directions on the website say these inks are to be used on matte papers. I bought a pack
Re: I think I want to go back to dye ink.
2007-10-24 by Frank Jay
I just purchased an R1800 and a set of three MIS inks for it. I wish I read posts like this before I made the purchases. I read all I could by knowledgeable
Re: [Digital BW] hampering paper feed of Epson 2100
2007-10-24 by Joost Horsten
Ken, Thanks for the pointer. I ll give it try tonight. Joost ... exhibition ... tries ... sheets ... photo ... but The
CanonIPF 6100
2007-10-24 by stanleybutterfass
Any comments about the CanonIPF 6100?
Re: [Digital BW] Re: 3800 Ticking Noise
2007-10-24 by Carl Schofield
Are you sure that the printer head is not hitting the edge of the paper? Try increasing the platen gap and see if the ticking goes away.
Re: 3800 Ticking Noise
2007-10-24 by pglombick
... EXCEPT ... makes a ... sweep ... Jeff: I have this exact problem, except on a used R2200 I bought for K7 inks. It drives me crazy when I am in the room. I
Re: [Digital BW] I think I want to go back to dye ink.
2007-10-24 by babelfish
I know what you mean. I recently ran across some prints that we made with dye inks on H. German etching and photo rag papers that are stunning in comparison to
Re: [Digital BW] 3800 Ticking Noise
2007-10-24 by Brian Ellis
Haven t had that problem. Mine makes the usual noises when it s first gearing up to print after being turned off but while it s printing I don t hear anything
Re: 3800 Ticking Noise
2007-10-24 by Vincent Orlando
I can t hear my 3800 when it is printing. Have to look at to see if it is printing. Vinny www.wulfsden.com
Re: [Digital BW] Re: I think I want to go back to dye ink.
2007-10-24 by Carl Schofield
Unless they have reformulated the black ink, be prepared for purple prints under incandescent lighting and green/blue in daylight. I think IJC developed some
Re: I think I want to go back to dye ink.
2007-10-24 by i_3d_c
I think I m going to give the Lyson Daylight Darkroom inks a try. Thanks.
Re: [Digital BW] I think I want to go back to dye ink.
2007-10-24 by i_3d_c
Yes, this is what I ve tried and while it looks fine viewed by itself it pales next to the Epson dye black. Actually, I think I am going to give the Lyson a
Re: I think I want to go back to dye ink.
2007-10-24 by i_3d_c
I just really like the look of deep blacks on a matte paper -- not fond of glossy or semi-glossy ... Becker ... Matte ... little ... great for ... And was ...
Re: [Digital BW] Re: Creating grain
2007-10-24 by Harry Saddler
Remember that at the advent of photography, everyone was trying to make photographs look like paintings until a few brave, forward- looking souls embraced the
Re: [Digital BW] Re: 3800 Ticking Noise
2007-10-24 by atodzia@cox.net
Yes. Mine does the same thing. My first one didn t but had other problems. I have leaned to ignore the TICKING sound, but it drove me crazy at first.
Re: 3800 Ticking Noise
2007-10-24 by scott_now_coming
... a ... sweep ... Jeff, Turn the music up a little louder. ; )
3800 Ticking Noise
2007-10-24 by Jeff Magidson
I just set up a new Epson pro 3800 printer and it works great EXCEPT it makes this somewhat annoying TICK sound each time the head makes a pass. Kind of like
Re: [Digital BW] I think I want to go back to dye ink.
2007-10-24 by robert49brake
... I would highly agree. I was following Paul s development of the 3MK approach with the R1800 when I decided to give it a try on an R220 I keep around for
Re: I think I want to go back to dye ink.
2007-10-24 by alistair_owens
... I just wish there were a ... I seem to recall that the Lyson Quad Tone inks were dye based. Lyson have been through ownership changes and I am not sure
Re: [Digital BW] I think I want to go back to dye ink.
2007-10-23 by Charles Becker
www.oddparts.com is listing dye based inks for R800 and it s the same for the 1800. i_3d_c wrote: I m using Eboni black right now,
Re: [Digital BW] I think I want to go back to dye ink.
2007-10-23 by Carl Schofield
I think you might be surprised at the dmax and pop of the Eboni 3- MK prints from your 1800. Since you already have the right printer, ink, and QTR why not
Re: [Digital BW] I think I want to go back to dye ink.
2007-10-23 by Adam Maas
If you re looking for high DMax, why not look at a PK setup on a semi-glossy paper, that should net you higher DMax than a matte paper and MK ink like Eboni.
Re: [Digital BW] I think I want to go back to dye ink.
2007-10-23 by i_3d_c
I m using Eboni black right now, which this set also uses. So it s hard to imaging that switching would give me significantly greater d-max. I ve done a lot of
Re: I think I want to go back to dye ink.
