Yahoo Groups archive
Messages
Page 340 of 564 · 28179 messages matched
2006-09-15 by hardware@doepfer.de
Provided that the additional +5V are OK the module has probably a fault. If you have another module that requires +5V too (A-190 or A-113) you may try if the +5V are OK. Best wishes Dieter Doepfer > -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com > [mailto:D
2006-09-15 by William Soraparu
No matter what I do on the A-191...the three lower leds stay lit. I cannot change between the Sheppard and Midi to CV. Mahalo WIlliam hardware@doepfer.de wrote: William, you find my answers below > All, question on tha A-191. > > Prior to the installation of the A-191, I did plug
2006-09-15 by William Soraparu
All three LEDs stay on permanent. All the other modules are working fine off of that same bus board. hardware@doepfer.de wrote: William, you find my answers below > All, question on tha A-191. > > Prior to the installation of the A-191, I did plug into the > Doepfer bus the A100-
2006-09-14 by James Husted
I tried to do this again last night and it worked great. I guess the last time was a mistake or bad download. Illustrator CS2 worked fine - the typical wierdness with fonts going to the Mac format but still more than useful to me as a layout planner. I think last time I removed t
2006-09-14 by James Husted
Yes - it worked. Sorry, no other formats needed. James Husted James.husted@mac.com http://homepage.mac.com/ersatzplanet/ "Welcome to the first day of the rest of your money." On Sep 13, 2006, at 9:53 PM, laryn91 wrote: > After reading Dieter's reply yesterday, I tried and read th
2006-09-14 by hardware@doepfer.de
William, you find my answers below > All, question on tha A-191. > > Prior to the installation of the A-191, I did plug into the > Doepfer bus the A100-AD5 > 5V Low-Cost Adapter. I plugged it in correctly :-)!!!! > > Now, with the system powered up, and the A-191 plugged in > cor
2006-09-14 by William Soraparu
All, question on tha A-191. Prior to the installation of the A-191, I did plug into the Doepfer bus the A100-AD5 5V Low-Cost Adapter. I plugged it in correctly :-)!!!! Now, with the system powered up, and the A-191 plugged in correctly, should the lower 3 LEDs be on steady? Manua
2006-09-14 by hardware@doepfer.de
For prototypes we use a standard laserprinter (HP) to print the front panel layout to a self adhesive transparent foil available in office supply shops. Then the foil is trimmed to the right size and glued to the front panel. The required holes in the foil (for potentiometers, so
2006-09-14 by Julian
just pm'd you about the screen printing would anyone else be interested? it isnt cheap, but its somthing ive been looking into - if i can get enough pannels on the one screen it *may* be feasible. as for lasertran - its a specialy coated paper that you print onto with an inkjet (
2006-09-14 by IZAM
cheers for info julian and also the link dieter .Can anyone recoemmend a screen printer in uk or europe ? I meant to also ask how does lasertran works ? Julian wrote: Allan Hall did a lot of this kind of stuff (you still about allan? ; ) But heres a few comments - If youre keepin
2006-09-14 by Julian
> But to speak the truth I don't have the time to find it out. I > think offering all A-100 front panels as a Corel Draw file is much more > than > other companies do ... Dieter, Ive been very impressed (not to mention almost a little supprised : ) with the help youve given me in
2006-09-14 by hardware@doepfer.de
James, we've tried this earlier but Corel Draw is hanging up during the Illustrator export. I've no idea what's wrong. Maybe it's because of the file size and one has to cut the file into several small parts (e.g. one frontpanel per file only). But to speak the truth I don't have
2006-09-14 by laryn91
After reading Dieter's reply yesterday, I tried and read the CDR file without any problems using Illustrator CS2. Maybe try again? --- In Doepfer_a100@yahoogroups.com, James Husted wrote: > > Dieter- > I was wondering if it would be possible to offer the files as Adobe > Illustra
2006-09-14 by James Husted
Dieter- I was wondering if it would be possible to offer the files as Adobe Illustrator files also. I used to own Corel Draw and remember it could export in many other formats. Illustrator is more of a standard and can be imported into more vector drawing programs than Corel can.
2006-09-13 by nicholas_kent
> amnesia wrote: > Hi all > > I just bought my first Doepfers this week....I didn't want to ask for > sounding stupid, but with the A149 can someone give me an example of a > patch to use for this what is CVDin etc? oh and again adsrs i understand > on my Jupiter 8 but can someon
2006-09-13 by David Salter
Ingo, Re voted. Thanks David David Salter Senior Consultant PSG Reuters Messaging: david.salter.reuters.com@reuters.net (t) +44 (0)20 7542 2402 | (m) 07990562402 | (f) 52699 Get the latest news at Reuters.com ________________________________ From: Doepfer_a100@yahoogroups.com [ma
2006-09-13 by hardware@doepfer.de
Thank's for the poll. I hove some comments concerning the prices of the different options: The rotary switches used in the A-110 and A-111 are very expensive parts. Consequently: 1. Three toggle switches for octave selection (1, 2, 4 octaves) would be about the same as the rotary
2006-09-13 by vliesgaard
I understand, rather obvious at a second glance. Thanks for the replies.
2006-09-13 by selfoscillate
thanks for clearing out on the price differences, dieter. i have edited the poll text to reflect that, but i didn't know that this would delete the already given votes. i'm sorry about that, but there were only three votes given anyway, so i hope that it was not a too bad mistake
2006-09-13 by selfoscillate
hello list, i have created a poll about the tuning controls of the forthcoming a111/2 dynamic vco. the poll will close in two weeks, because we need to find a decision fast, so we can probably see this module released by end of this year. please take a few seconds of your time an
2006-09-13 by Doepfer_a100@yahoogroups.com
Enter your vote today! A new poll has been created for the Doepfer_a100 group: which tuning controls would you prefer for the forthcoming a111/2 dynamic vco? o coarse freq pot with extended range + fine freq pot (like on the preliminary frontpanel) o coarse freq pot with standard
2006-09-13 by selfoscillate
--- In Doepfer_a100@yahoogroups.com, "vliesgaard" wrote: > > At low clock frequency's you start to hear the HSVCO. > > To remove this it is suggested that you filter the output. > > But (I think, not yet received my A-188-1) you can also subtract the > clock from the output with
2006-09-13 by hardware@doepfer.de
This will not work as the clock pulses appear with different levels at the BBD output (= the audio input signal sampled at each clock pulse). But the BBD clock signal has a constant level. Best wishes Dieter Doepfer > -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogro
2006-09-13 by hardware@doepfer.de
The standard wah-wahs I know are not able to send a CV as the potentiometer operated by the foot is part of the filter circuit. You will have to modify the wah-wah, e.g. a three-terminal switch that disconnects the three potentiometer terminals from the filter circuit and uses th
2006-09-13 by William Soraparu
Hi Harry, tell me of the modules you have besides the A-149. I'm sure all of us can assist you!! William Hawaii amnesia wrote: Hi all I just bought my first Doepfers this week....I didn't want to ask for sounding stupid, but with the A149 can someone give me an example of a patch
2006-09-13 by hardware@doepfer.de
Yes. Only 3-4 A-177 modules have been ordered per month. It took about 3 years to sell the last batch ! Best wishes Dieter Doepfer > -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com > [mailto:Doepfer_a100@yahoogroups.com]Im Auftrag von ilanode > Gesendet: Die
2006-09-13 by vliesgaard
At low clock frequency's you start to hear the HSVCO. To remove this it is suggested that you filter the output. But (I think, not yet received my A-188-1) you can also subtract the clock from the output with e.g. an A-138c. Are there any advantages/disadvantages between the 2 me
2006-09-13 by tkrakowiak
hello group, will a regular wah-wah send a cv? best t On 12/09/06, ilanode wrote: > > The A177 is poor selling? Can't believe it since it's one of my favs. > Regards, Ingo > > --- In Doepfer_a100@yahoogroups.com , > wrote: > > > > If anybody is still interested in these modules:
2006-09-12 by ilanode
The A177 is poor selling? Can't believe it since it's one of my favs. Regards, Ingo --- In Doepfer_a100@yahoogroups.com, wrote: > > If anybody is still interested in these modules: > > We have less than ~ 10 A-177 modules left (foot controller). > We have less than ~ 20 A-197 mod
2006-09-12 by Julian
Allan Hall did a lot of this kind of stuff (you still about allan? ; ) But heres a few comments - If youre keeping the layout the same (i assume you have to because of the pcb mounted components) then why not just keep the metalwork also? Youll need to remove the old ink. Some so
2006-09-12 by hardware@doepfer.de
Maybe our Corel Draw files will help you. So far we use Corel Draw for our front panel printing. www.doepfer.com > PRODUCTS > A-100 > Module overview > Corel Draw file A100_System.cdr Best wishes Dieter Doepfer > -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.