2007-10-23 by i_3d_c
Actually, I have gotten very good results with glossy and pearl papers. Trouble is, it s just not the look I m after. When I look at my prints made on Han Fine
Re: [Digital BW] I think I want to go back to dye ink.
2007-10-23 by Charles Becker
Go to www.inksupply.com and then B&W printing and the UTBO (Ultratone Black Only) inks are made for the Epson R1800. Excellent results, better then other B&W
Re: [Digital BW] hampering paper feed of Epson 2100
2007-10-23 by kenc
Your problem s likely that the rollers are dirty or have a layer of whatever comes off fine art matte papers on them. There are various ways of cleaning them,
hampering paper feed of Epson 2100
2007-10-23 by Joost Horsten
Tonight I was in the midst of a series of test prints for an exhibition when suddenly the paper feed of my Epson 2100 hampered: printer tries to load a sheet
Re: I think I want to go back to dye ink.
2007-10-23 by JensGerbitz
Hi there, I know what you mean about printing on matte papers with pigment inks... I m still trying to get decent dmax and not having much luck without losing
I think I want to go back to dye ink.
2007-10-23 by i_3d_c
My first inkjet printer was the Epson 1270. I scanned some of my old 4x5 negs and printed them on Archival Matte paper. I fell completely in love with the
Re:Creating grain
2007-10-23 by sinwen
Another suggestion if I may..... scan a grainy negative and overlay in PS ....or ..... snap directly with film :) [Non-text portions of this message have been
Re: Any usable mounting sprays?
2007-10-23 by scott_now_coming
Not a spray, but I ve used this before with the supplied squeege: http://www.artsuppliesonline.com/catalog.cfm?cata_id=6730 Scott
Re: Creating grain
2007-10-23 by Myron Gochnauer
I ll second Eric s suggestion of RealGrain. It is the best I ve found (or at least equal to the best). Aside from allowing control of color/monochrome grain
Re: [Digital BW] R220 printer
2007-10-23 by ann clancy
sorry, i listed it in the subject title Epson R220. ann CorrPro96@aol.com wrote: In a message dated 10/22/2007 9:54:30 P.M. Eastern Daylight Time,
Re: [Digital BW] R220 printer
2007-10-23 by CorrPro96@aol.com
In a message dated 10/22/2007 9:54:30 P.M. Eastern Daylight Time, jaclancy1937@yahoo.com writes: My students were printing away when i had to change a few ink
R220 printer
2007-10-23 by ann clancy
I realize this list is for black and white printing, but i had an issue tonight with a printer at school and really don t know who else to ask, so please have
RE: [Digital BW] Re: Any usable mounting sprays?
2007-10-22 by E Neilsen
Tyler, In my earlier days as an assistant in a frame shop, we used a roll on adhesive that was great for use with damaged posters, prints, etc. We slightly
RE: [Digital BW] Re: Paul's 4Ks inkset
2007-10-22 by Paul Roark
A PKN will kick the dmax up higher than the standard PK from MIS. I have made new ones for the modern printers (the 260 RC-PKN and PKC [cooler]). However, I
Re: Paul's 4Ks inkset
2007-10-22 by met.graphix
Thx for the info Paul. Reason I asked is because both on a 2200 and a 7600 with all glossy papers I tried this PK seems to give me the best dmax when printing
Re: Any usable mounting sprays?
2007-10-22 by john dean
I ve used the 3M Spray Ment cans and they seem to hold well, but like you I certainly wouldn t trust them for long term storage on valuable prints. There is no
RE: [Digital BW] Paul's 4Ks inkset
2007-10-22 by Paul Roark
Hi Dario, ... It depends on the printer and purposes. The K4 PK is a lower load PK optimized for the newer printers -- from about the R220 on. In those it ll
Paul's 4Ks inkset
2007-10-22 by met.graphix
Paul, In the original configuration of this inkset most of the inks are K4 inks. Only the PK is from the MIS PRO inkset (MIS MP-PK)Any reason why the PK is not
Re: [Digital BW] Creating grain
2007-10-22 by Ender100@aol.com
An interesting trick to adding grain that I came up with years ago and I like the effect: 1. Create a new layer on top of the image and in the add layer
Re: Creating grain
2007-10-22 by Gary Weaver
Hi pglombick, I ve been playing with noise the past few months. I m mostly trying to get film to look like film, but I started out by seeing what was possible
Any usable mounting sprays?
2007-10-22 by Tyler Boley
I ve just been asked about this, and since I never used adhesives on the coated art papers I thought I d pass the question on. Any luck with any of them? No
Re: Creating grain
2007-10-22 by johncjmd
I am not denigrating any of these recommended plugin products, but would like to share my own experience. After buying various plugins over the years, I
Re: Creating grain
2007-10-22 by the_des_bois
Eric, Thanks I ll sure take a look at Imagenomic before upgrading to AS Exp. 2. :) Denis ... having ... urban ... noise ... also ... the ... does one