2006-09-12 by IZAM
I wonder if anyone can advise me on how i could take a series of modules by doepfer and livewire and plan b and remove the front panels and design new matching panels for them all ? front panel designer people shaeffer (i think thats the company ?) my question is , is it simply a
2006-09-12 by hardware@doepfer.de
If anybody is still interested in these modules: We have less than ~ 10 A-177 modules left (foot controller). We have less than ~ 20 A-197 modules left (analog meter). These modules will no longer be manufactured because of the poor sales. Best wishes Dieter Doepfer
2006-09-12 by David Salter
Ingo, I know that's the only downside to the idea, it requires 4hp just for the switches :( Cheers David David Salter Senior Consultant PSG Reuters Messaging: david.salter.reuters.com@reuters.net (t) +44 (0)20 7542 2402 | (m) 07990562402 | (f) 52699 Get the latest news at Reuters
2006-09-12 by selfoscillate
hello david, i'm afraid that this solution would eat up too much panel space, but anyway i will put it on the list too. best wishes ingo --- In Doepfer_a100@yahoogroups.com, David Salter wrote: > > Hi Ingo, > > I've always like the idea of the Emu VCO with individual octave > swi
2006-09-12 by selfoscillate
i think because of the waveshaping it can sound different, but of course it will have some kind of cem-flavour. maybe the soon coming sound examples will convince you. best wishes ingo --- In Doepfer_a100@yahoogroups.com, "J S" wrote: > > Is that going to make it sound like a CEM
2006-09-12 by Ross Goniakowski
i agree fully.... James Husted wrote: I have had experience with a couple of synths with multi turn VCO tuning. I've had 3 EMS Synthi (2 AKS and a VCS3) and a 2 and 4 voice Oberheim. Both units did not have real mult-turn pots but instead had multi turn knobs that geared down to
2006-09-12 by James Husted
I have had experience with a couple of synths with multi turn VCO tuning. I've had 3 EMS Synthi (2 AKS and a VCS3) and a 2 and 4 voice Oberheim. Both units did not have real mult-turn pots but instead had multi turn knobs that geared down to standard pots (a much cheaper solution
2006-09-11 by erase
Hello list, I have a Doepfer A100P with PSU2 and would like trade it for a dito rack .. (with PSU2 of course.) Located in Sweden Email info@erasemusic.com Thanks *********************************** www.myspace.com/djerase email: info@erasemusic.com msn: erasemusic@msn.com aim: er
2006-09-11 by J S
Is that going to make it sound like a CEM vco? In that case I'm not that excited anymore............I have like 6 cem vco's already... 2006/9/11, hardware@doepfer.de : > > Right. The CEM3394 is used in the A-111-2. > > > Best wishes > Dieter Doepfer > > > -----Ursprüngliche Nachr
2006-09-11 by Bakis Sirros
hello ingo, option 2 is best and the most practical!! but, if the multiturn knob looks realy nice (like on the ems vcs3) i would prefer the multiturn knob... anyway, for me, option 2 or option 3 are better than option 1 for sure! best regards, Bakis. --- selfoscillate wrote: > >
2006-09-11 by levka0
Hi All, First, let me say that I am very very excited with the two modules having the features that are planned. Just one small suggestion for the A-111-2: A single switch that enables selection of either 4 pole (24 db/oct) or 2 pole mode (12 db/oct) for the VCF. (Provided that t
2006-09-11 by David Salter
Hi Ingo, I've always like the idea of the Emu VCO with individual octave switches, thus allowing you to switch from 32' to 4' without going through 16' & 8', great for live work. david David Salter Senior Consultant PSG Reuters Messaging: david.salter.reuters.com@reuters.net (t)
2006-09-11 by ringmod45
Hi Ingo, Here are some extra suggestions. Option 2, should have a switch that switches between octave control plus with regular coarse and fine tune knobs, and no octave control with regular coarse and fine tune knobs. This way you have the option to sweep the oscillator through
2006-09-11 by amnesia
Hi all I just bought my first Doepfers this week....I didn't want to ask for sounding stupid, but with the A149 can someone give me an example of a patch to use for this what is CVDin etc? oh and again adsrs i understand on my Jupiter 8 but can someone give me a patch example ple
2006-09-11 by selfoscillate
hello list, i'd like to start a poll, but want to collect additional ideas first. the preliminary frontpanel design of the a111/2 dynamic vco offers two knobs for tuning: coarse tune and fine tune. lets say, that this is option 1. actually there are two other ideas regarding the
2006-09-11 by Silas Johansen
I have a G3 rack on top of a G6, so three rows of modules that I bought used. The G6 was a BS1 with unaltered layout when I got them about half a year ago, the G3 contained two extra EG's, a fixed filter bank, a CV source, a voltage inverter, a dual VCA and some blanks. Naturally
2006-09-11 by Dubshot
Good morning, Personally I like these values, I'm not into echo's that are timed dead straight. Thanks and greetings Anton > Anton, > > the six taps of the BBD are prescribed by the circuit used (MN3011) and > cannot be changed. It's the only BBD chip with several taps I know. >
2006-09-11 by hardware@doepfer.de
Guido, we have a special information page about vactrols: http://www.doepfer.de/a100_man/Vactrol.htm In general vatrols are very slow (compared to other elements like transistors, transistors or diodes) but there are minor differences due to the basic material used in the photo-s
2006-09-11 by hardware@doepfer.de
Anton, the six taps of the BBD are prescribed by the circuit used (MN3011) and cannot be changed. It's the only BBD chip with several taps I know. Best wishes Dieter Doepfer > -----Ursprüngliche Nachricht----- > Von: Doepfer_a100@yahoogroups.com > [mailto:Doepfer_a100@yahoogroups